Smart Security System User's Guide
DO THIS FIRST.
Things to be Noted Before Getting Started
This guide is for:
- Hub cellular model (Hub 2G model, Hub 4G model)
- Hub cellular + Wi-Fi model (Hub 2G+Wi-Fi model, Hub 4G+Wi-Fi model)
Please check the following conditions for a successful set-up:
- If using a 4G SIM card, ensure the 2G network of your wireless service provider is still available in your country. Purchase the hub with a 4G cellular communicator if the 2G network is unavailable.
The followings are for hub cellular + Wi-Fi model only:
- Select a 2.4GHz Wi-Fi network. The hub does not support the 5GHz Wi-Fi. Selecting the 5GHz band instead of the 2.4GHz band is a common mistake when setting up the hub.
- Your Wi-Fi password must not contain spaces or other special characters.
- Place your hub as close as possible to your router when setting up.
- A slow network speed will affect the hub's performance. An upload speed of at least 2Mbps or faster is recommended.
- Ensure that the AP isolation setting in your router is disabled.
What You Need
To set up and use the Alarm System, you will need an iPhone or Android phone, the Smart Security System app, an unused indoor power outlet, a regular SIM card supporting 2G/GSM (for 2G version) or 4G network (for 4G version), and a Wi-Fi 802.11 b/g/n (2.4GHz) network connection (Hub cellular + Wi-Fi only).
MEET YOUR ALARM SYSTEM.
How the Alarm System Works
The system operates as follows:
- The hub receives a command (e.g., from a remote, RFID tag, ARM button, or the app) and enters "Armed" mode.
- When a Door/Window Sensor detects a door/window opening, it sends a signal to the hub, indicating an intrusion.
- Upon intrusion detection, the hub's internal siren sounds at 85dB on-site, and an optional external siren sounds at 100dB.
- The mobile app notifies you of events at home, anywhere, anytime, via push notifications and text messages. The hub can also make automated phone calls to preset numbers.
- When an optional external wireless siren is installed, it receives a signal from the hub.
Getting to Know Your System
The hub cellular+Wi-Fi model is a dual network system utilizing both Wi-Fi and cellular (GSM/4G). All sensors are wirelessly connected to the hub. In the event of alarm activation, a push notification and an alarm call will be sent automatically to all registered users. The system can be controlled on-site by the supplied remote tag or remotely from anywhere using the dedicated mobile application. The system can connect with up to 100 wireless sensors, 10 remote tags, and 10 RFID tags.
Smart Hub Overview
The Smart Hub is the central unit containing the alarm, display, and keypad.
- Display Window: Shows system status, time, alarm information, menus, and more.
- Speaker: Provides voice prompts and alarm sounds.
- RFID tag reader zone: Tap RFID tags here to arm and disarm.
- Keypad: Features ARM, ARM STAY, DISARM, and DIAL buttons for entering passcodes, settings, and more.
- Tamper switch: (Lever underneath the bracket) Triggers an alarm notification and sound if an attempt is made to remove the hub from its installed location.
- Microphone: For monitoring and two-way talking.
- Regular SIM card slot: For inserting the SIM card.
- Siren port: For connecting the siren cable.
- Backup battery: ON/OFF switch to turn on the built-in backup battery.
- Power port (Type-C): For connecting the power cable.
Hardwired Zone Connections
Zone 1, Zone 2, and Zone 3 are EOLR supervised zones supporting both open and closed circuit devices, with a response time of 300msec. Maximum zone resistance is 11000 ohms, plus EOLR.
Connect closed circuit devices in series on the high (+) side of the loop. The EOL resistor must be connected in series with the devices, following the last device. Connect open circuit devices in parallel across the loop. The 10000-ohm EOLR must be connected across the loop at the last device.
Refer to the Hardwired Zones Connections diagram:
The diagram shows three zones (Z1, Z2, Z3) each connected to GND, with a 10K EOLR resistor. Each zone has normally open (NO) and normally closed (NC) connections.
Important: EOLR (End of Line Resistor): If the EOLR is not at the end of the loop, the zone will not be properly supervised, and the system may not respond to an open circuit on the zone.
