KAISAI Wired Controller
Specifications
- Product: Wired Controller
- Input Voltage: Operating voltage
- Operating Temperature: Suitable operating temperatures
- Humidity: RH9002%
- WIFI Information: WIFI transmission frequency range – 2.400~2.4835 GHz EIRP 20 dBm
General Safety Precautions
This document is applicable only to the wired controller. Read this document and follow the instructions carefully before operating the wired controller. Always observe all the operating instructions. Hand these instructions and all other applicable documents to the end user.
Safety Signs
WARNING: It indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.
NOTE: Additional information.
Notice to Users
If you are not sure how to operate the unit, contact your installer.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge provided that they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and maintenance shall not be made by children without supervision.
Documentation
This document is part of a documentation set. The complete set consists of:
- Installation Manual: Brief installation instructions (paper included with the outdoor unit)
- Operation Manual: Quick guide for basic usage (paper included with the outdoor unit)
- Technical Data Manual: Performance data and ERP information (paper included with the outdoor unit)
FAQs
Q: What should I do if I encounter an error with the wired controller?
A: If you encounter an error, refer to the Error Info section in the manual for troubleshooting steps. If the issue persists, contact your installer or local authority for assistance.
Q: Can children operate the wired controller?
A: Children aged 8 years and above can operate the appliance under supervision or instruction. It is important to ensure that children do not play with the appliance and that cleaning and maintenance are carried out by adults.
GENERAL SAFETY PRECAUTIONS
This document is applicable only to the wired controller. Read this document and follow the instructions carefully before operating the wired controller. Always observe all the operating instructions. Hand these instructions and all other applicable documents to the end user.
WARNING
Follow the safety precautions in the INSTALLATION MANUAL for the correct use of the heat pump unit.
1.1 Safety Signs
Action-related warnings in the document:
WARNING
It indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.
NOTE
Additional information.
1.2 Notice to Users
If you are not sure how to operate the unit, contact your installer.
6
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge provided that they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and maintenance shall not be made by children without supervision.
The unit is marked with the following symbol:
This means that electrical and electronic products may not be mixed with unsorted household waste. Do not try to dismantle the system yourself. The dismantling of the system and the treatment of the refrigerant, oil and other parts must be done by an authorized installer and must comply with applicable legislation.
The unit must be treated at a specialized treatment facility for reuse, recycling and recovery. By ensuring this product is disposed of correctly, you will help to prevent potential negative consequences for the environment and human health. For more information, contact your installer or local authority.
Working conditions of the wired controller.
Input voltage Operating temperature
12V DC -10 to 43°C
Humidity
RH9002%
7
Troubleshooting of networking failures When connecting the product to a network, please keep the product as close to your phone as possible. At present, the product only supports 2.4 GHz band routers. Special characters, such as punctuation and space, are not recommended as a part of the WLAN name. The number of devices connecting to the same router should not exceed 10. Otherwise, the devices may be disconnected due to unstable signals. If the password of the router or WLAN is changed, clear all settings and reset the appliance. The contents of APP might change in version updates and actual operation shall prevail.
WIFI information WIFI transmission frequency range: 2.400~2.4835 GHz EIRP 20 dBm
8
2 DOCUMENTATION
Scan the QR code on the right for other languages.
This document is part of a documentation set. The complete set consists of:
Installation Manual Brief installation instructions Format: paper (included with the outdoor unit)
Operation Manual (this manual) Quick guide for basic usage Format: paper (included with the outdoor unit)
Technical Data Manual Performance data and ERP information Format: paper (included with the outdoor unit)
Online Tools (APP) APP: scan the QR code on the right or in the front page to download the app
Scan the QR code to read the manual in different languages
Scan the QR code to install the control APP.
9
3 USER INTERFACE
3.1 Names and Functions
Zone1
Icon
Name
Menu/Return*
Definition
Press to access the menu page (from the home page) / return to the previous page (from a page other then the home page)
Confirm
Confirm a selection / Save settings / Acess the next page
ON/OFF
Turn on/off zone 1/zone 2/DHW Press and hold for 3 seconds to turn on/off all appliances (zone 1 / zone 2 / DHW).
Navigation:
Press to navigate the cursor to adjust
upward, downward settings (holding it for 1 second can
leftward, rightward start quick adjustment)
* Hold for 2 seconds to return to the main page.
