Instruction Manual for Fujian models including: FCS950U, 2AM6U-FCS950U, 2AM6UFCS950U, FCS950U WiFi and Bluetooth Module, FCS950U, WiFi and Bluetooth Module, Bluetooth Module, Module
Fujian Newland Payment Technology Co.,Ltd. FCS950U 2AM6U-FCS950U 2AM6UFCS950U fcs950u
Fujian Newland Payment Technology Co.,Ltd. FCS950U WiFi & Bluetooth Module 2AM6U-FCS950U 2AM6UFCS950U fcs950u
Wi-Fi 5 & Bluetooth 5.0 Module Ultra-compact LCC Package FCS950U is a high-performance 2.4 GHz and 5 GHz Wi-Fi 5 and Bluetooth Low Energy (BLE) module featuring 1T1R in LCC package. It can be used to establish WLAN and Bluetooth connections. Designed with a reliable SDIO 3.0 interface to provide WLAN capability, it also provides an integrated PA with advanced architecture enhancement to achieve satisfying receiver sensitivity in noisy home scenarios. With an ultra-compact size of 12.0 mm × 12.0 mm × 2.15 mm, FCS950U optimizes the size and cost for end-products. FCS950U supports WEP, WPA, WPA2, WPA3-Personal and WPA3-Enhanced Open, and both single and multiple channel concurrency. Compliant with Bluetooth 5.0, FCS950U provides the concurrent operation of Classic Bluetooth and BLE, supporting LE 2 Mbps, LE Advertise Extension, Long Range, AoD Rx Direction Finding, BLE Mesh, multiple piconets and up to 8 concurrent BLE links. Surface-mount Technology (SMT) makes FCS950U an ideal solution for durable and rugged designs. The low profile and small size of LCC package ensure that it can be easily embedded into size-constrained applications and provide reliable connectivity with these applications. The advanced package and the laser-engraved label with better heat dissipation and indelible markings allow for large-scale automated manufacturing which has strict requirements on cost and efficiency. FCS950U can meet Wi-Fi & Bluetooth application design requirements in fields including industry, POS and printing. Key Features Dual-band 2.4 GHz and 5 GHz Wi-Fi and BLE SDIO 3.0 interface that features higher data transmission rate and lower power consumption Faster time-to-market: simple design minimizes design-in time and development efforts Wide operating temperature range: -40 °C to +85 °C Ultra-compact Size LCC Package IEEE 802.11 a/b/g/n/ac SDIO Interface Operating Temperature Range: -40 °C to +85 °C BLE (Bluetooth 5.0) Version: 1.0.0 Status: Preliminary Wi-Fi & Bluetooth Module WLAN Protocol Wi-Fi Frequency Band Wi-Fi Antenna Wi-Fi Modulation Mode 2.4 GHz Channel Bandwidth 5 GHz Channel Bandwidth Encryption Mode Wi-Fi Operating Mode Bluetooth Protocol Dimensions Weight Temperature Range Operating Temperature Range Data Rate (Max.) 802.11a 802.11b 802.11g 802.11n 802.11ac Interfaces SDIO 3.0 PCM UART Wi-Fi/Bluetooth Antenna Interface Electrical Features Power Supply Voltage Power Consumption Certification Regulatory Wi-Fi Performance FCS950U IEEE 802.11a/b/g/n/ac 2.4 GHz/ 5 GHz 1×1 DSSS, DBPSK, DQPSK, CCK, BPSK, QPSK, 16QAM, 64QAM, 256QAM 20/ 40 MHz 20/ 40/ 80 MHz WPA3 AP/STA Bluetooth 5.0 12.0 mm × 12.0 mm × 2.15 mm 0.55 g -40 °C to +85 °C 54 Mbps 11 Mbps 54 Mbps 150 Mbps 433 Mbps × 1 (for Wi-Fi) × 1 (for Bluetooth) × 1 (for Bluetooth) ×1 VBAT: 3.23.4 V, Typ. 3.3V Max. current at Tx mode: 210 mA @ VBAT Europe: CE America: FCC Canada: IC Brazil: Anatel China: SRRC Australia/New Zealand: RCM Maximun Peak Output Power(Conducted) 2.4 GHz 2414-2462 MHz(802.11b/g/n ht20) 2422-24522 MHz(802.11n ht40) 23.54 dBm Wi-Fi & Bluetooth Module Wi-Fi Performance Band1: 5180-5240 MHz(802.11a/n ht20/ac vht20) 5190-5230 MHz(802.11n ht40/ac vht40) 5210 MHz(802.11ac vht80) Band2: 5260-5320 MHz (802.11a/n ht20/ac vht20) 5270-5310 MHz(802.11n ht40/ac vht40) 5290 MHz(802.11ac vht80) 5 GHz Band3: 5500-5720 MHz (802.11a/n ht20/ac vht20) 5510-5710 MHz(802.11n ht40/ac vht40) 5530-5690MHz(802.11ac vht80) Band4: 5745-5825 MHz (802.11a/n ht20/ac vht20) 5755-5795 MHz(802.11n ht40/ac vht40) 5775 MHz(802.11ac vht80) Bluetooth Performance BR EDR (/4-DQPSK) EDR (8-DPSK) BLE Ordering Code FCS950UABMD Antenna DBS One Wi-Fi/Bluetooth Antenna - Maximun Average Output Power(Conducted) 16.57 dBm in 5150-5250 MHz Band 16.86 dBm in 5250-5350 MHz Band 17.15 dBm in 5470-5725 MHz Band 17.18 dBm in 57250-5850 MHz Band Maximun Peak Output Power(Conducted) 9.15 dBm 10.79 dBm 11.08 dBm 6.58 dBm Coexistence with Cellular Module - Development Board (Only for Debugging) FCS950UABM2 Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01r01 2.2 List of applicable FCC rules CFR 47 FCC PART 15 SUBPART C&E has been investigated. It is applicable to the modular. 2.3 Specific operational use conditions This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. 2.4 Limited module procedures Not applicable 2.5 Trace antenna designs Not applicable 2.6 RF exposure considerations To maintain compliance with FCC's RF Exposure guidelines, This equipment should be installed and operated with minimum distance of 20cm from your body. 2.7 Antennas This radio transmitter FCC ID: 2AM6U-FCS950U has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Antenna Antenna Antenna Manufacturer Chain type Input impedance (Ohm) Maximum antenna gain ZHONGTIAN 1 XUN FPC 50 2.39 dBi/2.4-2.5GHz (WIFI/BT Ant) 2.8 Label and compliance information The final end product must be labeled in a visible area with the following" Contains FCC ID: 2AM6U-FCS950U " 2.9 Information on test modes and additional testing requirements Host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when the module is installed in the host. 2.10 Additional testing, Part 15 Subpart B disclaimer Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B FCC Warning: Any Changes expressly or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator &you body.