Go to Main Menu > Parts > EOL Zone on your hub to set the type and mode of the three wired zones. The number of three zones are set as 100, 101, and 102 by default.
Home Screen and Status Bar
Home Screen
Your home screen may look different if you use another version of the hub.
- Top status bar: Displays time and network status icons.
- Bottom status area: Shows countdown bar, alarm information, and clock.
- Arm/Disarm status: Indicates the current arming state of the system.
Status Bar Icons
| What you see | What it means |
|---|---|
| ? (Cellular network) | No SIM card inserted or SIM card faulty. Shows your carrier's cellular network availability. More bars indicate stronger signal. Bars are gray if not registered with the cellular network. |
| ? (Wi-Fi network) | Shows that the system is connected to a Wi-Fi source and the signal strength (when shown in white). More bars mean stronger connection. |
| ? (Wi-Fi Internet) | Shows that the hub has a Wi-Fi Internet connection when a dot is shown. |
| ✉️ (SMS) | Text message sending. |
| ? (Call) | Calling. |
| ? (Lock keypad) | The keypad is locked. |
| ? (Power) | AC powered; progress bars show charging status. |
| ? (Battery) | Shows the battery level when the system has lost AC power. The icon is red when the backup battery power is low. |
Arm/Disarm Status and Alarm Information
Arm/Disarm Status
Here's the Arm/Home Arm/Disarm status of the system:
| What you see | What it means |
|---|---|
| ? (Away Arm) | System is AWAY ARMED. |
| ? (Home Arm) | System is HOME ARMED. |
| ? (Disarm) | System is DISARMED. |
Alarm Information
Displays what happened in case of alarm.
Countdown bar
Clock is shown without a countdown process.
| What you see | What happens and what you should do |
|---|---|
| Please exit | You now have xx seconds to leave home before the Exit Delay expires. When Exit Delay is completed, the alarm system is armed. |
| Please disarm | You must disarm the system before Entry Delay expires, or an alarm will go off. |
| Synchronizing | You must activate the wireless transmitter to be paired before the pairing delay expires. |
Quick View of Menu Features
Your icons may look different if you use another version of the hub.
| Icon | Item | What you can do with it |
|---|---|---|
| ☰ | Menu | Access system settings. |
| ⚙️ | Settings | Configure system options. |
| ⏱️ | Delay | Adjust delay timers. |
| ?➡️ | Exit Delay | Adjusting Exit Delay (0~65535 seconds, default: 40). |
| ➡️? | Entry Delay | Adjusting Entry Delay (0~65535 seconds, default: 30). |
| ? | Siren Duration | Adjusting Siren Duration (0~65535 minutes, default: 3). |
| ?️ | Switch | Turn on/off features. |
| ? | Arm Beep | Turning arm and disarm beep on or off (default: on). |
| ? | Siren | Turning alarm continuous siren on or off when an alarm occurs (default: on). |
| ✉️ | Arm SMS | Turning SMS notification on or off when the system arms or disarms (default: off). |
| ? | Keypad Lock | Turning touchscreen lock on or off (default: off). |
| ? | Backlight | Turning touchscreen backlight on or off (default: off). |
| ? | Keypad Tone | Turning operation chime on or off (default: on). |
| ⏱️ | Delay Tick | Turning exit and entry chime on or off (default: on). |
| ?️ | Human Voice | Turning Human Voice on or off (default: on). |
| ⚠️ | Door/Window Open Warning | Turning warning notification on or off if you leave a window or door open and arm (default: on). |
| ? | Password | Changing System Code (4 digits, default: 8888). |
| ? | User | Changing User Code (4 digits, default: 1234). |
| ? | Language | Language Selection (default: English). Available languages: 简体中文, English, Deutsch, Русский, Español, Polski, Italiano, Français, Português, Ελληνικά, Română. |
| ? | Initialization | Resetting to factory defaults. |
| ☎️ | Call-Phone Number | Setting the Phone Number for call in case of alarm. |
| ? | SMS-Phone Number | Setting the Phone Number for text message in case of alarm. |
| ? | Log | Alarm Log: Viewing system alarm events. |
| ? | Arm Log | Viewing system arm/disarm events. |