10
3.2 Interface Switch
Page A
E01
Press
* Zone1
Page B
Press
Zone1
Press Press
Mode
Press **
Press ***
Page C
Page D
* To switch from Page A to Page B, select an appliance first. ** To switch from Page C to Page D, select a target icon first. ***To switch from Page D to Page C, press several times (depending on the page level).
11
3.3 Interface Layout
Page A Home page
Zone1
E01
No
Name
1
Outdoor ambient temperature
Temperature
Zone 2
Current room
2* tempera temperature
ture
Current water temperature
Icon
Note Current outdoor ambient temperature
The indicator lights up when Zone 2 is ON and turns gray when Zone 2 is OFF. When the temperature is controlled by room temperature, is displayed. When the temperature is controlled by water temperature,
is displayed.
12
Set temperature
Radiator
Zone 2 3* applian Underfloor
-ces heating
Fan coil unit
When Zone 2 is selected, the zone indicator and set temperature are visible.
Displays ,
or
depending on the installer
setting.
The icon color is orange
when Zone 2 is in heating
mode.
The icon color is blue when
Zone 2 is in cooling mode.
The icon color is gray when
Zone 2 is OFF.
Temperature
Current room Zone 1 temperature 4 temperatures Current water temperature
Set temperature
The indicator lights up when
Zone 1 is ON and turns gray
when Zone 1 is OFF. When
the temperature is controlled
by room temperature,
is
displayed.
When the temperature is
controlled by water temper-
ature,
is displayed.
When Zone 1 is selected,
the zone indicator and set
temperature are visible.
5 Zone 1 indicator
Zone 1 Indicates this zone is Zone 1.
13
Radiator
Zone 1 Underfloor 6 applian heating
ce
Fan coil unit
Lock
Silent mode 7
WLAN connection
Smart grid
8 Error
DHW Temperature
9**
tank tempe-
Current water
rature temperature
Displays ,
or
depending on the installer
setting. The icon color is orange when Zone 1 is in heating mode. The icon color is blue when Zone 1 is in cooling mode. The icon color is gray when Zone 1 is OFF.
Visible when the screen is locked.
Visible when the silent mode is active.
Visible during WLAN connecting and after successful WLAN connection.
Visible when smart grid function is active.
E01 Visible when any error exists.
The indicator lights up when DHW is ON and turns gray when DHW is OFF. When DHW is selected, set temperature is visible.
14
Set temperature
10** DHW tank
The icon color is orange when DHW heating is ON. The icon color is gray when DHW heating is OFF.
11** Fast DHW
Visible when fast DHW is active.
* Invisible if DOUBLE ZONE is disabled. **Invisible if DHW MODE is disabled.
Page B Appliance page
Zone1
15
No
Name
Date 1
Time
2 Zone indicator
Icon
Zone1
Note
Current date (DD-MM-YYYY) and time (HH:MM) of the wired controller.
Display 1 or 2 depending on the zone you have selected.
Temperature
Current room 3 temperature
Current water temperature
Set temperature
When the temperature is controlled by room temperature,
is displayed. When the temperature is controlled by water temperature,
is displayed.
Radiator
Underfloor 4 Appliance heating
Fan coil unit
Displays ,
or
depending on the installer
setting.
The icon color is orange
when the selected appliance
is in heating mode.
The icon color is blue when
the selected appliance is in
cooling mode.
The icon color is gray when
the selected appliance is OFF.
16
Electric heater Daily timer Silent mode Holiday mode Compressor Water pump Energy saving mode 5 Anti-freeze Defrost Additional heat source Mains electricity
Peak electricity
Green electricity
Solar
Visible if any electric heater is active.
Visible if the daily timer is active.
Visible when silent mode is active.
Visible when holiday mode is active.
Visible when the compressor is running.
Visible when the integrated water pump is running.
Visible when ECO mode is active.
Visible when anti-freeze function is active.
Visible when defrost function is active.
Visible when additional heat source is active.
Visible when smart grid function is active and the input signal is mains electricity.
Visible when smart grid function is active and the input signal is electricity at peak.
Visible when smart grid function is active and the input signal is electricity for free.
Visible when solar heating function is active.
17
Disinfection
Weekly timer
Outdoor ambient temperature Error 6 WLAN connection
Smart grid
Time icon
Time of the Timer
Date of the
7
Timer Timer indicator
Set
operation
mode of the
timer
Set temperature
of the timer
Visible when disinfection function is active. Visible when the weekly timer is active. Current outdoor ambient temperature. Visible when any error exists. Visible during WLAN connecting and after successful WLAN connection Visible when smart grid function is active.
Displays the recent timer information (for Schedule timer only). When no timer is active, “—” is displayed.
