User Manual for Coretronic Robotics models including: FLIR, P301-D, Wireless Image Transmission Module, FLIR P301-D Wireless Image Transmission Module, P301-D Wireless Image Transmission Module, Image Transmission Module, Transmission Module, Module
Coretronic Intelligent Robotics Corporation SIRASF1E 2A735-SIRASF1E 2A735SIRASF1E sirasf1e
Coretronic Intelligent Robotics Corporation Wireless image transmission module FLIR / P301-D User Manual Product Feature Based on the principle of TDD, key technologies such as OFDM and MIMO are used to improve frequency band utilization Support 64QAM, 16QAM, QPSK, BPSK modulation modes and independent dynamic adjustment of multiple code rates Support AES encryption, support a variety of security policies to prevent illegal monitoring and interception Adopt frequency hopping scheme, monitor the interference situation in real time, and automatically select the frequency hopping range; automatically and quickly change the frequency point and adjust the modulation and coding strategy (MCS) according to the interference situation of the current channel Built-in H.265 encoder, using advanced encoder rate control algorithm, and seamless connection with baseband automatic MCS adjustment, it is more suitable for wireless link transmission under the condition of ensuring image quality P301 D Module Key Specifications category parameter Memory Flash size weight system Power consumption powered by interface temperature range interface wireless transmission delay video transmission delay USB Ethernet CAN UART Interface video video Codec type Codec resolution wireless Maximum transmit power channel bandwidth maximum transfer rate describe 4Gbit DDR4 256Mbit SPI NOR Flash 60mm*35mm*6.5mm(With shield) 20g(Including shield, thermal pad) 2.4G 2T2R transmitter < 7.7W@25dBm 2.4G 1T2R receiver < 3.69W 5.8G 2T2R transmitter < 7.03W@25dBm 5.8G 1T2R receiver < 4.2W DC 5V 60pin*2 B2B Operating temperature-30~55 storage temperature:-40~120 30ms 100ms@1080P60(DVP input -> DVP output) USB 3.0 Host/Device 10/100/1000M adaptive x2 x3 BT.1120/BT.656 24Bit RGB888 MIPI CSI-4 lane H.264 BP/MP/HP encoding and decoding H.265 MAIN/MAIN10 @L5.0 High-tier encoding and decoding MJPEG/JPEG Extended Sequential encoding and decoding H.2641080P@60fps H.2654Kx2K@30fps+1080p@30fps MJPEG/JPEG4Kx2K@30fps 25dBm 2.4GHz 25dBm 5.8GHz 5M/10MHz 60Mbps Sensitivity 2.4G SLOT-100.5dBm BPSK 10M repeat off 2.4G BR-102.5dBm BPSK 5M repeat off 5.8G SLOT-99dBm BPSK 20M repeat off 5.8G BR-109dBm BPSK 5M repeat 2 times Downlink: Automatic channel change frequency Frequency Hopping Scheme point Upstream: Subband Frequency Hopping Maximum transmission distance 15Km (open without interference) Networking method point-to-multipoint chipset AR9201+AR8003S frequency band 2.3~2.7GHz 4.9~5.9GHz Channel Table 7 channels are provided for 2.4GHz@5MHz&10MHz bandwidth 8 channels are provided for 5GHz@5MHz&10MHz bandwidth channel frequency 1 2410MHz 2 2420MHz 3 2430MHz 4 2440MHz 5 2450MHz 6 2460MHz 7 2470MHz channel frequency 36 5180MHz 40 5200MHz 44 5220MHz 48 5240MHz 148 5740MHz 156 5780MHz 160 5800MHz 164 5820MHz P301-D bottom: Size: 60mm x 35mm x7.3mm Install the Hardware The location of P301-D on the remote controller Step1. Put P301 in the slot after opening the housing of remote. Step2. Press down into the slot Step3. locking screw Step.4 Installing the Antenna IPEX Connector Step.5 Installing the heat sink and locking screw Step.6 Install the heat shield Step.7 Combine the upper and lower covers of remote by four screws. ANTENNA LIST This radio transmitter FCC ID: 2A735-SIRASF1E has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna List No. Manufacturer Part No. Antenna Type Peak Gain 1 CIROCOMM 43N15C6V0W0010T Dipole 4.0dBi / 2400~2500MHz 5.0dBi / 5150~5925MHz FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. USERS MANUAL OF THE END PRODUCT In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT The final end product must be labeled in a visible area with the following " Contains FCC ID: 2A735-SIRASF1E ".Adobe PDF Library 17.11.238