| ? | Parts | Pairing, deleting/editing, deleting all accessories. |
| ? | Remote | Pairing, deleting or deleting all the remote tags. |
| ?️ | Detector | Pairing, editing, deleting or deleting all the wireless sensors. |
| ? | RFID | Pairing, deleting or deleting all the RFID tags. |
| ➕ | Add | Pairing a new remote tag, sensor or RFID tag. |
| ✏️ | Delete/Edit | Deleting a remote tag or RFID tag from the list. |
| ❌ | Delete All | Editing/Deleting a wireless sensor from the list. Deleting all remote tags, sensors or RFID tags. |
| ? | Siren Learn | Sending a transmission signal to the wireless siren be paired. |
| ? | Alarm Socket | Pairing a wireless switch that syncing on/off with the siren. |
| ⏱️ | Socket Timer | Setting a schedule (in 24-hour) for opening/closing wireless switch automatically. |
| ? | Decoder | Read the serial number of detector from its transmitting signal. You can know which wireless accessory were paired in your hub by this tool. |
| ? | Wi-Fi | (Available on hub cellular+Wi-Fi model only) Connecting your hub to the Wi-Fi network and internet by Smart Configuration (Requires the mobile APP). |
| ? | Smartlink Configure | Unbinding the hub link from the server. |
| ? | MAC/IP | Getting the MAC and IP addresses of the Wi-Fi module. |
| ? | SoftAP Configure | Connecting your hub to the Wi-Fi network and internet by Soft AP Configuration (Requires the mobile APP). |
| ? | Record | Recording voice message and playback. |
| ▶️ | Play | Listening to the recorded message. |
| ❌ | Delete | Deleting the recorded message. |
| ⏱️ | Duration | Adjusting Record Duration (1-20 seconds is available). |
| ⏱️ | Timer | Setting a schedule (in 24-hour) for arming automatically. |
| ? | Arm Schedule | Setting a schedule (in 24-hour) for arming automatically. |
| ? | Disarm Schedule | Setting a schedule (in 24-hour) for disarming automatically. |
| ? | Zone&Sync | Reserved. |
| ? | Date&Time | Setting the date and time (in 24-hour). |
| ? | Wi-Fi Sync | Turning using the Wi-Fi network-provided time on or off (hub cellular+Wi-Fi model only). |
| ? | 2G/4G Sync | Turning using the cellular network-provided time on or off. |
| ℹ️ | Version | Getting the firmware and Serial Number of hub, the firmware and IMEI of the GSM module, and MAC address of the Wi-Fi module (hub cellular+Wi-Fi model only). |
Menu Usage Examples
| Item | Caption | Description |
|---|---|---|
| 1 | Exit/Entry Delay | Your security system has been programmed with delay times that allow you to exit the premises after arming, and to disarm the system upon entry before an alarm occurs. If you leave home too late when exiting, or disarm too late when arriving home, it will cause a false alarm. If a false alarm occurs, you should disarm the system immediately. |
| 2 | Arm Beep | When it is turned on, the external siren will beep when armed or disarmed. |
| 3 | Keypad Lock | For additional security, you can require a passcode to unlock the panel. When it is turned on, if you don't operate the keypad on the panel for 30 seconds or so, the home screen locks automatically. |
| 4 | Backlight | When it is turned off, if you don't operate the keypad on the panel for 30 seconds or so, the home screen backlight turns off automatically. |
| 5 | Human Voice | When it is turned on, you'll hear a human voice that tell you what is done. |
| 6 | System Password | Used for keypad unlocking and SMS remote settings. |
| 7 | User Password | Used for keypad unlocking, SMS remote tag and alarm text notification prefixed setting. |
| 8 | Language | Human Voice, Displaying and SMS notification will be in the selected language. After selecting the desired language, the panel will reset accordingly. |
| 9 | Initialization | If the factory default configuration is loaded, any data that has been already programmed into the system will be changed into the factory default configuration! |
GETTING STARTED
Install the SIM Card
Important: A regular SIM card is required to use cellular services when connecting to cellular networks. The availability of cellular capabilities depends on the wireless network.