18
Page C Menu page
Mode
No. Name Icon
Definition
1 Mode
2 Schedule
3
Weather temp. settings
4 DHW settings
Set the unit operation mode.
The system operates according to a schedule. Allow to regulate the water temperature depending on the outdoor ambient temperature.
Settings of DHW.
5 Settings
General settings.
6 Unit status
More information of the unit and its operation status.
7 Error info
Error history.
8 FAQ
Assistance for common questions.
19
Page D Setting and information page
The page layout varies with your selection. It is either the setting page in which the parameters can be adjusted, or the information page which only provides additional information.
20
4 BASIC OPERATIONS
4.1 Screen Lock/Unlock
The screen dims 30 seconds after no operation, and then turns dark in 10 seconds. To lock or unlock the screen, hold and simultaneously for 1.5 seconds.
4.2 Unit ON/OFF
Select an appliance (icon 3, 6, or 10) in Page A, and press to turn ON/OFF the selected appliance.
Appliance color on the wired controller Appliance status
Dark gray
OFF
Light orange
ON(heating mode)
Light blue
ON(cooling mode)
4.3 Temperature Settings
Select an appliance, and press and to adjust the set temperature.
Set temperature adjustment is feasible regardless of the appliance status.
21
4.4 Mode Change
Mode
Access icon 1 in Page C to change the operation mode. Heating
Press or to change the operation mode. Three modes are optional:, Heating, Cooling, and Auto.
22
NOTE
About AUTO mode: The unit selects the operation mode automatically
based on the outdoor ambient temperature and some advanced settings of the installer. You can see the interfaces as below when the unit is running in different modes. Heating:
Mode
Cooling:
23
Mode
Auto:
Mode
NOTE
Cooling mode for Zone 2 is only available for specific models.
24
5 OTHER FUNCTIONS AND SETTINGS
The settings and operation guide of icons 2, 3, 4, 5, 6, 7, and 8 in Page C are shown below.
NOTE
The icon below is the status indicator. means inactive,and means active.
5.1 Schedule
You can make schedules for the unit operation.
25
The status indicator on the right of the interface shows “ON” when the schedule is active, and “OFF” when the schedule is inactive.
26
NOTE
You might see less items than what is illustrated above. The number of visible items depends on your actual application. This function is based on the current time displayed on the wired controller. Make sure the time is correct. Zone 1 daily timer For daily schedule for Zone 1, 4 parameters can be set. Up to 6 commands can be set..
NOTE
Daily schedule: The commands repeat every day.
27
Time
The time when the unit starts to execute the following command.
Mode
The mode in which the unit starts to run from the set time. OFF means Zone 1 turns off at the set time.
Temp The target temperature of the unit in the set mode.
Status
The status of the schedule setting. If no timer is active, Zone 1 daily timer is inactive.
Zone 2 daily timer Daily schedule for Zone 2. Refer to Zone 1 daily timer. This item is invisible if DOUBLE ZONE is disabled. DHW daily timer Daily schedule for DHW heating. Refer to Zone 1 daily timer. This item is invisible if DHW MODE is disabled.
Zone 1 weekly schedule Weekly schedule for Zone 1. Up to 4 schedules can be set.
28
NOTE
Weekly schedule: The commands repeats every week.
Press and you can see the interface below.
29
Day: Command:
Weekly schedule
Indicates the status of the weekly schedule.
Day
The day on which the following command is active within a week. At least one day should be selected.
Command Refer to Zone 1 daily timer.
30
Zone 2 weekly schedule Weekly schedule for Zone 2. Refer to Zone 1 weekly schedule. This item is invisible if DOUBLE ZONE is disabled. DHW weekly schedule Weekly schedule for DHW heating. Refer to Zone 1 weekly Schedule and DHW daily timer. This item is invisible if DHW MODE is disabled. Holiday away Schedule for holiday, providing a mild temperature for the residence to prevent freezing.
Press and you can see the interface below.
31
Current Status From
Until
Indicates the status of Holiday away mode.
The day on which Holiday away mode starts (00:00 on that day). The day on which Holiday away mode ends (24:00 on that day).
32
Heating Mode* Heating Temp.*
DHW Mode**
Indicates the status of heating mode.
The target temperature of the unit in heating mode.
Indicates the status of DHW heating mode.
DHW
The target temperature of the unit in DHW
Temp.** heating mode.
Disinfect*** Indicates the status of disinfect function.
