Unitech TB110 Quick Start Guide

Function Introduction

The device features buttons and ports on its sides and top. On the top edge, there are 'Power volume' buttons and a 'Micro SD' card slot. The left side has a 'Kensington Lock' slot and a 'Hang rope hole'. The right side includes a '3.5mm Headset' jack, a 'USB 3.0' port, a 'USB 2.0' port, a 'DC Jack' for power, and a 'Mic' (microphone).

The front of the device has a 'Front Camera' with a 'Camera LED', a 'Power LED', a 'Charging LED', and a 'Light Sensor'.

The bottom edge features 'Docking Contact Pins'.

Rear View

The rear of the device shows a 'Rear camera'. On the bottom edge, there is an 'Air vent' and a 'Speaker'.

Inserting/Removing SD Card

To install or remove the SD card, follow the indicated method for the 'Micro SD' slot.

A close-up view shows the 'Micro SD' card slot on the device, with an arrow indicating the insertion or removal process.

Notices and Safety Information

General Usage Restrictions

• Do not use electronic equipment in restricted areas like airports, hospitals, or gas stations.
• Do not use the product while driving a vehicle for safety.
• Keep the product away from vehicle airbags to prevent potential safety issues.
• Avoid using the product during thunderstorms.
• While waterproof, do not expose the product to water or moisture for extended periods.
• Operating temperature range: -20°C to +45°C. Storage temperature range: -40°C to +70°C. Extreme temperatures can affect performance and service life.
• Use only original rechargeable lithium batteries. Low-quality batteries can affect performance, service life, and pose an explosion risk.
• Although tested for harsh environments, avoid improper use.
• Do not disassemble the product. Contact authorized service centers for repairs.
• Dispose of the device properly at the end of its service life to prevent environmental pollution.
• When replacing the battery or using an external power supply, shut down the device completely first to prevent damage.
• This is a Class B product that may cause radio interference; preventive measures may be required.
• For Singapore, use AC adaptors with 3-pin and 2-pin detachable pins.

Battery Instructions

• The product uses a rechargeable lithium battery. Charge when power is low. To maintain battery life, it is recommended to deplete the battery's power before charging.
• Remove the battery charger from the power supply when not in use. Do not connect the charger for more than one week to avoid shortening battery life.
• Battery charging limits are affected by temperature; the battery may need cooling or warming before charging.
• Use the battery only for its intended purpose to prevent short-circuiting. A short circuit occurs when conductive material connects positive and negative terminals.
• Do not use a damaged battery.
• Extremely cold or hot environments shorten battery life and may cause malfunction, even if fully charged.
• Do not put the battery in fire. Dispose of batteries properly at a recycling station according to local laws and regulations.

SAR and RF Exposure Information

European SAR Limit

The SAR limit for Europe is 2.0 W/kg. Device type BT110 has been tested against this limit. The highest reported SAR value during certification for body-worn operations (0 cm separation) is 0.075W/kg. To maintain compliance, use accessories that maintain 0 cm separation and do not contain metallic components. Accessories not meeting these requirements should be avoided.

FCC and ISED SAR Limit

The SAR limit for FCC and ISED is 1.6 W/kg averaged over one gram of tissue. Device type BT110 has been tested against this limit. The highest SAR value reported under this standard during certification for use on the body is 0.353 W/kg. This device was tested for typical body-worn operations with the back of the handset kept 0 cm from the body. To maintain compliance with FCC and ISED RF exposure requirements, use accessories that maintain a 0 cm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC and ISED RF exposure requirements, and should be avoided.

Note: High sound pressure is associated with a risk of hearing damage

FCC and Industry Canada Compliance

This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to two conditions: (1) the device may not cause harmful interference, and (2) it must accept any received interference, including interference that may cause undesired operation.

French Translation: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

NOTICE: Changes or modifications not expressly approved by Unitech Electronics Co., LTD. may void FCC authorization.

NOTE: This equipment has been tested and found to comply with Class B digital device limits per FCC Part 15. These limits provide reasonable protection against harmful interference in residential installations. The equipment generates, uses, and radiates RF energy. If not installed and used per instructions, it may cause harmful interference to radio communications. No guarantee of no interference in a particular installation. If interference occurs (determined by turning the device off/on), try these measures: Reorient or relocate the receiving antenna; increase separation between equipment and receiver; connect to a different circuit than the receiver. Consult dealer or technician for help.

NOTICE: This Class [B] digital apparatus complies with Canadian ICES -003. Cet appareil numérique de la classe [B] est conforme à la norme NMB - 003 du Canada.

RF mode and power tune-up refer to appendix A.

European Union Frequency Restrictions

This device is restricted to indoor use in the European Community when operated in the 5150MHz ~ 5250MHz frequency range to reduce interference potential. Restriction applies in: BE, BG, CZ, DK, DE, EE, IE, EL, ES, FR, HR, IT, CY, LV, LT, LU, HU, MT, NL, AT, PL, PT, RO, SI, SK, FI, SE, UK.

Declaration of Conformity: Hereby, Unitech Electronics Co., LTD. declares that the radio equipment type [BT110] is in compliance with Directive 2014 / 53 /EU.

Normal Mode RF Power Range (WLAN, Bluetooth)