Intelligent Mesh Network Devices DH-19 SPP Bluetooth USB Dongle User Manual DESCRIPTION SPP Bluetooth USB Dongle OPERATING Power…
Suppliers of articles for use at work are required under section 6 of the Health and Safety at Work Act 1974 to ensure as reasonably as is practical that the article will be safe and without risk to health when properly used.
An article is not regarded as properly used if it is used ‘without regard to any relevant information or advice’ relating to its use made available by the supplier.
This product should be installed, commissioned and maintained by trained service personnel in accordance with the following:
Installers of this product are required to take such steps as necessary to ensure that all appropriate information and training is provided to anyone concerned with its use.
This equipment is designed to operate at a DC voltage of 18-36V and therefore will require a separate power supply.
Any power supplies used with this equipment must be suitably approved to the required local standards and must be installed following the relevant electrical, installation standards and manufacturers’ recommendations.
This unit should be built into an apparatus cabinet, or similar, where access is restricted to service personnel only.
This unit uses convection cooling. Avoid obstructing the airflow around the unit.
This equipment is certified as environmental class A and therefore designed for indoor use only at temperatures between -10°C and +70°C with a maximum relative humidity of 95%. The IP rating for the enclosure is IP20
Operation outside of these limits may render the equipment unsafe.
This Start Guide provides iNS module connection/settings overview and links to the product range User Guides.
Important! Information in this Start Guide is supplementary.
The product Installation Manual and Operation Manual should read, understood and referred to throughout.
The QR codes below provide links to iNS User Manuals. Using your Smartphone, tablet or device (where necessary) install a third party QR Code Reader and scan the code to open the documents.
Reading the QR Codes
Should you be unable to work with QR codes Manuals can be obtained by visiting the following website pages:
|DNX-A-2R-K User Guide||http://www.kentec.co.uk/manuals/man-1491.pdf|
|DNP-R-2F/FC-K User Guide||http://www.kentec.co.uk/manuals/man-1572.pdf|
DNX-A-2R-K Dual Port Fire Alarm Control Panel Connections & Selection Settings
DNP-R-2F/FC-K Dual Port Fire Alarm Control Panel Fibre Connections & Passive Mode Settings
DNP-R-2F/FC-K Dual Port Fire Alarm Control Panel Fibre/RS485 Connections & Selection Settings
Details of Kentec Electronics Ltd. Terms and Conditions including Warranties and Returns & Repair Policies can be found on our website at the following locations:
Terms, Conditions & Warranty https://kentec.co.uk/terms-and-conditions/
Returns & Repairs http://www.kentec.co.uk/returns-and-repairs/
Address of Kentec Electronics Ltd.
Units 25-26 Fawkes Avenue,
Kent. DA1 1JQ
Registered in England: FACP
Tel: +44 (0)1322 222121
In no event shall The Manufacturer be liable for any damages or injury of any nature or kind, no matter how caused, that arise from the use of the equipment referred to in this manual. Strict compliance with the safety procedures set out and referred to in this manual, and extreme care in the handling or use of the equipment, are essential to avoid or minimize the chance of personal injury or damage to the equipment. The information, figures, illustrations, tables, specifications, and schematics contained in this manual are believed to be correct and accurate as at the date of publication or revision. However, no representation or warranty with respect to such correctness or accuracy is given or implied and The Manufacturer will not, under any circumstances, be liable to any person or corporation for any loss or damages incurred in connection with the use of this manual.
The information, figures, illustrations, tables, specifications, and schematics contained in this manual are subject to change without notice. Unauthorized modifications to the fire detection system or its installation are not permitted, as these may give rise to unacceptable health and safety hazards. By installing this equipment on a computer network, the owner accepts full and unequivocal responsibility for ensuring that it is protected against all cyber threats and illegal tampering during the lifetime of the equipment. Any software forming part of this equipment should be used only for the purposes for which The Company supplied it. The user shall undertake no changes, modifications, conversions, translations into another computer language, or copies (except for a nec-essary backup copy). In no event shall The Manufacturer be liable for any equipment malfunction or damages whatsoever, includ-ing (without limitation) incidental, direct, indirect, special, and consequential damages, damages for loss of business profits, business interruption, loss of business information, or other pecuniary loss, resulting from any violation of the above prohibitions.
|Kentec Electronics DNX-A-2R-K Intelligent Network Solutions [pdf] User Guide|
DNX-A-2R-K, DNP-R-2F, FC-K, DNX-A-2R-K, Intelligent Network Solutions, DNX-A-2R-K Intelligent Network Solutions
PA4G Single Packaged Air Conditioner System with R-410A Refrigerant PA4G 13.4 SEER2 Single and Three…
38 Inchs (97 cm) Fitness Trampoline Owner's Manual. Fitness Trampoline 38" (97 cm) www.viavito.com 02…
Lithium Series Dual 48V 5.1kWh Solis Inverter QUICK INSTALLATION GUIDE Lithium Series Dual 48V 5.1kWh…
BNR1839 Electric Drywall Sander Interchangeable Operating Instructions BNR1839 Drywall Sanding Machine Please read this manual…