Product Description
The MWB1830-WB01 is a high-gain, low-power consumption Wi-Fi module that fully complies with IEEE 802.11b/g/n standards. It offers feature-rich wireless connectivity, delivering reliable, cost-effective throughput over extended distances. The module operates when connected to 5V, UART, and GND. The Bluetooth component supports the latest 5.1LE operation.
Product Features
- Complies with IEEE 802.11g, 802.11b, and 802.11n standards for 2.4GHz Wireless LAN.
- Features a single transmit and single receive path (1T1R).
- Supports Ad-Hoc and Infrastructure modes.
- Works with all existing network infrastructure.
- Capable of up to 128-Bit WEP Encryption.
- Allows freedom to roam while staying connected.
- Achieves up to 75.5Mbps High-Speed Transfer Rate in 802.11N mode.
- Supports Linux Operating Systems.
- Offers low power consumption.
- Complies with UART base specification revision 1.1 for WLAN.
- Easy to install and configure.
- Features Bluetooth v5.1 Low Energy (LE).
Product Specification
| Specification | Details |
|---|---|
| Model | MWB1830-WB01 |
| Product Name | WIFI+BT Module |
| Standard | 802.11a/b/g/n |
| Interface | WiFi: UART, BT: UART |
| Data Transfer Rate | 1, 2, 5.5, 6, 11, 12, 18, 22, 24, 30, 36, 48, 54, 60, 90 Mbps and maximum of 75.5Mbps |
| Modulation Method | QPSK, BPSK, CCK (802.11b) QPSK, BPSK, 16QAM, 64QAM with OFDM (802.11g) BPSK, QPSK, 16QAM, 64QAM with OFDM (802.11n) GFSK (BT) |
| Frequency Band | 2.4GHz: CH 1~CH11 for FCC |
| Transmit Power | < 20dBm |
| Operation Mode | Ad hoc, Infrastructure |
| Operation Range | Up to 150 meters in open space |
| OS Support | AliOS |
| Security | WEP, TKIP, AES, WPA, WPA2 |
| Operating Voltage | 5V ± 10% |
| Operating Temperature | -40 ~ 85°C ambient temperature |
| Storage Temperature | -40 ~ 125°C ambient temperature |
| Humidity | 5 to 95% maximum (non-condensing) |
Pin Definitions
| Pin Name | Functional Description |
|---|---|
| GND | Ground |
| TX | UART-TX, receive end in UART download |
| RX | UART-RX, transmit end in UART download, floating or pull up |
| 5V | 5V power supply |
PCB Antenna Specifications
A photograph shows the MWB1830-WB01 module, a small printed circuit board with various electronic components.
The PCB antenna is a 2.4G type with a gain of 2.42 dBi. It is permanently attached to the module and cannot be replaced.
Diagram Description: A diagram illustrates the dimensions of the PCB antenna. It shows a serpentine trace pattern with specific measurements in millimeters for length, width, and spacing, indicating a 2.4GHz antenna. Key dimensions shown are approximately: 14.50mm length, 5.40mm height, with various internal trace widths and spacings like 2.30mm, 4.80mm, 7.00mm, 9.50mm, 11.70mm, 13.80mm, and small gaps of 0.50mm and 0.90mm.
Notices
- Please keep this product and accessories away from children's reach.
- Do not splash water or other liquids onto this product, as it may cause damage.
- Avoid placing this product near heat sources or direct sunlight, which could cause deformation or malfunction.
- Keep this product away from flammable materials or open flames.
- Do not attempt to repair this product yourself. Only qualified personnel should perform repairs.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
If the FCC identification number is not visible when the module is installed inside another device, the exterior of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as: "Contains FCC ID: VG8MWBWB01" or any similar wording that conveys the same meaning.
The module can only be installed or integrated into mobile or fixed devices. It cannot be installed in any portable device, such as USB dongle transmitters.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The transmitter must not be co-located or operating in conjunction with any other antenna or transmitter and must be installed to provide a separation distance of at least 20cm from all persons.
A separate approval is required for all other operating configurations, including portable configurations, with respect to Part 2.1093 and different antenna configurations. The grantee must provide guidance to the host manufacturer for compliance with Part 15B requirements.
The end-user manual must include all required regulatory information/warnings as shown in this manual. This product must be installed and operated with a minimum distance of 20 cm between the radiator and the user's body.
The module complies with FCC Part 15.247 / RSS-247 and applies for Single Module Approval.
Canada Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
The device has been tested for compliance with SAR limits. Users can obtain Canadian information on RF exposure and compliance.
If the ISED certification number is not visible when the module is installed inside another device, the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as: "Contains IC: 21015-MWBWB01" or any similar wording that expresses the same meaning.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter and must be installed to provide a separation distance of at least 20cm from all persons.
The module can only be installed or integrated into mobile or fixed devices. It cannot be installed in any portable device, for example, USB dongle like transmitters is forbidden.
The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product.