FMC920
Small and smart tracker
Quick Manual v3.0
CONTENT
Know your device................................................................................................................................................................................................3 Pinout ...................................................................................................................................................................................................................4 Wiring scheme.....................................................................................................................................................................................................5 Set up your device ..............................................................................................................................................................................................6 PC Connection (Windows)..................................................................................................................................................................................7 How to install USB drivers (Windows) ..............................................................................................................................................................7 Configuration.......................................................................................................................................................................................................8 Quick SMS configuration................................................................................................................................................................................. 10 Mounting recommendations.......................................................................................................................................................................... 12 Basic characteristics ........................................................................................................................................................................................ 13 LED indications................................................................................................................................................................................................. 13 Electrical characteristics.................................................................................................................................................................................. 16 Safety information .......................................................................................................................................................................................... 17 Certification and Approvals ............................................................................................................................................................................ 18 Warranty ........................................................................................................................................................................................................... 20 Warranty disclaimer......................................................................................................................................................................................... 20
Quick Manual v3.0 // FMC920 2
KNOW YOUR DEVICE
TOP VIEW (WITHOUT COVER)
POWER CABLE
BOTTOM VIEW (WITHOUT COVER)
MICRO-USB
NAVIGATE LED
STATUS LED
BATTERY SOCKET
MICRO-SIM SLOT
Quick Manual v3.0 // FMC920 3
PINOUT
PIN NUMBER PIN NAME
DESCRIPTION
1
VCC (10-30) V DC (+)
(Red) Power supply (+10-30 V DC)
+10...30 V DC
1
2
GND (-)
(Black) Ground
GND
2
(Yellow) Digital input,
3
DIN1
channel 1. DEDICATED FOR IGNITION INPUT
DIN1
3
4
AIN1
(Grey) Analog input, channel 1. Input range:
AIN1
4
0-30 V DC
(White) Digital output.
DOUT1
5
5
DOUT1
Open collector output.
Max. 0,5 A DC
FMC920 pinout
Quick Manual v3.0 // FMC920 4
WIRING SCHEME
IGNITION DETECTION
87 87a 86 85 30
ALARM BUTTON
DOOR SENSOR
+10...30 V DC
1
GND
2
DIN1
3
AIN1
4
DOUT1
5
FUEL GAUGE
BUZZER
STARTER
ANALOG LLS SENSOR
POWER SUPPLY 10 - 30V DC
Quick Manual v3.0 // FMC920 5
SET UP YOUR DEVICE
HOW TO INSERT MICRO-SIM CARD
1 COVER REMOVAL
Gently remove FMC920 cover using plastic pry tool from both sides.
2 MICRO-SIM CARD INSERT
Insert Micro-SIM card as shown with PIN request disabled or read Security info1 how to enter it later in Configurator. Make sure that Micro-SIM card cut-off corner is pointing forward to slot.
3 REMOVING PROTECTION
Remove the adhesive tape protection.
1wiki.teltonika-gps.com/view/FMC920_Security_info
4 PLACING BATTERY
Place the battery inside the casing of the FMC920. Make sure the adhesive tape sticks to the casing.
5 CONNECTING BATTERY
Connect the internal battery to the FMC920 PCB.
6 ATTACHING COVER BACK
Attach device cover back. Device is ready to be connected.
Quick Manual v3.0 // FMC920 6
PC CONNECTION (WINDOWS)
1. Power-up FMC920 with DC voltage (10 30 V) power supply using power wires. LED's should start blinking, see "LED indications1".
2. Connect device to computer using Micro-USB cable or Bluetooth® connection: · Using Micro-USB cable · You will need to install USB drivers, see "How to install USB drivers (Windows)2" · Using Bluetooth® wireless technology · FMC920 Bluetooth® technology is enabled by default. Turn on Bluetooth® connection on your PC, then select Add Bluetooth or other device > Bluetooth. Choose your device named "FMC920_last_7_imei_digits", without LE in the end. · Enter default password 5555, press Connect and then select Done.
3. You are now ready to use the device on your computer.
1Page 13, "LED indications" 2Page 7, "How to install USB drivers (Windows)"
HOW TO INSTALL USB DRIVERS (WINDOWS)
1. Please download COM port drivers from here1. 2. Extract and run TeltonikaCOMDriver.exe. 3. Click Next in driver installation window. 4. In the following window click Install button. 5. Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the
setup.