* Invisible if Heating mode is inactive. ** Invisible if DHW mode is inactive. *** Invisible if DHW mode or disinfection is inactive.
NOTE
You might see less items than what is illustrated above. The number of visible items depends on your actual application.
Quit Holiday away mode in advance:
When Holiday away mode is active, press any button on the wired controller. Then, a confirmation page appears.
For more information, see FAQ.
33
Holiday home In case that user stays at home for holiday, user can make customized schedule.
Press and you can see the interface below.
34
Current Status Indicates the status of Holiday home mode.
From*
The day on which Holiday home mode starts (00:00 on that day)
Until*
The day on which Holiday home mode ends (24:00 on that day)
Zone 1 holiday timer*
Zone 1 holiday timer.
Zone 2 holiday timer*
Zone 2 holiday timer.
DHW holiday timer*
DHW holiday timer.
* Invisible if Holiday home mode is inactive.
35
NOTE
You might see less items than what is illustrated above. The number of visible items depends on your actual application. Quit Holiday home mode in advance: When Holiday home mode is active, press any key on the wired controller. Then, a confirmation page appears.. For more information, see FAQ.
5.2 Weather temp. settings
Weather temp. settings
The set water temperature is regulated automatically depending on the outdoor ambient temperature. This function is only for space heating and space cooling. When the function is active, the unit will apply temperature curves if the current operation mode is consistent with the activated function
36
The status indicator on the right of the interface shows “ON” when the setting is active, and “OFF” when the setting is inactive.
NOTE
If the temperature is controlled by water temperature, you cannot adjust the set temperature (in home page) manually once this function is enabled.
37
If the temperature is controlled by room temperature, the set temperature (in home page) can be adjust as usual.
This function is invalid if the unit is in holiday away or holiday home mode, and the function turns to valid automatically (if this function is set to be active) when the unit quits holiday away or holiday home mode. Zone 1 heating mode Heating temperature curve setting for Zone 1.
Press and you can see the interface below
38
Temperature curve
Indicates the status of temperature curve function.
Select which curve type you want to apply.
Three types in all: Standard, ECO, Custom
Temperature curve type*
Standard: Curves preset by manufacturer, mainly for common conditions
ECO: Curves preset by manufacturer, for energy
saving
Custom: The parameters of the curve can be
adjusted, mainly for advanced users.
Standard
Temperature Up to 8 curves preset by manufacturer, from
level*
which you can choose one.
Temperature offset*
Fine tune the curve. -Slightly increase or decrease the temperature of the curve.
39
ECO**
Temperature Up to 8 curves preset by manufacturer, from
level*
which you can choose one.
ECO timer*
ECO timer: Indicates the status of ECO timer. -If the ECO timer is inactive, the unit will operate in ECO mode all the way. -If the ECO timer is active, the unit will operate in ECO mode only during the set time period. Start: the hour from which the ECO curve is enabled; End: the hour from which the ECO curve is disabled -If the set Start time is later than the set End time, the unit will operate in ECO mode throughout a day. The Start time and End time cannot be set to the same value. Otherwise, the most recent setting is invalid, and a notice window appears.
Custom
Temperature setting*
The parameters of the curve can be adjusted.
Temperature offset*
Fine tune the curve. -Slightly increase or decrease the temperature of the curve.
* Invisible if Temperature curve function is inactive.
40
** Available only for Zone 1 heating mode and single zone application. Zone 1 cooling mode Cooling temperature curve setting for Zone 1. Refer to Zone 1 heating mode. Zone 2 heating mode Heating temperature curve setting for Zone 2. Refer to Zone 1 heating mode.
NOTE
Invisible if DOUBLE ZONE is disabled.
Zone 2 cooling mode Cooling temperature curve setting for Zone 2. Refer to Zone 2 heating mode.
NOTE
Invisible if DOUBLE ZONE is disabled.
Introduction to weather temp. settings It provides some basic knowledge about the temperature curve. For more information, see FAQ.
41
5.3 DHW settings
DHW settings
NOTE
Invisible if DHW MODE is disabled. The status indicator on the right of the interface shows “ON” when the setting is active, and “OFF” when the setting is inactive.
42
Disinfect
Kill Legionella at high temperature.
Current State Indicates the status of Disinfect function.
The day on which Disinfect function is Operate Day active within a week. At least one day
should be selected.
Start
The hour when Disinfect function starts.
Fast DHW*
Indicates the status of Fast DHW function. -Fast DHW function forces the unit to run in DHW mode (the unit will switch to DHW mode immediately). -Fast DHW serves to activate auxiliary heat sources such as TBH, AHS, and IBH for DHW heating.
