Keychron K10 Max Wireless Mechanical Keyboard
USER MANUAL
Fully Assembled Version
Keyboard
- 1x Fully Assembled Keyboard
- Including
- 1x Case
- 1x PCB
- 1x Steel Plate
- 1x Sound Absorbing Foam
- 1x IXPE Foam
- 1x PET Film
- 1x EPDM Foam
- 1x Bottom Case PET Film
- 1x Silicone Bottom Pad
- 8 Sets x Stabilizers
- 1 Set x Keycaps (PBT Double-shot)
- 1 Set x Switches
Cable
- 1x Type-A to Type-C Cable
Receiver
- 1x Type-A 2.4GHz Receiver
- 1x Extension Adapter For Receiver
Tools
- 1x Keycap & Switch Puller
- 1x Screwdriver
- 1x Hex Key
Barebone Version
Keyboard Kit
- 1x Keyboard Kit (Without Keycaps & Switches) Including
- 1x Case
- 1x PCB
- 1x Steel Plate
- 1x Sound Absorbing Foam
- 1x IXPE Foam
- 1x PET Film
- 1x EPDM Foam
- 1x Bottom Case PET Film
- 1x Silicone Bottom Pad
- 8 Sets x Stabilizers
Cable
- 1x Type-A to Type-C Cable
Receiver
- 1x Type-A 2.4GHz Receiver
- 1x Extension Adapter For Receiver
Tools
- 1x Keycap & Switch Puller
- 1x Screwdriver
- 1x Hex Key
QUICK START GUIDE
If you are a Windows user, please find the appropriate keycaps in the box,then follow the instructions below to find and replace the following keycaps.
1. Connect 2.4GHz Receiver
Note: For the best wireless experience, we recommend using the extension adapter for receiver and putting the 2.4GHz receiver somewhere on your desk close to your keyboard for a low rate of latency and fewer signal interferences.
2. Connect Bluetooth
Press fn + 1 (for 4 seconds) and pair with device named Keychron KlO Max.
3. Connect Cable
4. Switch To The Right System
Please make sure the system toggle on the top left corner has been switched to the same system as your computer’s operating system.
5. The Backlight
6. Adjust The Backlight Brightness
7. Adjust The Backlight Speed
8. The Keychron Launcher App
Please visit launcher.keychron.com to access the Keychron online launcher app. This app enables users to remap keys, adjust key actuation points, assign multiple commands to a single key, enter game controller mode, and more.
If it cannot recognize your keyboard, please reach our support to get instruction.
‘The online launcher App can only run on the latest version of Chrome, Edge, and Opera browsers yet. ‘The online launcher App only works when the keyboard is connected by wire to the computer.
9. The Layers
There are four layers of key settings on the keyboard. The layer O and layer 1 are for the Mac system. The layer 2 and layer 3 are for the Windows system.
If your system toggle is switched to Mac, then the layer O will be activated.
If your system toggle is switched to Windows, then the layer 2 will be activated. Remember that if you are using it in Windows mode, please make changes to the layer 2 instead of the top layer (the layer 0). This is a common mistake people are making.
10. Factory Reset & Firmware Update
Troubleshooting? Don’t know what’s going on with the keyboard?
Factory reset your keyboard
1. Power on your keyboard.
2. Press and hold In + J + Z (for 4 seconds). The keyboard backlight will flash in red quickly for 3 seconds, indicating that the keyboard has been reset.
Flash your keyboard firmware
1. Visit launcher.keychron.com to open the online Launcher web app.
2. Ensure the keyboard is in Cable or Wired mode and plug in the power cable.
3. Find the ‘Firmware Update’ tab on the left side of the Launcher and connect your keyboard with it.
4. Follow the instructions on the Launcher and complete the firmware update.
*Step-by-step guide, search the keyword “firmware” on keychron.com.
The keyboard is highy customizable and easy to be rebuilt.
If anything goes wrong with any of the keyboard components of keyboard during the warranty period, we will only replace the defective parts of the keyboard, not the whole keyboard.