1wiki.teltonika-gps.com/images/d/d0/TeltonikaCOMDriver.zip
Quick Manual v3.0 // FMC920 7
CONFIGURATION
At first FMC920 device will have default factory settings set. These settings should be changed according to the users needs. Main configuration can be performed via Teltonika Configurator1 software. Get the latest Configurator version from here2. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.
1wiki.teltonika-gps.com/view/Teltonika_Configurator 2wiki.teltonika-gps.com/view/Teltonika_Configurator_versions
MS .NET REQUIREMENTS
Operating system
Windows Vista Windows 7 Windows 8.1 Windows 10
MS .NET Framework version Version
MS .NET 5.0
32 and 64 bit
1dotnet.microsoft.com/en-us/download/dotnet/5.0/runtime
Links www.microsoft.com1
Quick Manual v3.0 // FMC920 8
Various Status window1 tabs display information about GNSS2, GSM3, I/O4, Maintenance5 and etc. FMC920 has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality:
Downloaded Configurator will be in compressed archive.
Extract it and launch Configurator.exe. After launch software
language can be changed by clicking in the right bottom corner.
FMC920
Configuration process begins by pressing on connected device.
Load from device loads configuration from device. Save to device saves configuration to device. Load from file loads configuration from file. Save to file saves configuration to file. Update firmware updates firmware on device. Read records reads records from the device.
FMC920
After connection to Configurator Status window will be displayed.
Reboot device restarts device.
Reset configuration sets device configuration to default.
Most important configurator section is GPRS where all your server and GPRS settings6 can be configured and Data Acquisition7 where data acquiring parameters can be configured. More details about FMC920 configuration using Configurator can be found in our Wiki8. 1wiki.teltonika-gps.com/view/FMC920_Status_info 2wiki.teltonika-gps.com/view/FMC920_Status_info#GNSS_Info 3wiki.teltonika-gps.com/view/FMC920_Status_info#GSM_Info 4wiki.teltonika-gps.com/view/FMC920_Status_info#I.2FO_Info 5wiki.teltonika-gps.com/view/FMC920_Status_info#Maintenance 6wiki.teltonika-gps.com/view/FMC920_GPRS_settings 7wiki.teltonika-gps.com/view/FMC920_Data_acquisition_settings 8wiki.teltonika-gps.com/view/FMC920_Configuration
Quick Manual v3.0 // FMC920 9
QUICK SMS CONFIGURATION
Default configuration has optimal parameters present to ensure best performance of track quality and data usage. Quickly set up your device by sending this SMS command to it:
« setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0»
1
2
3
4
5
6
Note: Before SMS text, two space symbols should be inserted.
GPRS SETTINGS: 1 2001 APN
2 2002 APN username (if there are no APN username, empty field should be left)
3
2003 APN password (if there are no APN password, empty field should be left)
SERVER SETTINGS: 4 2004 Domain 5 2005 Port 6 2006 Data sending protocol (0 TCP, 1 UDP)
Quick Manual v3.0 // FMC920 10
DEFAULT CONFIGURATION SETTINGS
MOVEMENT AND IGNITION DETECTION: VEHICLE MOVEMENT will be detected by accelerometer
DEVICE MAKES A RECORD ON MOVING IF ONE OF THESE EVENTS HAPPEN:
300 seconds passes
VEHICLE TURNS 10 degrees
IGNITION WILL BE DETECTED by vehicle power voltage between 13,2 30 V
VEHICLE DRIVES 100 meters
SPEED DIFFERENCE between last coordinate and current position is greater than 10 km/h
DEVICE MAKES A RECORD ON STOP IF:
RECORDS SENDING TO SERVER:
1 HOUR PASSES while vehicle is stationary and ignition is off
IF DEVICE HAS MADE A RECORD it is sent to the server every 120 seconds
After successful SMS configuration, FMC920 device will synchronize time and update records to configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator1 or SMS parameters2.
1wiki.teltonika-gps.com/view/Teltonika_Configurator 2wiki.teltonika-gps.com/view/Template:FMB_Device_Family_Parameter_list
Quick Manual v3.0 // FMC920 11
MOUNTING RECOMMENDATIONS
CONNECTING WIRES
· Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and moving objects near the wires.