- Press and slide the cover in the OPEN direction of the arrow and lift it up.
- Plug your SIM card into the cover.
- Put down the cover, press and slide it in the LOCK direction of the arrow to lock it.
Cellular Network Connection
If the ? cellular icon at the top of the home screen turns white, your hub is connected to a cellular network.
Important: If the gray ? icon is always shown, the hub has not connected to a network. Make sure the SIM card has been put in the hub when it was off and the security code of the SIM card is permanently deactivated.
How to Set Phone Numbers for SMS and Phone Calls by Panel
Up to 5 stored Phone Numbers will receive text messages (SMS) and phone calls in case of triggered alarms. The hub will make phone calls to the stored phone numbers successively (up to 2 rounds in turn). If a phone call is answered and any Keypad Command has been operated by one of these users, it will stop calling the next phone number; otherwise, it will continue to remind users until it is up to 2 rounds. When the stored phone calls the hub, two-way talk is connected automatically.
Keypad Commands
| WHICH BUTTON YOU PRESS ON PHONE | WHAT HAPPENS |
|---|---|
| 1 | Arm |
| 2 | Disarm or silence when the alarming is sounding |
| 3 or 4 | Two-way talk |
Go to Menu > Call-Phone Number to set five phone numbers for alarm calls.
Use ⬆️/⬇️ to scroll to the number index to be set, then use the digits keypad to enter the Phone Number (up to 18 digits), tap ↩️ to backspace. The first number will be called first in case of alarm.
Use ⬆️/⬇️ to scroll to 'on'/'off', then tap ⬆️/⬇️ to toggle between 'off' and 'on'. When 'on' is selected, the alarm call will be activated.
Press ✔️ to save your new settings.
Visual representation of Call-Phone Number setup screen shown.
Go to Menu > SMS-Phone Number to set five phone numbers for alarm text messages.
Use ⬆️/⬇️ to scroll to the number index to be set, then use the digits keypad to enter the Phone Number (up to 18 digits), tap ↩️ to backspace. The first number will receive the alarm text message first in case of alarm.
Use ⬆️/⬇️ to scroll to 'on'/'off', then tap ⬆️/⬇️ to toggle between 'off' and 'on'. When 'on' is selected, the Alarm Text Message will be activated.
Press ✔️ to save your new settings.
Visual representation of SMS-PhoneNumber setup screen shown.
Exit / Entry Delay
Entry Delay and Exit Delay are countdowns that allow you to enter and leave your home easily without causing the alarm to sound.
Exit Delay
Exit Delay allows you to leave your home once you've armed the security system. When you place the system into Away Arm Mode, it initiates a countdown to let you know it is preparing to arm. Once the Exit Delay period ends, the system is armed. To provide enough time to exit your home before the countdown ends, you can adjust the timing from 0 (No Exit Delay) to 255 seconds. The default Exit Delay is 40 seconds.
How to change the Exit Delay
Go to Menu > Settings > Delay > Exit Delay and enter to edit the delay value.
Entry Delay
Entry Delay allows you to enter your home and disarm your system while the system is in Away Arm Mode. When you enter your home in Away Arm Mode, your hub initiates a countdown, indicating you have a short time until your alarm sounds. When you hear this, you should disarm your system as soon as possible. You can adjust the countdown timing from 0 (No Entry Delay) to 255 seconds. The default Entry Delay is 30 seconds.
How to change the Entry Delay
Go to Menu > Settings > Delay > Entry Delay and enter to edit the delay value.
How to Record a Voice Message by Panel
Your system can Record/Play/Delete a brief voice message (up to 20 seconds) that can be played back later. The voice message will be played to the remote when an alarm call is connected.
- Go to Menu > Record > and enter.
- Select Record.
- Ready to record when "Recording" is shown, and the system display will count down the remaining recording time.
- Speak into the panel; the recording automatically stops after the time expires.
- The panel plays back the message automatically.
- Press ✔️ to save the message.