K10 MAX WIRELESS MECHANICAL KEYBOARD SPECIFICATIONS
- Number of keys: 108
- Switch type: Mechanical
- Battery: 4000mAh
- Charging time: Around 5 hours
- Charging port: Type-C
- Mode: Bluetooth / Wired / 2.4GHz
- Bluetooth operating distance: Within 10 meters (open space)
- Name of Bluetooth device: Keychron K10 Max
LED STATUS OVERVIEW
K10 MAX WIRELESS MECHANICAL KEYBOARD OVERVIEW
1. Power Indicator
2. Bluetooth / 2.4GHz Indicator
3. Caps Lock Indicator
4. Type-CPort
5. Win/Android Mac/iOS(OS Toggle)
6. 2.4G I Cable / BT (Connection Mode Toggle)
DEFAULT KEY LAYOUT:
LAYER 0: This layer will be activated when your keyboard’s system toggle is switched to Mac.
LAYER 1: This layer will be activated when your keyboard’s system toggle is switched to Mac and press the fn/M0(1) key.
LAYER 2: This layer will be activated when your keyboard’s system toggle is switched to Windows.
LWin = Left Windows LAlt = Left Alt RAlt = Right Alt RCtl = Right Ctrl RWin= Right Windows
LAYER 3: This layer will be activated when your keyboard’s system toggle is switched to Windows and press the fn/M0(3) key.
KEY DESCRIPTION
FUNCTION DESCRIPTION:
CHARGING
Plug the cable into a USB port and plug the other end into the keyboard port. Power Indicator:
A red light will stay on while charging; Fully charged in around 5 hours, a green battery indicator will appear.
*The K10 Max keyboard is compatible with all USB ports. Please use a SV 1A adapter or USB 3.0 for the best performance. The K10 Max can be charged in 2.4GHz/Cable/Bluetooth mode.
**This product supports up to SV charging voltage and 1A charging current. We are not responsible for any problems caused by improper charging.
2.4GHz I CABLE/ BLUETOOTH MODE (MODE TOGGLE)
2.4GHZMODE
1. Connect the 2.4GHz receiver to your device’s USB Port.
2. Switch the toggle to the 2.4GHz option. The keyboard will automatically connect to your device.
BWETOOTH MODE
1. Switch the toggle to the Bluetooth option.
2. Backlighting will be turned on.
3. Hold “fn+1” key for 4 seconds to activate Bluetooth pairing (the Bluetooth indicator fast flashes for 3 minutes to detect pairing).
4. Search for the Bluetooth device “Keychron K10 Max” on your device and connect it (the Bluetooth indicator goes off after successful pairing).
Note: This keyboard supports pairing up to 3 devices simultaneously via key combination “fn” + “1” I “fn” + “2” I “fn” + “3”.
*The Bluetooth indicator will continue to flash for 3 minutes.
**Slow or failed connections may exist due to different Bluetooth versions, please make sure all the settings are correct.
SWITCH BLUETOOTH DEVICES
Short press key combination “fn” + “1” I “fn” + “2” I “fn” + “3” to switch to other device.
RECONNECT:
1. Switch the keyboard to the Bluetooth option to activate the keyboard.
2. The Bluetooth indicator flashes for 3 seconds and automatically pairs with the last paired device.
3. If the Bluetooth indicator is off, press any button to enter the connection again.
* The keyboard must have been paired with the device to perform this function.
WIRED MODE
1. Switch the toggle to the Cable option .
2. Connect our cable with your PC and keyboard.
3. Backlighting will be turned on.
*Under Wired Mode, keyboard will not enter into Battery Saver Mode.
TURN OFF THE KEYBOARD
Switch the keyboard to the Cable option and unplug the power cable.
Safety Precaution:
Keep the product, accessories and packaging parts out of the reach of children to prevent any accidents and choking hazards.
Always keep the product dry to avoid corrosion.
Do not expose the product to extreme temperatures below -10°C(14° F) or above 50°C(122° F) to preserve the lifespan of the keyboard.
Keychron, Inc.
Dover, DE 19901, United States
Find us at:
https://www.keychron.com
Support@keychron.com
l)@keychron
@@keychron
X@keychronMK
Designed by Keychron
Made in China
Documents / Resources
 | Keychron K10 Max Wireless Mechanical Keyboard [pdf] User Manual K10 Max, K10 Max Wireless Mechanical Keyboard, Wireless Mechanical Keyboard, Mechanical Keyboard, Keyboard |
