STEGO LED Cabinet Lights: Type LED 021, 121, 022, 122 Quick Start Guide

Warnings

⚠️ **WARNING:** There is a risk of personal injury and equipment damage if the connection values are not observed or polarity is incorrect!

Product Overview

This document describes the STEGO Type LED 021 / 121 / 022 / 122 series of LED lights designed for illumination in stationary, closed electrical cabinets.

Models and Specifications

• LED 021: Length 375mm, 30 LEDs, 120° beam angle, 6500K, 1080 Lumens, 60,000h lifespan, 0.2kg.
• LED 021 (with motion detector): Length 375mm, 30 LEDs, 120° beam angle, 6500K, 1080 Lumens, 60,000h lifespan, 0.2kg.
• LED 121: Length 475mm, 30 LEDs, 120° beam angle, 6500K, 1080 Lumens, 60,000h lifespan, 0.3kg.
• LED 121 (with motion detector): Length 475mm, 30 LEDs, 120° beam angle, 6500K, 1080 Lumens, 60,000h lifespan, 0.3kg.
• LED 022: Length 575mm, 48 LEDs, 120° beam angle, 6500K, 1730 Lumens, 60,000h lifespan, 0.3kg.
• LED 022 (with motion detector): Length 575mm, 48 LEDs, 120° beam angle, 6500K, 1730 Lumens, 60,000h lifespan, 0.3kg.
• LED 122: Length 675mm, 48 LEDs, 120° beam angle, 6500K, 1730 Lumens, 60,000h lifespan, 0.4kg.
• LED 122 (with motion detector): Length 675mm, 48 LEDs, 120° beam angle, 6500K, 1730 Lumens, 60,000h lifespan, 0.4kg.

Accessories

• Door switch (grey plug)
• Power connection (white plug)

Technical Data

Electrical Specifications

• LED 021/022: AC 100V - 240V (min. AC 90V, max. AC 265V)
• LED 121/122: AC 220V-240V, 50/60Hz; AC 120V 50/60Hz

Environmental Conditions

• Operating Temperature: -30°C to +40°C (-22°F to +104°F)
• Maximum Humidity: 90% RH

Mounting

• Screw mounting: M5/M6 screws, recommended torque 2 Nm.
• Main mounting torque: 35 Nm.

Ingress Protection

• IP20

Installation and Usage

Application

The light is used for illumination in stationary, closed electrical cabinets according to DIN EN 61439-1/DIN EN 61439-2.

Safety Considerations

• Installation must only be performed by qualified electrical technicians, observing national power-supply guidelines (IEC 60364).
• For lamps with magnetic fixing, verify the magnet's holding power is adequate for the application with the connection cable.
• The lamp must be mounted stationary.
• With magnetic fixing, the lamp can be flexibly mounted in the electrical cabinet.
• Strictly observe the technical specifications on the type plate.
• No changes or modifications are permitted on the device.
• In case of apparent damage or malfunction, do not repair or operate the device. Dispose of the device.
• The light source is not replaceable.
• The lamp must not be used as a hand lamp.
• The lamp must not be used for household lighting.

Commissioning the Lamp with Motion Detector

The test run is activated by disconnecting from mains and then reconnecting. The lamp flashes briefly twice and then switches off again. Upon reactivation of the motion detector, the lamp switches on for 5 seconds and then switches off again; the lamp is ready for operation.

Notice

The manufacturer accepts no liability in the case of failure to observe this brief instruction, improper use, changes, or damage to the device.