BHALGSA L-Shape Height Adjustable Workstation
Specifications
- Product: THINK L-Shape Height-Adjustable Workstation
- Model: BHALGSA
Product Usage Instructions
Assemble Leg Post Separately
Attach center leg with motor to the center post brackets using screws (A). Then, attach side legs with motor and arm brackets to left and right adjustable beams.
Note: Replace the default arm brackets if workstation requires BHA19 or T-brackets.
Attach Workstation Frame
Join all three legs by attaching the inner adjustable beams to the left and right adjustable beams and center post brackets. Keep locking screws (B) loose on the inner adjustable beams to accommodate surface size in step 3.
Place Frame on Surface
Secure flat plate, flat bracket(s), and support bars to the surfaces using screws (F). Extend beam to fit table size accordingly. Secure locking screws on the adjustable beam and attach to surface using screws (F).
Note: If using surface-mounted dividers, keep the frame] 1.5 inches inset from the surface edge. If not using surface-mounted dividers, bring frame flushed to edge of surface. Use additional flat brackets as needed.
Install Feet, Gliders, and Control Box
Install feet using screws (D) for outside legs. Install center] post base to center leg using screws (E). Mount control box to the adjustable beam using screw (G). Then, secure power cord to the control box. Mount handset using wood screws (C) and attach to control box. If workstation is complete, flip over. Reference handset guide for initialization and operation functions.
FAQ
Q: Are additional parts required for multiple workstations?
A: Yes, additional parts will be needed for each additional workstation.
Workstation Overview
THINK L-Shape Height-Adjustable Workstation
All parts listed are for a single workstation; additional parts will be needed for additional workstations.
Parts List
Assemble Leg Post Separately
Attach center leg with motor to the center post brackets using screws (A). Then, attach side legs with motor and arm brackets to left and right adjustable beams.
Note: Replace the default arm brackets if workstation requires BHA19 or T-brackets.
Attach Workstation Frame
Join all three legs by attaching the inner adjustable beams to the left and right adjustable beams and center post brackets. Keep locking screws (B) loose on the inner adjustable beams to accommodate surface size in step 3. Place Frame on Surface
Secure flat plate, flat bracket(s), and support bars to the surfaces using screws (F).
Extend beam to fit table size accordingly. Secure locking screws on the adjustable beam and attach to surface using screws (F).
Note: If using surface-mounted dividers, keep the frame 1.5 inches inset from the surface edge. If not using surface-mounted dividers, bring frame flushed to edge of surface. Use additional flat brackets as needed.
Install Feet, Gliders, and Control Box
Install feet using screws (D) for outside legs. Install center post base to center leg using screws (E). Mount control box to the adjustable beam using screw (G). Then, secure power cord to the control box. Mount handset using wood screws (C) and attach to control box. If workstation is complete, flip over. Reference handset guide for initialization and operation functions.
A2: Modesty Panel Overview
THINK L-Shape Height-Adjustable Workstation
All parts listed are for a single modesty panel; additional parts will be needed for additional modesty panels.
Parts List
*NOTE: For Steel Modesty Panel: components may vary, but process is similar.
- Secure Brackets to Modesty Panel
Connect the BMPBFB bracket to the modesty panel using screws. Secure tightly.
NOTE: If modesty panel does not have pre-drilled holes, use wood screws instead of machine screws. - Attach Modesty Panel to Surface
Attach modesty panel to surface using wood screws provided with brackets. Panel will be center aligned and flushed with back of surface.
A3: Slim Pedestal Overview
THINK L-Shape Height-Adjustable Workstation
All parts listed are for a single slim pedestal; addi-tional parts will be needed for additional slim pedestals.
Parts List
- Secure Brackets to Slim Pedestal
Align large mounting bracket to front of pedestal and align small mounting bracket to back. Secure both brackets using provided screws. - Attach Slim Pedestal to Surface
Secure pedestal to surface using wood screws. Pedestal brackets will connect on either side of the center beam.
A4: Cable Tray Overview
THINK L-Shape Height-Adjustable Workstation
All parts listed are for a single cable tray; additional parts will be needed for additional cable trays.
Parts List
Extend Cable Tray to Desired Length
Extension range: 25” –45”.Attach Cable Tray to Surface
Attach cable tray using wood screws.
1-866-999-0955 | hello@juniperoffice.com | juniperoffice.com © 2023 Juniper Office | Version 23.0.0
Documents / Resources
![]() | Juniper BHALGSA L-Shape Height Adjustable Workstation [pdf] Installation Guide BHALGSA, BHALGSA L-Shape Height Adjustable Workstation, L-Shape Height Adjustable Workstation, Height Adjustable Workstation, Adjustable Workstation, Workstation |