· The connections should not be seen very clearly. If factory isolation was removed while connecting wires, it should be applied again.
· If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.
· Wires cannot be connected to the board computers or control units.
CONNECTING POWER SOURCE
· Be sure that after the car computer falls asleep, power is still available on chosen wire. Depending on car, this may happen in 5 to 30 minutes period.
· When module is connected, measure voltage again to make sure it did not decrease. · It is recommended to connect to the main power cable in the fuse box. · Use 3A, 125V external fuse.
CONNECTING IGNITION WIRE
· Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine. · Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available). · Check if power is still available when you turn off any of vehicles devices. · Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on,
may be chosen.
CONNECTING GROUND WIRE
· Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame. · If the wire is fixed with the bolt, the loop must be connected to the end of the wire. · For better contact scrub paint from the spot where loop is going to be connected.
Quick Manual v3.0 // FMC920 12
LED INDICATIONS
BASIC CHARACTERISTICS
NAVIGATION LED INDICATIONS
BEHAVIOUR Permanently switched on Blinking every second
Off
Blinking fast constantly
MEANING
GNSS signal is not received
Normal mode, GNSS is working
GNSS is turned off because: Device is not working or Device is in sleep mode
Device firmware is being flashed
STATUS LED INDICATIONS
BEHAVIOUR
Blinking every second
Blinking every two seconds
Blinking fast for a short time
Off
MEANING Normal mode
Sleep mode
Modem activity Device is not working or Device is in boot mode
MODULE Name Technology
FMC920-QJIB0: Quectel EG915U-EU with Teltonika TM2500 FMC920-QKIB0: Quectel EG915U-LA with Teltonika TM2500
LTE Cat 1/GSM/GPRS/GNSS/ BLUETOOTH® LE
GNSS
GNSS
Receiver Tracking sensitivity Accuracy Hot start Warm start Cold start
GPS, GLONASS, GALILEO, BEIDOU, QZSS, AGPS 33 channel -165 dBM < 3 m < 1 s < 25 s < 35 s
CELLULAR Technology 2G bands
LTE Cat 1, GSM
FMC920-QJIB0: GSM: B2/B3/B5/B8 FMC920-QKIB0: GSM: B2/B3/B5/B8
Quick Manual v3.0 // FMC920 13
4G bands Data transfer Transmit power Data support
FMC920-QJIB0: LTE FDD: B1/B3/B5/ B7/B8/B20/B28 FMC920-QKIB0: LTE FDD: B2/B3/B4/ B5/B7/B8/B28/ B66
LTE: LTE FDD : Max 10Mbps (DL)/ Max 5Mbps (UL) GSM: GPRS: Max 85.6Kbps (DL)/ Max 85.6Kbps (UL)
Class 5 for GSM900: 30±5dBm Class 3 for DCS1800: 29±5dBm Class 3 for LTE-FDD: 26±5dBm Bluetooth: 5.54dBm +/-2dBm Bluetooth LE: -4.26dBm +/-2dBm
SMS (text/data)
POWER Input voltage range Back-up battery Internal fuse
10 - 30 V DC with overvoltage protection
170 mAh Li-Ion battery (0.63Wh)
3A, 125V
Power consumption
At 12V < 2 mA (Ultra Deep Sleep1)
At 12V < 3 mA (Deep Sleep1)
At 12V < 8 mA (Online Deep Sleep1)
At 12V < 12 mA (GNSS Sleep1) At 12V < 28 mA (Nominal with no laod)
At 12V < 0.25A Max. (with full Load/ Peak)
1wiki.teltonika-gps.com/view/FMC920_Sleep_modes
BLUETOOTH® TECHNOLOGY
Specification
4.0 + LE
Supported peripherals
EYE beacon and sensor2, OBDII dongle3, Inateck Barcode Scanner,Universal Bluetooth® LE sensors support
INTERFACE Digital Inputs Digital Outputs Analog Inputs
GNSS antenna Cellular antenna USB LED indication SIM Memory
1 1 1
Internal High Gain Internal High Gain 2.0 Micro-USB 2 status LED lights Micro-SIM 128MB internal flash memory
PHYSICAL SPECIFICATION
Dimensions
79 x 43 x 12 mm (L x W x H)
Weight
54 g
