Instruction Manual for EVAWOO models including: DC5V LED Bluetooth Symphony, DC5V, LED Bluetooth Symphony, Bluetooth Symphony
EVAWOO Corner TV Stand LED, Universal TV Mount Stand for 32-65" TV, Height Adjustable Swivel TV Console Wood & Steel Entertainment Center with Mount, Cabinet, Power Outlet, Colorful LED Light, Black : Home & Kitchen
LED Bluetooth Symphony Controller Product Description Download App Software Please search LED LAMP in major Appcenters, or scan below QR code. Technical Parameters Product name Bluetooth Symphony Controller Support system Android 4.4 and above / iOS 11.0 and above Connection mode Bluetooth 4.0 Input voltage DC5V/12V/24V Remote control 17-key Light bar interface Mode + OFF Brightness plus Speed plus Color switch plus Music mode plus/minus ON Brightness minus AUTO mode Speed minus Mode Color switching minus Timing 1 hour 2 hours off Music sensitivity plus/minus Plastic piece Note The plastic sheet isolate the battery. remove the plastic sheet when using the remote control 1. Download the "LED LAMP" APP with your mobile phones by scanning the QR code on user manual or search the "LED LAMP" APP in iPhone APP store or Google play store. 2. After the APP are downloaded successfully, you need to turn on Bluetooth function on your phone firstly, then plug in the strip light, then open the APP, your APP will pair with the strip light automatically and you can control it. Unable to Connect Troubleshooting (1) Check if the power supply of the light strip is normal. (2) Check if the Bluetooth is turn on. (3) Check if there are other mobile phone are connected, Bluetooth 4.0 only support connections one to many, dose not support many to many. (4) Check APP Bluetooth setting if the phone is connected to the device, if connect, exit the APP and reopen, the APP will go to connect automatically. (5) Normal operations and can not connect, please exit the APP and reopen. (6) Exit APP, restart mobile phone, power on the strip light, reopen the APP, then them will connect automatically. First of all, you need to turn on the Bluetooth function of your mobile phone. Android phone users, also turn on the location function and allow permissions. Instructions On the home page, manually pull down to refresh, the APP will automatically search for nearby devices, and click the "LED DMX 00-XXXX" device to enter the lighting control interface. Pull down refresh 2. RGB: There are three parts: color ring, channel and monochrome. Device List Connections RGB value Setting On/off Color selection Color wheel switch Custom color 5. Music: There are voice control and music, there are hundreds of modes for voice control, and music needs to be played by mobile phones. Voice control mode Mode switching Song list add song 1. Settings: You can set RGB sorting, timing, shaking, and changing skins. RGB sort 3. Mode: select the desired mode, custom mode, and adjust the speed and brightness. 4. Custom: You can customize the color, select the mode, adjust the speed and brightness. 6. Settings: Timing settings, click the "Add" button at the top right, after setting, click "Storage", and then "Send Timing". Add timer Play/Pause Cycle Adjustment sort Set pixels Mode selection Mode switch ASSEMBLY INSTRUCTIONS 10 4 11 1 59 9 7 8 83 2 6 1 4 20min ASSEMBLY INSTRUCTIONS 1 2 3 1PC 1PC 1PC 4 5 6 2PCS 1PC 1PC 7 8 9 1PC 2PCS 10 11 1PC 1PC 2 2PCS ASSEMBLY INSTRUCTIONS No. A B C D E F G H 3# PICTURE Tool sheet SIZE QTY No. M6*25 14 AA M6*30 2 BB M6*40 8 CC ST5*40 8 DD ST4*12 2 EE M6*30 2 FF M8 8 GG X2 X2 X2 4# 1 HH 1 II X1 X2 1 PICTURE SIZE QTY M8*70 4 M8*50 4 M8*10 4 M5*45 2 M8*16 4 M6*16 4 16x6.5x1.0mm 16 4 16x8.5x1.0mm 16 4 16x8.5x5.0mm 16 4 2 Matters needing attention (1)When installing the screws in the installation step, the screws do not need to be tightened. After this installation step is confirmed and the holes are aligned, then tighten all the screws. (2)If the screws are tightened during the installation process, it will cause problems such as misalignment of the screw holes and misalignment of the board in subsequent installations. example Do not tighten the screws 3 Screw down G M8 1 6PCS ASSEMBLY INSTRUCTIONS 5 4 4 4 G G G G G G G C M6*40 2 4PCS C 6 C 4 6 C 4 4 Pay attention to the hole 7 position C C 4 F M6*30 3 2PCS ASSEMBLY INSTRUCTIONS 9 9 F 7 F 7 9 F 7 F 7 C M6*40 4 2PCS 5C C 9 9 5 D ST5*40 5 4PCS 4 D ASSEMBLY INSTRUCTIONS 5 2 D 4 D D A M6*25 6 3PCS A6 2 A A 6 ASSEMBLY INSTRUCTIONS B M6*30 C M6*40 7 2PCS 2PCS C 8 2 B C 7 8 8 B Pay attention to the hole position 211.5 191.5 D ST5*40 8 4PCS D 8 8 3 D D D5 7 E ST4*12 9 2PCS E 3E 10 ASSEMBLY INSTRUCTIONS E 10 E 3 A 10 M6*25 11PCS 1 9 A9 7A A A A A A 4A A A A 4 8 11 11 12 ASSEMBLY INSTRUCTIONS 1 Carefully remove the plastic film behind the light strip. 11 1 11 9 BB 13 M8*50 4PCS BB BB BB BB ASSEMBLY INSTRUCTIONS Hold still BB BB BB BB CC 14 M8*10 4PCS CC CC CC CC Hold still The nub has non-slip rubber. Tighten the screws hard. CC CC CC 10 CC G M8 15 2PCS ASSEMBLY INSTRUCTIONS G G AA 16 M8*70 4PCS AA AA 5 AA AA G G AA AA 5 11 Hold still ASSEMBLY INSTRUCTIONS 17 EE/FF M8*16/M6*16 GG/HH 4PCS 16x6.5x1.0mm II 16x8.5x5.0mm 16x8.5x1.0mm 4PCS 4PCS EE/FF EE/FF GG/HH GG/HH II TV II EE/FF GG/HH EE/FF EE/FF II GG/HH GG/HH TV II II EE/FF GG/HH II 18 TV 12 DD 19 M5*45 2PCS ASSEMBLY INSTRUCTIONS DD DD DD 20 Pay attention to the assembly location lamp 13 ASSEMBLY INSTRUCTIONS 21 22 wall 14 H 23 X2 1PC ASSEMBLY INSTRUCTIONS H H H H 24 X2 X2 1PC Installlation completed H H H H 15Corel PDF Engine Version 14.0.0.701