Alphamarts PV-410 Use and Care Guide
PREMIUM HOME SOLUTION
Safety Information
- Do not completely tighten screws until all screws are started. Tighten each bolt firmly and properly.
- Some parts may contain sharp edges. Wear protective gloves as necessary.
- Children under the age of 16 should not be engaged in the assembly, removal or disassembly of the product.
- Children under the age of 10 should be supervised by a competent adult while using this furniture.
- Please keep children out of the assembly area during assembly.
- This set is heavy, and may require two adults for safe assembly.
- Never use this product as a support. Do not shake, lean, or climb on the product at any time.
[warning] DANGER: Do not allow children to play with plastic wraps or small parts to prevent potential choking hazard.
[warning] CAUTION: Read all the instructions before assembly. Failure to do so may result in faulty assembly and potential injury!
Warranty
LIMITED WARRANTY
This warranty is a limited warranty, and applies to the original purchase. This is a residential warranty and does not apply to commercial use. This collection carries a (1) year limited warranty and is valid from original date of purchase to the original owner (proof of purchase required).
WHAT IS COVERED
We warrant the frame to be free of Manufacturing defects to the original purchaser for one year.
WHAT IS NOT COVERED
This warranty does not cover commercial use, hardware, acts of nature, fire, freezing and abusive. In addition, purchased parts are not covered under this warranty.
We reserve the right to make substitutions with similar merchandise, if the model in question is no longer in production.
For a copy of our full limited warranty, please contact our customer service team.
Pre-assembly
Assemble the item on a soft, non-abrasive surface, such as carpet or cardboard to avoid damaging the item. Seek assistance to assemble bulky or heavy items.
[note] Identify all parts packed in the carton against the parts list. Remove all the protective material carefully and DO NOT use a knife to prevent scratching the furniture.
[note] Hardware not shown to actual size.
Package Contents
Parts List
| Part ID | Description | Quantity |
|---|---|---|
| A | Frame Component | 2PC |
| B | Frame Component | 2PC |
| C | Leg Component | 4PC |
| D | Support Bar | 2PC |
| E | Connector Piece | 1PC |
| F | Cap/Cover | 1PC |
Hardware List
| Hardware ID | Description | Quantity |
|---|---|---|
| AA | M6*50mm bolt | 4PC |
| BB | M6*45mm bolt | 4PC |
| CC | M6*30mm bolt | 2PC |
| DD | M6*15mm bolt | 16PC |
| EE | M6 washer | 32PC |
| FF | M6 nut | 6PC |
| XX | Socket wrench | 1PC |
| YY | Wrench | 1PC |
Assembly
Step 1
Attach two main frame pieces (A) together using four M6*50mm bolts (AA), eight M6 washers (EE), and four M6 nuts (FF). Do not fully tighten screws until Step 2 is completed.
[diagram_description] Shows two 'A' parts being joined, with close-up showing AA bolt, EE washer, FF nut.
Step 2
Attach two additional main frame pieces (A) to the structure assembled in Step 1 using four M6*45mm bolts (BB) and eight M6 washers (EE). Do not fully tighten screws until Step 2 is completed.
[diagram_description] Shows two more 'A' parts being attached to the existing structure, with close-up showing BB bolt and EE washer.
Step 3
Attach four leg components (C) to the main frame (A) using eight M6*30mm bolts (CC) and sixteen M6 washers (EE). Do not fully tighten screws until Step 5 is completed.
[diagram_description] Shows four legs (C) being attached to the main frame (A), with close-up showing CC bolt and EE washer.
Step 4
Attach two support bars (D) to the frame (A) using four M6*15mm bolts (DD) and eight M6 washers (EE). Attach one connector piece (E) between the support bars (D) using two M6*15mm bolts (DD) and four M6 washers (EE). Do not fully tighten screws until Step 5 is completed.
[diagram_description] Shows support bars (D) being attached to the frame (A), and a connector piece (E) between them. Close-up shows DD bolt, EE washer, CC bolt, FF nut.
Step 5
Attach the remaining two support bars (D) to the frame component (B) using four M6*15mm bolts (DD) and eight M6 washers (EE). Tighten all screws completely.
[diagram_description] Shows the final support bars (D) being attached to frame component (B). Close-up highlights the use of EE washer and DD bolt.
Step 6
Place the main tabletop component (A) onto the assembled base. Ensure the covers or caps (F) are correctly seated in the designated holes.
[diagram_description] Shows the tabletop (A) being placed on the assembled legs and frame. Close-up shows part F fitting into a hole.
Cleaning and Maintenance
- Clean the furniture with a damp cloth, rinse thoroughly. Dry frame parts completely. Do not use bleach, acid or other solvents on the textile or metal parts.
- We recommend the use of furniture covers to protect the product when not in use.
- Inspect and tighten all screws on a regular basis to ensure proper performance and safety.
- In order to prolong the life and beauty of your product, we recommend storing it in a dry and protected area during off season periods.
Contact Information
Questions, problems, missing parts? Before returning to the store please contact our Customer Service:
Email: service@alphamarts.com
Phone: 1-877-606-2818