2teltonika-gps.com/products/accessories/sensors-beacons 3wiki.teltonika-gps.com/view/How_to_connect_OBD_II_Bluetooth_ Dongle_to_FMB_device
Quick Manual v3.0 // FMC920 14
OPERATING ENVIRONMENT
Operating temperature (with battery)
-20 °C to +40 °C
Operating temperature (without battery)
-40 °C to +85 °C
Storage temperature (without battery)
-40 °C to +85 °C
Storage temperature (with battery)
-20 °C to +60 °C
Operating humidity 5% to 95% non-condensing
Ingress Protection Rating
IP54
Battery charge temperature
0 °C to +45 °C
Battery discharge temperature
Battery storage temperature
-20 °C to +60 °C
-20 °C to +45 °C for 1 month -20 °C to +35 °C for 6 months
FEATURES Sensors
Accelerometer
Scenarios
Sleep modes Configuration and firmware update SMS
Green Driving, Over Speeding detection, GNSS Fuel Counter, DOUT Control Via Call, Excessive Idling detection, Unplug detection, Towing detection, Crash detection, Auto Geofence, Manual Geofence, Trip4
GPS Sleep, Online Deep Sleep, Deep Sleesp, Ultra Deep Sleep5
FOTA Web6, FOTA7, Teltonika Configurator8 (USB, Bluetooth® wireless technology)
Configuration, Events, DOUT Control, Debug
GPRS commands Time Synchronization Fuel monitoring
Ignition detection
Configuration, DOUT control, Debug
GPS, NITZ, NTP
LLS (Analog), OBDII dongle9 Digital Input 1, Accelerometer, External Power Voltage, Engine RPM (OBDII dongle10)
4wiki.teltonika-gps.com/view/FMC920_Features_settings 5wiki.teltonika-gps.com/view/FMC920_Sleep_modes 6wiki.teltonika-gps.com/view/FOTA_WEB 7wiki.teltonika-gps.com/view/FOTA 8wiki.teltonika-gps.com/view/Teltonika_Configurator 9wiki.teltonika-gps.com/view/How_to_connect_OBD_II_Bluetooth_ Dongle_to_FMB_device
Quick Manual v3.0 // FMC920 15
ELECTRICAL CHARACTERISTICS
CHARACTERISTIC DESCRIPTION
MIN.
SUPPLY VOLTAGE
Supply Voltage
(Recommended
+10
Operating Conditions)
VALUE
TYP.
MAX. UNIT
+30 V
DIGITAL OUTPUT (OPEN DRAIN GRADE)
Drain current (Digital Output OFF)
Drain current (Digital Output ON, Recommended Operating Conditions)
Static Drain-Source resistance (Digital Output ON)
120 µA
0.5
A
300 m
DIGITAL INPUT
Input resistance (DIN1) 47
k
Input voltage
(Recommended
0
Operating Conditions)
30
V
Input Voltage threshold
2.5
V
CHARACTERISTIC DESCRIPTION
MIN.
ANALOG INPUT
Input Voltage
(Recommended
0
Operating Conditions)
Input resistance
Measurement error on 12V
Additional error on 12V
Measurement error on 30V
Additional error on 30V
VALUE
TYP.
MAX. UNIT
30
V
150
k
3
%
360
mV
3
%
900
mV
Quick Manual v3.0 // FMC920 16
SAFETY INFORMATION
This message contains information on how to operate FMC920 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!
· The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10...+30 V DC.
· To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.
· When connecting the connection (1x5) cables to the vehicle, the appropriate jumpers of the power supply of the vehicle should be disconnected.
· Before dismounting the device from the vehicle, the 1x5 connection must be disconnected.
· The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 62368-1 standard.
· The device FMC920 is not designed as a navigational device for boats.
Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the powe supply.
All wireless data transferring devices produce interference that may affect other devices which are placed nearby.
The device must be connected only by qualified personnel.
The device must be firmly fastened in a predefined location.
The programming must be performed using a PC with autonomic power supply.
Installation and/or handling during a lightning storm is prohibited.
The device is susceptible to water and humidity.
