SEIKAKU
User Manual for AUDIO MATRIX models including: RPM200 Factor Digital Multi Zone Paging Microphone, RPM200, Factor Digital Multi Zone Paging Microphone, Digital Multi Zone Paging Microphone, Multi Zone Paging Microphone, Paging Microphone, Microphone
SEIKAKU TECHNICAL GROUP LIMITED
Thanks to purchase the product of our company, please read this manual carefully before any operation. Note: This guide contains all the information needed for the product. There might be some differences between the item and its description; please refer to the real product for the
File Info : application/pdf, 10 Pages, 6.39MB
DocumentDocumentUSER'S MANUAL AUDIO MATRIX RPM200 Paging Station AUDIO MATRIX AUDIO MATRIX AUDIO MATRIX INDEX 01 SAFETY RELATED SYMBOLS 02 WARNING 03 IMPORTANT SAFETY INSTRUCTIONS 04 FOREWORD 05 AUDIO MATRIX 06 SYSTEM PREVIEW 07 BASIC OPERATION 08 PHYSICAL INSTALLATION 09 OPERATION 10 SOFTWARE CONTROL 11 FIRMWARE UPDATE 12 FAQ 13 SPECIFICATIONS AUDIO MATRIX 1 1 2 3 3 4 7 8 8 9 13 13 14 AUDIO MATRIX 1 AUDIO MATRIX FAQ c. Devices can not be found 1). Please make sure devices are linked well. 2). Please make sure all devices were assigned their unique ID with MatrixSystemEditor at the initial configuration. 3). If this system using several sever hosts for extend linkage, please make sure the system were set rightly by DANTE Controller. Please refer to "Configuration for multiple sever host linked" part for details. 4). Please try to restart all the devices. 5). If all steps above checked, defects still exited, please insult the professional for help. d. Software can not start 1). Please make sure the operating system version is later than Windows 7. 2). Please make sure NetFreameWork4.5.* suit is installed. 3). Please make sure no firewall or antivirus software affects their running. 4). Please make sure system acquired valid IP and shown no error. 5). If all steps above checked, defects still exited, please insult the professional for help. SPECIFICATIONS MIC Input · Active balanced · Connector: 3-pin female XLR, ,(1 Gnd,2 Signal, 3 LED Power) · Phantom Power: +12VDC @ 6mA Indicators and switch · LCD Display: Zone activation · LEDs: Signal Status · Switch: Push to Talk Ports · RD net to Matrix: RJ45, 100 m CAT 5e cable · USB: For Chimes Sound file (4 seconds) Dimensions · L x H x D: 166 x 53 x 162 mm 14 AUDIO MATRIX FIRMWARE UPDATE For more information about firmware, please visit WWW.SEIKAKU.COM. Please check the hardware version twice to identify the compatibility of firmware tended to upgrade. FAQ a. There is no sound for the system 1). Please check if the device powered on, its screen lit or not. 2). Please make sure "Talk" button was pressed before voicing. 3). Please recheck the setting of MIC volume, make sure it was in a proper position. 4). Please check the channels assignment, make sure the one you output in hooked up with the input at present. 5). Please the amplifier or active speaker on the circuit, make sure they are charged and set appropriately. 6). Please make sure the entire system configuration is set rightly. 7). Please try to restart all the devices. 8). Please make sure all the physical connections are stable and right. 9). If all steps above checked, defects still exited, please insult the professional for help. b. Sound seems to be abnormal 1). Please check the sound sources, low quality input always cause distortion and resonance. 2). Please check the volume setting, consumption overloaded would cause distortion and resonance either. 3). Please try to restart all the devices. 4). Please make sure all the digital linkages are adopted high quality shield cat5e network cable or above, and professional cables for analog too. 5). If there some intermittent clipping sound, please check all the joint point are fixed well. 6). Please make sure devices and cables are not under high magnetic or high radical environment. 7). Please make sure the furthest length form the sever host is no more than 100m. (150m for the grounded linkage) 8). Please make sure the analog transmission also within the fidelity limitation. 