Go to Menu > Record > Duration to adjust the record time.
Go to Menu > Record > Play to playback the recorded voice message.
Go to Menu > Record > Delete to delete the recorded voice message.
How to Pair Accessories
How to Pair a Remote Tag by the Panel
Go to Menu > Parts > Remote > Add and enter.
- You need to enter a digit from 0 to 9 to designate a unique number for the remote tag to be paired.
- "Synchronizing" is shown, the hub enters pairing mode and counts down the pairing time remaining.
- Press any button on the remote tag to send a transmission signal to the hub.
- As the serial number of the remote tag is added to the hub, "Leaning OK" will be shown.
Go to Menu > Parts > Remote > Delete to delete the remote tag specified by serial number.
Go to Menu > Parts > Remote > Delete All to delete all remote tags. The total number of paired remote tags is shown before deleting.
How to Pair a Wireless Sensor by Panel (Door/Window Sensor or PIR Motion Detector)
Go to Menu > Parts > Detector > Add and enter.
- Scroll to ⬆️/⬇️ and tap to select the desired Zone Name. To be used as a doorbell, select "Doorbell".
- Scroll to ⬆️/⬇️ and tap to select the desired Zone Mode (Type). You must assign a Zone Mode to each zone (sensor), which defines how the system responds to faults in that zone:
- Normal: Sensors set to Normal Zone are activated in Arm (full arm) or HOME Mode (stay/partial arm). Recommended for door/window sensors.
- 24 Hours: Sensors set to 24H Zone will activate the alarm and sound when triggered, regardless of the alarm status (Armed or Disarmed).
- Delay: If sensors set to Delay Zone are triggered, the Hub will sound the alarm after the delay time has passed. Recommended for door sensors used as primary entryways.
- Home: Sensors set to Home Zone are only activated in Arm (full arm). If Stay Arm Mode (partial/home arm) is used, these sensors are not armed and will not activate the alarm if triggered. Recommended for PIR Motion Detectors.
- 24 Hours Silent: The mode is the same as 24H but without sound.
- To disable the zone, select Close.
- Scroll to ⬆️/⬇️ using the digits keypad to enter the Zone Number (0-89 are available), tap ↩️ to backspace. The Zone Number must be unique if more than one sensor needs to be paired.
- Select ✔️. "Synchronizing" is shown, the panel enters pairing mode and counts down the pairing time remaining.
- Trigger the wireless sensor to send a transmission signal to the panel.
- As the serial number of the wireless sensor is added to the panel, "Leaning OK" will be shown.
- The setup screen shows options for Set Name/Mode/Number, with examples like PIR, 24h Normal (without delay), and Zone Number 1.
Go to Menu > Parts > Detector > Edit to edit the Zone Name/Zone Mode of a selected zone by its number, or delete the selected zone.
Go to Menu > Parts > Detector > Delete All to delete all wireless sensors. The total number of paired sensors is shown before deleting.
How to Pair a RFID Tag by Panel
Go to Menu > Parts > RFID > Add and enter.
- You need to enter a digit from 0 to 9 to designate a unique number for the RFID tag to be paired.
- "Synchronizing" is shown, the panel enters pairing mode and counts down the pairing time remaining.
- Tap the RFID Tag on the RFID read zone of your panel.
- As the serial number of the RFID Tag is added to the hub, "Leaning OK" will be shown.
Go to Menu > Parts > RFID > Delete to delete the RFID Tag specified by serial number.
Go to Menu > Parts > RFID > Delete All to delete all RFID Tags. The total number of paired tags is shown before deleting.
How to Pair a Wireless Siren by Panel
Go to Menu > Parts > Siren Learn.
- Press and hold the SET button of the siren until you hear two beeps, then the siren enters sniffer mode and the light ring blinks quickly.
- Press the ✔️ button on the panel within 6 seconds. The panel shows "Learn Signal Sent" and sends a transmission signal to the siren.
- The siren gives four beeps for successful indication.
APP
Download App
Scan the QR codes or find "TuyaSmart" on the App Store or Google Play to get the free APP. (Visuals of QR codes for TuyaSmart app are described here). Your App may look different if you purchased a different hub model.
