JOHN LEWIS 238928457 Stella Ceiling Light

Introduction

Thank you for purchasing this STELLA CEILING LIGHT Please read the instructions carefully before use to ensure safe and satisfactory operation of this product.

Warnings 

The fitting is class II.
This fitting should be fitted in accordance with IEE Regulations and the Building Regulations. If in any doubt, or where required by law, consult a competent person who is registered with an electrical self-certification scheme. Further information is available online or from your Local Authority. To prevent electric shock switch off at the mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electricity supply without your knowledge. If you are in any doubt, please consult a qualified electrician. If replacing an existing fitting, make a note of the connections. Always use the correct type and wattage bulb. Never exceed the wattage stated.When changing a bulb, always switch off at the mains and allow the old bulb to cool down before handling. Dispose of used bulbs carefully. The flexible cable of this product is not replaceable. If damaged, the product shall be disposed of. It is the installer’s responsibility to ensure that the fixings and wall plugs used are suitable for the surface you are fixing your product on.

CAUTION! The bulb and surrounding parts can become hot during use.

Parts

No. Picture Name Qty
WALL PLUGS X2
SCREW X2
107 U SHAPE BRACKET X1
TERMINAL BLOCK X1
DIAMETER 30XH119.5 CRYSTAL CHAIN X4
DIAMETER 30XH145.5 CRYSTAL CHAIN X8
DIAMETER 30*H172 CRYSTAL CHAIN X16
DIAMETER 400 GLASS SHADE X1
DIAMETER 40XH145CM LAMP BODY X1

Product assembly

Ensure the house electricity supply is switched off at the fuse board.

Step 1 Fix bracket(C) ceiling by using screws (A)(B)provided. Ensure that the bracket is fixed to a wooden joist, or use a suitable fixing to the ceiling which will support the weight of the fitting.

Step 2 Place glass shade(H)onto metal plate (I).

Step 3 Connect cables or terminals as shown below

Check all wires are tight in the terminal block(D),and no loose strands are left out. Cover with insulating tape (not included).

Step 4 Remove the protective film. Attach the crystal chain (E) (F) (G) onto the metal plate working from inner outwards. above. Fit the light bulb(not included) into socket. The maximum power indicated must not be exceeded. Switch on the electricity supply at the fuse board.

Caring for your product

Indoor use only.
Non-Dimmable.
Replace bulbs from John Lewis or established brand of the same type and compatibility. Recommend the fitting should be cleaned with a soft dry cloth.

Aftercare and Troubleshooting

Why is the light not working when switched on?

Check your power supply is switched on Turn off light and check that the bulb is inserted correctly Check the bulb is still in working order.

If you experience any unresolvable technical issues with the product, contact your nearest John Lewis & Partners shop or John Lewis & Partner Technical Support on 03301 230106.

Specification

Recommended Bulb: G9 halogen or G9 LED
Max wattage: 33W each bulb
Max. power: 5X33W
Voltage: 220 –240V, 50/60Hz
IP rating: 20
Weight:  5.5kg

5 year guarantee
AtJohn Lewis& Partners we test every lightto high quality standards so we are able to offer you a 5 year guarantee.

Recycling
This symbol   indicates that this product should not be treated as l household waste and it should be recycled. John Lewis & Partners do not operate instore take back, but as members of the Distributor Take Back scheme have funded the development and upgrade of recycling facilities across the UK. Please take it to your nearest collection facility or for further details contact your local council or visit www.recycle-more.co.uk.

John Lewis Partnership 171 Victoria Street London SW1E 5NN www.johnlewis.com
Made inChina
Please retain these instructions for future reference

Documents / Resources

JOHN LEWIS 238928457 Stella Ceiling Light [pdf] User Guide
238928457, Stella Ceiling Light

Leave a comment

Your email address will not be published.