2GIG-DW100-345 Wireless Door/Window Contact

Brand: 2GIG (a Nice brand)

Operating Instructions

The indoor Door/Window Contact (2GIG-DW100-345) is designed for use on doors, windows, and other objects that open and close. The sensor transmits signals to the control panel when a magnet mounted near the sensor is moved away from or closer to the sensor. The sensor has an external input that accepts N/C or N/O dry contact devices. The sensor is also equipped with a cover tamper for additional security.

Battery Installation & Replacement

If a sensor battery is low, a low battery notification will be indicated on the 2GIG Alarm Control Panel's screen. When the 2GIG alarm system indicates that there is a sensor with a low battery, replace the battery immediately. Use only the recommended replacement batteries (see Specifications). To install or replace the battery:

To remove the sensor cover, use your finger to press the tab on the end of the case. This will disengage the clip holding the cover to the base.
The battery will only slide out in one direction. One side of the battery clip has a stopping edge. Using your thumb, gently apply pressure in the direction away from the battery clip edge that offers resistance.
Insert the replacement battery with the + sign facing out.

WARNING! The polarity of the battery must be observed. Improper handling of lithium batteries may result in heat generation, explosion or fire, which may lead to personal injuries. Replace only with the same or equivalent type of battery as recommended by the manufacturer (see Specifications). Batteries must not be recharged, disassembled or disposed of in fire. Disposal of used batteries must be made in accordance with the waste recovery and recycling regulations in your area. Keep away from small children. If batteries are swallowed, promptly see a doctor.

Encrypted/Unencrypted Mode Switch

The sensor is capable of transmitting signals in encrypted mode or unencrypted mode. The mode is set through a switch inside the sensor (see Figure 2). The sensor comes with default set to encrypted enabled. To change to unencrypted mode:

Open the sensor housing and remove the battery from the slot.
Locate the dip switch and note the switch setting: X indicating encrypted and Y for unencrypted mode. Move the switch position to Y.
Insert the battery back and close the housing.
If the sensor was learned into a panel in a different mode previously, please remove and re-learn the sensor under the new mode.

Programming

The following steps describe general guidelines for programming (learning) the sensor into the alarm control panel memory. For more details, refer to the 2GIG Panel Installation & Programming Instructions.

Put the panel in sensor Learn mode.
Pull battery tab to start auto-learn with a panel.
Re-attach the sensor back cover.

Mounting Guidelines

Use the following guidelines for internal switch usage:

Mount the sensor on the door frame and the magnet on the door. If the sensor is used on double doors, mount the sensor on the least-used door and the magnet on the most-used door.
Make sure the alignment arrow on the magnet points to the alignment mark on the sensor (see Figure 1).
Place sensors at least 4.7 in. (12 cm) above the floor to avoid damaging them.
Avoid mounting sensors in areas where they will be exposed to moisture or where the sensor operating temperature range of 32 to 120°F (0 to 49°C) will be exceeded.
Use spacers (included) to align the magnet with the sensor.
Avoid mounting sensors in areas with a large quantity of metal or electrical wiring, such as a furnace or utility room.

To mount the sensor:

Place the base of the sensor in the desired location and secure with included screws or adhesive.
When mounting the magnet, line up the arrow on the magnet with the middle line on one side of the sensor (see Figure 3). Mount the magnet no more than 0.4 in. (1 cm) away from the sensor. Secure the magnet with included screws or adhesive.

To use the external input:

Repeat above instructions for mounting.
Route the wire through access hole.
Wire external contact wires into sensor terminal block.
Configure contact device as NO or NC at the panel.

Specifications

Code Outputs	Transmitter Frequency	Supervisory Interval	External Input	Reed Sensitivity	Magnet Type	Magnet Dimensions (L x W x H)	Sensor Dimensions (L x W x H)	Weight (including battery & magnet)	Housing Material	Color	Operating Temperature	Relative Humidity	Battery (included)	Regulatory Listing(s)	Panel Programming Sensor Loop	Warranty*	Included Accessories
Alarm; Alarm Restore; External Alarm; External Restore; Tamper; Tamper Restore; Supervisory; Low Battery	345MHz	70 minutes	Accepts N/C or N/O dry contact devices	0.94 in. (2.39 cm) maximum gap	Rare earth	2.42" x 0.58" x 2.42"	2.42" x 1.07" x 0.58"	1.1 oz. (31.2 g)	ABS plastic	White	32° to 120°F (0° to 49°C)	5-95% Non-Condensing	CR2450	ETL, FCC Part 15, Industry Canada	Loop 1: external contact Loop 2: magnet/reed switch	Two (2) years	Two (2) Phillip's flat-head screws, one (1) two-pin connector with a 12" flying 2-wire lead, adhesive strip

FCC & IC Notice

This device complies with Part 15 of the FCC Rules and Industry Canada license exempt standard(s). Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician to help.

FCC: Federal Communication Commission (FCC) Radiation Exposure Statement: When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements.

IC: Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

WARNING: Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.

Important Safety Information

WARNING INGESTION HAZARD: This product contains a button cell or coin battery. DEATH or serious injury can occur if ingested. A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours. KEEP new and used batteries OUT OF REACH of CHILDREN. Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.

Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate. Even used batteries may cause severe injury or death. Call a local poison control center for treatment information.

Only use this product with CR2450 type batteries. The nominal battery voltage is 3Vdc. This product uses non-rechargeable batteries and are not to be recharged. Do not force discharge, recharge, disassemble, incinerate or heat above specified operational temperature. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.

Ensure the batteries are installed correctly according to polarity (+ and -). Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries. Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

Limited Warranty

This Nice North America LLC product is warranted against defects in material and workmanship for two (2) years. This warranty extends only to wholesale customers who buy direct from Nice North America LLC or through Nice North America LLC's normal distribution channels. Nice North America LLC does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer's warranty, if any.

There are no obligations or liabilities on the part of Nice North America LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages, with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties for functionality, are valid only until the warranty expires. This Nice North America LLC Warranty is in lieu of all other warranties expressed or implied.

Regulatory Information

We, Nice North America, LLC of 5919 Sea Otter Place STE 100, Carlsbad, CA 92010, declare under our sole responsibility that the device, 2GIG-DW100-345 complies with Part 15 of the FCC rules.

Customer Service

Nice North America LLC
5919 Sea Otter Place, Suite 100
Carlsbad, CA 92010
Phone: 760-438-7000
Hours: Monday - Friday, 5:00 a.m. - 4:00 p.m. PST

Niceforyou.com