APP for Hub Cellular Model
For the hub cellular model, you can arm, stay arm, and disarm your system by sending text messages using the APP. You can also name your accessories, set Phone Numbers, Change Exit/Entry Delay, or Enable/Disable features, and more via the APP.
APP for Hub Cellular + Wi-Fi Model
Special Tips: After installing the app, the phone will request permission to receive notifications from the APP. Forbidden to receive notifications may result in an application running failure.
USING SMART SECURITY SYSTEM.
The Security Levels
Smart Hub has three different security levels for when you're home or away. You can easily switch between them on the Smart Hub, with an RFID tag, remote tag, or the app.
| Security Level | Use When | What You Hear | What Happens | What's Detected | Notifications and Calls |
|---|---|---|---|---|---|
| Away Arm ? | No one is home. | "Please input password" "System Armed" | The alarm sounds when a door or window opens, or when there's motion in a room. | Motion: ✔️ Open: ✔️ | ✔️ |
| Home Arm ? | You're home and want security. | "Please input password" "System Armed" | The alarm sounds when a door or window opens. | Motion: - Open: ✔️ | ✔️ |
| Disarm ? | You don't want security. | "System Disarmed" | The alarm won't sound. | Motion: - Open: - | - |
Away Mode: All sensors in your home are monitored. This is useful when you're going out and want to be notified if anything happens to your home.
Home Mode: All NORMAL and DELAY (exterior and perimeter) sensors are monitored, but interior sensors are not monitored. This is useful if you're at home but want to be alerted if anyone tries to break in through a door or window.
Disarmed Mode: No sensors but 24 HOUR sensors in your home are monitored. This is useful when you're at home and want the freedom to go in and out easily.
How to Arm and Disarm
You can arm and disarm your home in three ways: entering your passcode on the panel (if locked), pressing the Arm/Stay Arm/Disarm icons, tapping an RFID Tag on the panel, or using the remote tag or app. When you hear the panel's chime alert, the screen will show a countdown indicating how much time you have before the alarm sounds.
No Rush
With "No Rush", you can take the time you need to leave home or disarm before the alarm sounds. By default, you have 40 seconds.
To adjust the countdown timing, go to Menu > Settings > Delay > Exit Delay/Entry Delay. (See Exit/Entry Delay description).
Auto Schedule
You can set an arm schedule and a disarm schedule to arm or disarm the system automatically at a daily time.
- Go to Menu > Timer > Arm Schedule/Disarm Schedule and enter.
- Scroll to ⬆️/⬇️ and enter the Daily Arm/Disarm time (in 24-hr), tap ↩️ to backspace.
- Scroll to ⬆️/⬇️ and tap ⬆️/⬇️ to toggle 'on' to enable the schedule.
- Press ✔️ to save your schedule.
Visual representation of Arm Schedule setup screen shown (e.g., 20:12, on).
Make a Call on Panel
On the home screen, tap one of the digits to enter the dialing screen, enter the number, then tap ✔️ to dial.
Important: The call will be cancelled if the cellular network is not registered, the system is armed, or in voice alarming.
Smart Hub Features
Battery backup
If the building loses electrical power, Smart Hub includes a backup battery that will last for more than 3 hours. Even if the power is out, Smart Hub can still detect an intruder and sound the alarm. The battery icon in the upper-right corner shows the battery level or charging status (for reference). If the backup battery is very low, the icon turns red. Low Battery notifications will be sent to registered phone numbers. The battery is fully charged within 8 to 12 hours.
Loss/Restoration of AC power
If AC power is lost or restored, the hub will send an alert notification to let you know.
Tamper detection
If someone tampers with Smart Hub and removes it from the back plate, the hub will send an alert notification to let you know.
RESET TO FACTORY SETTINGS
Go to Menu > Settings > Initialization > and enter.
Important: You won't be able to reset if Smart Hub is locked. All paired accessories and event logs will be deleted when reset is done.