9). If all steps above checked, defects still exited, please insult the professional for help. 13 AUDIO MATRIX 2 AUDIO MATRIX FOREWORD Thanks to purchase the product of our company, please read this manual carefully before any operation. Note: This guide contains all the information needed for the product. There might be some differences between the item and its description; please refer to the real product for the features. AUDIO MATRIX Audio Matrix is a system which contains multiple signal inputs and outputs; each input can be assigned to any output like matrix in mathematics. Parameters controls are available for all the inputs and outputs, and are easily changeable; all the configurations can be backed up and restored, easy to copy and to extend. Audio Matrix gives the ability to build complex audio setup in one device providing an instinctive operating interface for both professional and beginner. AUDIO MATRIX SOFTWARE CONTROL Attached Configuration for multiple sever host linked : Dante Control software is required for this action, please visit WWW.SEIKAKU.HK to download. After all the physical linkage confirmed, start the software and set tiks like below in the indicated area. That is to assign the all Broadcast outputs of the pervious device to the all Broadcast inputs of the next one, and so foth except the last ; for the last, we should connect its Broadcast outputs back to the Broadcast inputs of the first one. Here is the example for three host. Step3: MATRIX A8 C routing to MATRIX A8 A Step1: MATRIX A8 A routing to MATRIX A8 B Step2: MATRIX A8 B routing to MATRIX A8 C 3 12 AUDIO MATRIX SOFTWARE CONTROL Master Volume Same as the Mic Volume, 0-32 stage can be adjusted. Priority To define the priority of the device presented, 1-8 accepted, bigger for higher priority, click "Save" button to take effect. Chime Time To define the time of Chime Sound, click upward and downward icon to adjust, 0.5 for variation, 0.5-12S accepted, click "Save" button to take effect. If the chime sound not uploaded, there would be no chime to be played. Zone List To define the quantity of zones, click upward and downward icon to adjust, 12 for variation, 12-192 accepted, click "Save" button to take effect. AUDIO MATRIX SYSTEM PREVIEW Audio Matrix is a system which combines the hardware with software. The core device is Matrix A8 or Matrix D8. The major features are listed below: 1.12 INPUTS and 12 OUTPUTS 2. In case of extension links, the maximum goes up to 192 inputs and outputs. 3.Broadcast different zones simply by paging unit control. 4.A remote control unit can assign the volume in different zones separately. 5.Control signals are transferred individually with dedicated wires separated from the audio stream, avoiding conflicts and improving the flexibility and the reliability. 6. The transmission for audio stream is based on AES/EBU protocol, while the control signal used a RS-485 format. There are six members in the MATRIX SYSTEM family: MATRIX A8 --- Server host; MATRIX D8 --- Server host (Compared to A8, 8 analog I/O for the A8, 8 digital I/O for D8); RVC1000 --- Remote volume control with a link port; RVA200 --- Remote volume control with additional outputs; RIO200 --- Remote analog inputs and outputs; RPM200 --- Remote paging station. By using a combination of the above six devices, most of the broadcasting or routing requirements can be fulfilled. This system fits perfectly for schools, middle and small companies, supermarkets, bars and restaurants, health clubs, small libraries ... The friendly and quick implementation of primary and advance parameters makes easy the design of professional as well as simple applications. Here are some common examples: 11 4 AUDIO MATRIX SYSTEM PREVIEW RPM200 MP3/CD Player Video Plaver MATRIX A8 RETAIL STORE RVA200 Music Server 70/100V Sales Floor Active Speaker Fitting Room Stock Room Office 70/100V Speaker RPM200 MP3/CD Player HEALTH CLUB MATRIX A8 MATRIX A8 MP3/CD Player 70/100V AUDIO MATRIX SOFTWARE CONTROL ID modification Right click on the "DeviceID" position, the function menu popped up as shown; click "Change DeviceID", then enter the number(4 bit) you wanted in the text box, finally click OK to save and to take effect. Note: The first time to use the whole system, initial work to assign ID for each device is necessary for its functioning. Rename device Double click on the device block to enter the page, "APP ID", "Device ID", "Firmware Version" would show automatically according to the information of the device linked. Enter a name into the "Device name" textbox and click "Save" button to take effect. Please make sure the name can only consist of alphabets, numbers and common symbols. RIO200 Active Speakers RVC1000 Aerobics RVA200 Active Speakers Treadmill 5 Locker Rooms Locker Rooms Mic Volume Click the upward icon next to the text box for turning up the volume, and the downward icon for decreasing, 0-32 stage can be adjusted. Click "Save" button to take effect. 