Tank heater*
Indicates the status of Tank heater function. -Tank heater function serves to activate TBH.
DHW pump
Daily schedule for DHW pumps -Up to 12 commands can be set. The operation time of DHW pumps for each command is 5 minutes.
* The status indicator will turn OFF automatically after the function ends.
43
Disinfect
Press and you can see the interface below
Operation
NOTE
If there is DHW Timer set off during disinfect function running. The disinfect function will be stopped without any notice.
44
DHW pump
5.4 Settings
Settings
The status indicator on the right of the interface shows “ON” when the setting is active, and “OFF” when the setting is inactive.
45
Silent and boost mode setting
Silent and boost mode setting You can select Silent mode or Boost mode. In Silent mode, the unit operates without producing much noise. In Boost mode, the unit operates with higher capacity and higher noise, power consumption as well.
46
Silent and boost mode setting Current state
Press and you can see the interface below.
Silent and boost mode setting Current state Mode setting
NOTE
Boost mode is only available for specific models. 47
Silent and boost mode setting
Current state Mode setting Timer 1 From Until
Timer 2 From Until
Indicate the status of Silent and boost mode setting.
Select which level you want to apply to: (1)Silent; (2)Super silent; (3)Boost Indicate the status of Timer 1. The Silent and boost mode setting start time of Timer 1 The Silent and boost mode setting end time of Timer 1 Indicate the status of Timer 2. The Silent and boost mode setting start time of Timer 2 The Silent and boost mode setting end time of Timer 2
When Current state is active and Timer is inactive, the unit runs in Silent or Boost mode all the time. When Current state is active and Timer is also active, the unit runs in Silent or Boost mode only in the set time period.
48
If the set start time is later than the set end time, the unit will operate in Silent or Boost mode throughout a day. The Start time and End time cannot be set to the same value. Otherwise, the most recent setting is invalid, and a notice window appears. Backup Heater
Invisible when IBH/AHS function is disabled. The status indicator will turn OFF automatically after the function if off.
Silent and boost mode setting
Display Setting
49
Time Date
Set the current time of HMI. Set the current date of HMI.
Set summer time start time and end time.
Daylight saving time
NOTE
Timer could be skipped when the wired controller switches summer time.
Language Backlight Buzzer
Screen Lock Screen Lock Time Decimal separator
Set the language of HMI.
Set the backlight brightness. Indicates the status of Buzzer. Reminds user how to lock and unlock the screen. Set the automatic screen lock timer.
Switch decimal separator type.
50
WLAN Setting
Smart Link
Jump to a new page, which contains the SN code of the wired controller. -Every time you enter the Smart Link screen, the WLAN connection is activated for 5 minutes. -With the WLAN connection activated, connect to the unit through the app. Refer to the instructions of the app for more information.
A page for confirmation appears.
-If you confirm the reset, the unit will
Reset WLAN disconnect with the app. If you want to use the
setting
app to operate the unit, connect the unit with
the WLAN again.
Force Defrost
Current State: Indicates the status of Force Defrost. The status indicator will turn OFF automatically after Force
Defrost ends.
51
5.5 Unit Status
Unit status
Device info.
A list of parameters related to the units (both
master units and slave units).
Operation parameter
You can check the current status parameter.
Press or to switch the unit.
of
each
-Ask your installer for more information of each
parameter.
52
You can check the produced energy, consumed
power and efficiency of the unit for every type.
Three types in all:
-Heating energy data*
-Cooling energy data*
-DHW energy data*
Energy
Two functions: -Energy data: you can check the hourly, daily,
metering weekly, monthly, or yearly data or total data.
-Historical data: you can check the historical data.
NOTE
COP/EER is calculated under normal operating conditions.
Device info.
The SN code and software version of the wired controller, outdoor unit or indoor unit (if applicable). Press to switch information page (SN code and software) You can check both the master units and slave units. Press or to switch the unit (master units and slave units).
Service call
The phone number of your installer or dealer.
* Visible with — displayed, if the function is disabled accordingly.
53
Operation parameter Energy metering
54
Energy data: 55
Historical data:
5.6 Error Info
Error info
Access icon 7 in page C. Then, unit errors (if any) are displayed.
56
You can press at each record to check the definition of the error code.
Clear Error info. Press and hold Error info.
for 5 seconds to clear all the records in
57
5.7 FAQ
FAQ
Access icon 8 in page C. Then, a QR code is displayed.