SPECIFICATIONS
Hub
| Parameter | Value |
|---|---|
| Power Supply | Micro USB 110/220VAC to 5V, 1000mA |
| Backup Battery | 3.7V, 500mAh Rechargeable Lithium Battery |
| Consumption | <55mA |
| Radio Frequency | 433Mhz |
| GSM | 850/900/1800/1900MHz |
| Wi-Fi | IEEE802.11b/g/n |
| Operation Temperature | 0~55℃ |
Remote
| Parameter | Value |
|---|---|
| Power Supply | 12V27A (contain) / CR2032 3V (contain) |
| Standby Current | <5uA |
| Alarm Current | <15mA |
| Transmitting Distance | <80m (Open Area and No Interference) |
| Radio Frequency | 433Mhz |
| Operation Temperature | 0~55℃ |
Door/Window Sensor
| Parameter | Value |
|---|---|
| Power Supply | CR2032 3V (excluding) / 12V23A (excluding) |
| Standby Current | <8uA |
| Alarm Current | <15mA |
| Transmitting Distance | <80m (Open Area/No Interference) |
| Radio Frequency | 433Mhz |
| Operation Temperature | 0~55℃ |
PIR Motion Sensor
| Parameter | Value |
|---|---|
| Power Supply | 2*AA battery (excluding) / 9V battery (excluding) |
| Standby Current | <15uA |
| Alarm Current | <25mA |
| Detection Scope | <12m/110° |
| Transmitting Distance | <80m (Open Area and No Interference) |
| Radio Frequency | 433Mhz |
| Operation Temperature | 0~55℃ |
RFID Tag
| Parameter | Value |
|---|---|
| Chip | 4100/4200 |
| Frequency | 125KHz |
| Read Distance | <2cm |
ADDING YOUR HUB
Smartlink Configuration
- Tap Add Device or "+", select Security & Sensor and tap Alarm.
- On your hub, tap ⬆️/⬇️ to go to Wi-Fi > Smartlink Configure. Ensure your device is in SmartLink mode with the LED blinking rapidly.
- Tap "Confirm indicator rapidly blink", choose your local Wi-Fi and input the password (Only 2.4Ghz Wi-Fi network is supported).
- Wait for the configuration to finish, then tap Done.
SoftAP Mode
- Please change to Soft AP mode if the configuration fails in SmartLink mode.
- Tap AP Mode on the Add Device page.
- On your hub, tap ⬆️/⬇️ to go to Wi-Fi > SoftAP Configure. Ensure your device is in SoftAP mode with the LED blinking slowly.
- Tap "Confirm indicator slowly blink" on your APP, choose your local Wi-Fi and input the password (Only 2.4Ghz Wi-Fi network is supported).
- Tap Confirm > Go to Connect, then choose the Wi-Fi hotspot named "Smartlife-XXXX" in your Wi-Fi list. Go back to your APP to wait for the Wi-Fi configuration to finish, then tap Done.
Tips: After the configuration is done, you might tap ➡️? to Share Device with your family.
HOW TO ADD PHONE NUMBER
- Tap Setting > Alarm call number in the Contact column to add phone numbers for alarm calls.
- Tap Setting > Alarm SMS number in the Contact column to add phone numbers for alarm SMS.
- Tap Alarm call to turn alarm call on or off.
- Tap Alarm SMS to turn alarm SMS on or off.
Tips: Up to 5 alarm call numbers and 5 alarm SMS numbers can be added.
HOW TO ADD ACCESSORY
Pick your device at the home page, tap Accessories > Add, then follow the tips below to trigger your accessory to be added (After the accessory is added, it will be classified into its corresponding column automatically).
Tips: Up to 100 wireless detectors, 10 remote tags, and 10 RFID can be added.
EXIT / ENTRY DELAY
Change Delay Value
Tap Exit delay or Entry delay to change the delay time.
Tips: Default exit delay is 40 seconds and entry delay is 30 seconds.
HOW TO ARM/DISARM
- Tap ➡️ to Away arm.
- Tap ? to Home arm.
- Tap ? to Disarm.
- Tap ? to trigger an emergency alarm.
Tips: Tap Setting > Timer to arm/disarm your system on schedule.