Home › MYPV › MYPV AC THOR/AC ELWA 2 with ENIRIS smartgridOne Integration Guide PDF
ℹ️ Document Conversion Notice: This page was converted from the original file for easier reading. Diagrams/images may appear only in the original PDF below.
Document preview
File info: application/pdf · 4 pages · 328.29KB

MYPV AC THOR / AC-THOR 9s / AC ELWA 2 with ENIRIS smartgridOne

1. Initial Settings on the my-PV Device

Before commissioning, please be sure to read the included installation manual and the online operating manual.

You can find the AC•THOR operating manual here.

You can find the AC ELWA 2 operating manual here.

2. Settings on the my-PV Device

On the display or in the web interface, under 'Control', select 'Modbus TCP' as the control type.

UI Example:

09.04.25 07:01:00 Control 8/13 [info] [help]

Modbus TCP

3. Communication with ENIRIS smartgridOne

AC•THOR or AC ELWA 2 are connected to ENIRIS smartgridOne in the network via a router. Within this network, the my-PV device receives the command for how much power it should output.

Notes

  • Up to 8 my-PV devices can be controlled!
  • In operating mode M3: Third-party control types may not be able to provide the full possible power!
  • Do not connect the my-PV device directly to the inverter or battery system!

4. Settings on the ENIRIS smartgridOne

Step 1 & 2: Adding a Device

The ENIRIS smartgridOne interface allows you to add various devices. The first step involves selecting the type of device you wish to add.

Description of ENIRIS smartgridOne UI: "What kind of device do you want to add?" screen. Icons represent: Energy meter, Solar inverter, Heat pump, Charging station, Battery systems, On/off controlled load, Building management system, Water meter.
Below the device types, a row of brand logos is displayed, including HUAWEI, iwell, KSTAR, KEHUA TECH, MYPV, Octave energy, MARSTEK, SunSpec Modbus CERTIFIED, Omni Power, POWER PSSONIC, POWEROAD, refurb.battery.

Step 3: Selecting the Device Model

After selecting the device type, you will be prompted to choose the specific model or device series.

Description of ENIRIS smartgridOne UI: "Which device model are you adding?" screen. Options include: "My model or device series is not listed", "AC Elwa 2", "AC Elwa-E", "Acthor", "Acthor 9s", "Acthor CH", "Acthor I", "SOL THOR".

Step 4: Entering Device Network Parameters

Here, you enter the network parameters of the device or the converter/gateway used to access the device.

Description of ENIRIS smartgridOne UI: "Device network parameters" screen. Options are: "Option 1: Add by MAC address (recommended for networks with DHCP)" and "Option 2: Add by fixed IP address, domain or hostname".

Step 5: Scanning for Devices

The system scans the network for the specified device.

Description of ENIRIS smartgridOne UI: "Finished scanning" screen. Shows "Found devices: 1". Options include "Device not found?", "Click here to check out the troubleshooting page", "End scan and go to results", "Show detailed logs", and "Status messages:".

Step 6: Device/Group Settings

This section allows you to configure specific settings for the added device or group.

SettingHelpCurrent valueNew value
Name[info] MyPV AC Elwa 2 1601502405110004MyPV AC Elwa 2MyPV AC Elwa 2
Nominal power (kW)[info]3.53.5
Priority[info]NormalNormal
Is the device single or three phase?[info]Single phase( ) Single phase
( ) Three phase
Operating voltage[info]Same as the main circuit breakerSame as the main circuit breaker
Nominal voltage type[info]Phase-neutral (line-neutral)( ) Phase-neutral (line-neutral)
( ) Phase-phase (line-line)
Nominal voltage (V)[info]230.0230.0

The save button is located at the bottom of this page.

my-PV GmbH

Betriebsstrasse 12

4523 Neuzeug

www.my-pv.com

Changes reserved.

MYPV - Empowering the Solar Future

Original Document

If the viewer doesn’t load, open the PDF directly.