10 AUDIO MATRIX OPERATION Broadcast Turn "Scroll" encoder to choose the zones intended to be paged, choose the ones by pushing "Scroll" encoder shortly and repeat until all the zones needed hooked. If all zones needed, just push "Volume" encoder once to select all. After paging zones selected, click the "Talk" button to speak, click again to stop. Normally, there is a chime sound before your speech, you can change or cancel it by replacing or removing the inner sound file. (You should connect the USB port to your computer to accomplish this work.) Please make certain all the zone to be used are selected before speaking, if not, the system would remind you "Select Zones First !" . Rename zones Holding the "volume" to enter the modifying interface, please note only alphabet, number, common used symbol supposed. Reset device Holding "Volume" and "Scroll" encoder together more than 3 seconds to enter factory resetting, "Load default setting ..." would be showed on screen at the same time. The device would restart automatically after process finished. SOFTWARE CONTROL Please use high rated network cable to connect the Ethernet port of PC and the LAN port of serve host device. Then run MatrixSystemEditor, make sure the IP is linked rightly by the remarks given by dialogs. At the main interface, you can drag the device in the left column to the right area, that is the operation to add a device. Please make sure the device you added is physically linked, or there would be no effects even if all settings are saved. Double click for specific operation, here we add a RPM200. If the device is connected properly, the gray rectangle in the left middle would turn to green. 9 SYSTEM PREVIEW RESTAURANT RPM200 MP3/CD Player Video Plaver MATRIX A8 RVA200 AUDIO MATRIX Restaurant Bar Active Satellite Active Sub Terrace TV 4CH 70/100V Cloak Room Toilet MATRIX A8 SCHOOL Video Projector RIO200 Active Speakers RIO200 Active Speakers Classroom 6 Classroom AUDIO MATRIX BASIC OPERATION RPM200--Paging Station RPM200 can manage the zones you want to be broadcasted, the upper quantity is determinated by the amount of the linked server host. And you can choose the prelude as you wished (MP3 and wav are supported, less than 12M.) Zones can be selected for the ones needed or for all, it ensures the information coverage and delivering selectivity at the same time. a. LCD screen It displays the selected zones, the volume and ID number. b. Signal status indicators The green LED indicates the presence of signal when the microphone is ON. The red LED indicates the limit of clipping. c. Communication status indicators When the communication with the MATRIX-A8 is correct, the green LED blinks. In case of problem, the BUSY red LED lights up. d. Volume control and all zone selector It controls the volume of the microphone for each selected zones. By pushing on the button, it selects all zones. e. Zone selector It selects one or several zones by turning the button left or right and pushing on it to validate. f. Push-to-talk switch When the button is pushed, the chimes sounds and the red ring on the microphone lights up indicating that one can talk. 7 AUDIO MATRIX BASIC OPERATION g. XLR connector Female 3 pin XLR connector for the gooseneck electret microphone. It uses a phantom power controlled by software. h. USB port This port is used to load MP3 files for chimes sound. The maximum time for the chimes is 4 seconds. i. RD port Connection to the MATRIX-A8. The maximum CAT 5e cable length is 100 meters. PHYSICAL INSTALLATION Insert the extended reticle terminal to RD port of remote device and the other end to the serve host. Please note link with shield cat5e or better cable, the total length end to end should be no more than 100m. OPERATION Volume adjustment Turn "scroll" encoder to choose the zones intended to be tuned, short pushing to confirm, rotating "Volume" encoder to change volume value of selected ones.(shows on the upper right corner 0-32 can be adjusted) If all zones needed, just push "Volume" encoder once to select all and turn the "Volume" encoder. 8