Scan the QR code for more details about the wired controller. 58
6 INSTALLATION CONFIGURATION
To be filled in by the installer.
Code Date
Setting DHW setting
DHW mode Disinfect DHW priority Pump_D DHW priority time set dT5_ON dT1S5 T4DHWMAX T4DHWMIN T5S_Disinfect t_DI_HIGHTEMP. t_DI_MAX t_DHWHP_Restrict t_DHWHP_MAX Pump_D timer Pump_D running time Pump_D disinfect
Unit
/ / / / / °C/ F °C/ F °C/ F °C/ F °C/ F Minutes Minutes Minutes Minutes / Minutes /
59
Cooling mode t_T4_Fresh_C T4CMAX T4CMIN dT1SC dTSC Zone 1 C-emission Zone 2 C-emission T1SCLMIN
Heating mode t_T4_Fresh_H T4HMAX T4HMIN dT1SH dTSH Zone 1 H-emission Zone 2 H-emission Force defrost
T4AUTOCMIN T4AUTOHMAX
Cooling setting Heating setting
AUTO mode setting 60
/ Hour °C/ F °C/ F °C/ F °C/ F
/ / °C/ F
/ Hours °C/ F °C/ F °C/ F °C/ F
/ / /
°C/ F °C/ F
Temp. type setting
Water flow temp.
Room temp.
Double zone
Room thermostat setting
Room thermostat
Other heat source
IBH function dT1_IBH_ON t_IBH_Delay T4_IBH_ON P_IBH1 P_IBH2 AHS function AHS_Pump_I Control dT1_AHS_ON t_AHS_Delay T4_AHS_ON EnSwitchPDC GAS-COST ELE-COST MAX-SETHEATER
/ / /
/
/ °C/ F Minutes °C/ F
kW kW
/ / °C/ F Minutes °C/ F / Price/m3 Price/kWh °C/ F
61
MIN-SETHEATER MAX-SIGHEATER MIN-SIGHEATER TBH function dT5_TBH_ OFF t_TBH_Delay T4_TBH_ON P_TBH Solar function Solar control Deltatsol
Preheating for floor T1S t_ARSTH Floor drying up t_Dryup t_Highpeak t_Drydown t_Drypeak
Special function
62
°C/ F V V /
°C/ F Minutes
°C/ F kW
/ / °C/ F
/ °C/ F Hours
/ Days Days Days °C/ F
Start time Start date
Auto restart cooling/heating mode
Auto restart
Auto restart DHW mode
Power input limitation
Power input limitation
M1 M2 SMART GRID T1T2 TBT P_X port
PER_START TIME_ADJUST
Address reset
HMI address for BMS
Input definition Cascade setting HMI address setting
63
h/min dd/mm/yy
/
/
/
/ / / / /
% Minutes
/
/
Stop BIT
t_Delay pump t1_Antilock pump t2_Antilock pump run t1_Antilock SV t2_Antilock SV run Ta-adj. F-PIPE LENGTH Pump_I silent output Energy metering
Common setting
/
Minutes Hours Seconds Hours Seconds °C/ F
/ % /
64
7 OPERATING PARAMETERS
No.
Code Date
Value
1 ODU model
2 Operation mode
3 Comp. frequency
4 Fan 1 speed
5 Fan 2 speed(if available)
6 Expansion valve 1
7
Expansion valve 2(if available)
8
Expansion valve 3(if available)
9
Tp comp. discharge temp.
10 Th comp. suction temp.
11
T3 outdoor exchanger temp.
12 TL distributor temp.
13 T4 outdoor air temp.
14 TF module temp.
15 T9i temp(if available)
16 T9o temp(if available)
17 P1 comp. pressure
18 P2 comp. pressure
19 T2b plate F-in temp.
20 T2 plate F-out temp.
65
21
Tw_in plate water inlet temp.
22
Tw_out plate water outlet temp.
23 T1 leaving water temp.
24 Tw2 circuit2 water temp.
25 Ta room temp.
26 T5 water tank temp.
27 Tbt buffer tank temp.
28 T1S_C1 CLI. curve temp.
29
T1S2_C2 CLI. curve temp.
30 Water pressure
31 Water flow
32 ODU current
33 ODU voltage
34 DC voltage
35 DC current
36 Pump_I PWM
66
www.kaisai.com
Owner’s manual Instrukcja obslugi Bedienungsanleitung
68
Documents / Resources
 | Wired Controller |
References
- Home | Kaisaiwww.kaisai.com
- User Manualmanual.tools