Diagrams
Diagram 1: A U-shaped connector.
Diagram 2: A small black device with an antenna and a cable.
Diagram 3: A mounting bracket or accessory.
Safety Notices
- Read, follow, and keep these instructions.
- Heed all warnings.
- Only use attachments/accessories specified by the manufacturer.
WARNING: Failure to provide proper ventilation may cause fire hazard. Keep at least 20 mm of clearance next to the ventilation holes for adequate airflow.
WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
WARNING: Do not use this product in location that can be submerged by water.
WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
WARNING: CLASS 1 LASER PRODUCT, IEC/EN 60825-1:2014 - Do not look into the ends of the fiber optic cable or laser source while converters are powered.
Electrical Safety Information
- Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer's label. Connection to a different power source than those specified may result in improper operation, damage to the equipment, or pose a fire hazard if the limitations are not followed.
- There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician.
- This equipment is provided with a detachable power cord which has an integral safety ground wire intended for connection to a grounded safety outlet.
- a. Do not substitute the power cord with one that is not the provided approved type. Never use an adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding wire.
- b. The equipment requires the use of the ground wire as a part of the safety certification, modification or misuse can provide a shock hazard that can result in serious injury or death.
- c. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment.
- d. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short-circuit backup protection.
- e. Protective bonding must be installed in accordance with local national wiring rules and regulations.
Declaration of Conformity (EU)
Hereby, UBIQUITI, declares that this device, Wave-Fiber-ONU, is in compliance with the essential requirements and other relevant provisions of Directives 2014/30/EU, 2014/35/EU. The full text of the EU declaration of conformity and detailed compliance information is available at the following internet address: ui.com/compliance
Ubiquiti International Holding B.V.
Ekkersrijt 3102, Son, Netherlands
Declaration of Conformity (UK)
Hereby, UBIQUITI, declares that this device, Wave-Fiber-ONU, is in compliance with the essential requirements and other relevant provisions of UK Regulations, Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016. The full text of the UK declaration of conformity and detailed compliance information is available at the following internet address: ui.com/compliance
Ubiquiti Distribution UK Limited
2 New Street Square, London, United Kingdom
E-Label Instruction
Product: Ubiquiti® Wave-Fiber-ONU
- Read, follow, and keep these instructions.
- Heed all warnings.
- Only use attachments/accessories specified by the manufacturer.
WARNING: Failure to provide proper ventilation may cause fire hazard.
WARNING: Do not expose this product to rain or moisture.
WARNING: Do not use this product in location that can be submerged by water.
WARNING: CLASS 1 LASER PRODUCT, IEC/EN 60825-1:2014 - Do not look into the ends of the fiber optic cable or laser source while converters are powered.
Power: Power over Ethernet (PoE) 20 - 28 V (DC)
Operating Temperature: -10 to 45 °C
Operating Humidity: 10 to 90% non-condensing
Warranty Information: ui.com/warranty
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Manufacturer: Ubiquiti Inc.
685 Third Avenue, New York, NY 10017, USA
Ubiquiti - Compliance