Quick Manual v3.0 // FMC920 17
CERTIFICATION AND APPROVALS
This sign on the package means that it is necessary to read the User`s Manual before your start using the device. Full User`s Manual version can be found in our Wiki1.
1wiki.teltonika-gps.com/view/FMC920
Hereby, Teltonika declare under our sole responsibility that the above described product is in conformity with the relevant Community harmonization: European Directive 2014/53/EU (RED).
UK Conformity Assessed (UKCA) marking is a conformity mark that indicates conformity with the applicable requirements for above described products sold within Great Britain.
The RoHS1 is a directive regulating the manufacture, import and distribution of Electronics and Electrical Equipment (EEE) within the EU, which bans from use 10 different hazardous materials (to date).
1wiki.teltonika-gps.com/view/FMC920_RoHS
This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste.
E57
E-Mark and e-Mark are the European conformity marks issued by the transport sector, indicating that the products comply with relevant laws and regulations or directives. Vehicles and related products need to go through the E-Mark certification process to be legally sold in Europe.
REACH
REACH addresses the production and use of chemical substances, and their potential impacts on both human health and the environment. Its 849 pages took seven years to pass, and it has been described as the most complex legislation in the Union's history and the most important in 20 years. It is the strictest law to date regulating chemical substances and will affect industries throughout the world.
IP
RATING
The standard aims to provide users more detailed information than vague marketing terms such as waterproof.
Quick Manual v3.0 // FMC920 18
DECLARATION OF IMEI ASSIGNMENT
The IMEI number is used by a GSM network to identify valid devices and therefore can be used for stopping a stolen phone from accessing that network. For example, if a mobile phone is stolen, the owner can call their network provider and instruct them to blacklist the phone using its IMEI number. This renders the phone useless on that network and sometimes other networks too, whether or not the phone's subscriber identity module (SIM) is changed.
DECLARATION OF DEVICE OPERATION TEMPERATURE
An operating temperature is the temperature at which an electrical or mechanical device operates. The device will operate effectively within a specified temperature range which varies based on the device function and application context, and ranges from the minimum operating temperature to the maximum operating temperature (or peak operating temperature). Outside this range of safe operating temperatures the device may fail.
Para maiores informações, consulte o site da ANATEL www.anatel.gov.br Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados.
For more information, see the ANATEL website www.anatel.gov.br This equipment is not entitled to protection against harmful interference and must not cause interference in duly authorized systems.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by UAB Teltonika Telematics is under license. Other trademarks and trade names are those of their respective owners.
CHECK ALL CERTIFICATES
All newest certificates may be found in our Wiki2. 2 wiki.teltonika-gps.com/view/FMC920_Certification_%26_Approvals
Quick Manual v3.0 // FMC920 19
WARRANTY
We guarantee our products 24-month warranty1 period. All batteries carry a 6-month warranty period. Post-warranty repair service for products is not provided. If a product stops operating within this specific warranty time, the product can be: · Repaired · Replaced with a new product · Replaced with an equivalent repaired product fulfilling the same functionality · Replaced with a different product fulfilling the same functionality in case of EOL for the original product
1Additional agreement for an extended warranty period can be agreed upon separately.
WARRANTY DISCLAIMER
· Customers are only allowed to return products as a result of the product being defective, due to order assembly or manufacturing fault.
· Products are intended to be used by personnel with training and experience. · Warranty does not cover defects or malfunctions caused by accidents, misuse, abuse, catastrophes, improper maintenance
or inadequate installation not following operating instructions (including failure to heed warnings) or use with equipment with which it is not intended to be used. · Warranty does not apply to any consequential damages. · Warranty is not applicable for supplementary product equipment (i. e. PSU, power cables, antennas) unless the accessory is defective on arrival. · More information on what is RMA1
1wiki.teltonika-gps.com/view/RMA_guidelines
Quick Manual v3.0 // FMC920 20
1wiki.teltonika-gps.com/images/d/d0/TeltonikaCOMDriver.zip
Download .NET 5.0 Runtime
Bluetooth® Sensors & Beacons To Expand The Usage Of GPS Trackers
FMC920 Data acquisition settings - Teltonika Telematics Wiki
Direitos do Consumidor — Agência Nacional de Telecomunicações