導入
This manual provides detailed instructions for the installation, operation, and maintenance of your Nextbase Click&Go PRO Powered Mount. This mount is designed to securely hold your Nextbase Series 2 Dash Cam, offering both 3M adhesive and suction cup fitting methods for versatile placement in your vehicle. The integrated power connection allows for a wireless dash cam setup.
主な特徴:
- Dual Fitting Methods: Includes both a 3M adhesive pad and a suction cup for flexible installation.
- 幅広い互換性: Compatible with Nextbase Dash Cams including 122, 222, 322GW, 422GW, 522GW, and 622GW models.
- 磁気アタッチメント: Utilizes high-strength neodymium magnets for easy and secure attachment/removal of the dash cam.
- ワイヤレス電力： Power cable connects directly to the mount, enabling a wireless connection to the dash cam.
- 調整可能性： The 3M adhesive pads come in a pack of two for repositioning, and the suction cup allows for easy relocation.
セットアップとインストール
Before installation, ensure your windshield is clean and dry. Choose a location that does not obstruct your view 道路から外れたり、エアバッグに干渉したりする可能性があります。
Method 1: 3M Adhesive Pad Installation
- 表面の準備: Clean the chosen area on your windshield thoroughly with an alcohol wipe and allow it to dry completely.
- 接着剤を塗布する: Remove the protective film from the 3M adhesive pad on the mount.
- ポジションマウント: Firmly press the mount onto the cleaned windshield surface for at least 30 seconds. Apply pressure to ensure a strong bond.
- Allow Adhesion: For optimal adhesion, allow the mount to set for at least 24 hours before attaching the dash cam or driving.
Image: The Nextbase Click&Go PRO mount showing the red 3M adhesive pad on its base.
画像: 別の view of the Nextbase Click&Go PRO mount with the 3M adhesive pad.
Method 2: Suction Cup Installation
- 表面の準備: Clean the chosen area on your windshield thoroughly with an alcohol wipe and allow it to dry completely.
- 吸盤を取り付ける: Ensure the suction cup lever is in the open position. Press the suction cup firmly against the windshield.
- セキュアマウント： Flip the lever to the closed position to create a vacuum seal, securing the mount to the windshield.
Image: The Nextbase Click&Go PRO mount, showing the grey foam pad which is part of the suction cup mechanism.
電源接続
Once the mount is securely installed, connect the power cable (not included with mount, typically supplied with dash cam) directly into the power port on the mount. This allows the dash cam to receive power wirelessly when attached.
操作手順
Attaching Your Dash Cam
Align the magnetic connector on the back of your Nextbase Dash Cam with the magnetic plate on the Click&Go PRO mount. The strong neodymium magnets will securely snap the dash cam into place, establishing both physical and power connections.
Video: Demonstrates how to easily attach a Nextbase Dash Cam to the Click&Go PRO Magnetic Mount.
Detaching Your Dash Cam
To remove your dash cam, gently pull it away from the magnetic mount. The magnetic connection allows for quick and easy detachment when needed.
メンテナンス
- クリーニング： マウントの清掃には、柔らかく乾いた布をご使用ください。研磨剤入りの洗剤や溶剤は使用しないでください。
- 粘着パッド: If using 3M adhesive, avoid frequent removal and reapplication as this can weaken the bond. Replacement pads are available if needed.
- 吸盤: Periodically check the suction cup for dust or debris. Clean with water and allow to air dry if the suction weakens.
- 温度： Extreme temperatures can affect adhesive and suction performance. Ensure the vehicle interior is at a moderate temperature during installation and for optimal long-term use.
トラブルシューティング
| 問題 | 解決 |
|---|---|
| Mount is not sticking (3M adhesive). | Ensure the windshield surface was clean and dry before application. Apply firm pressure for at least 30 seconds. Allow 24 hours for the adhesive to cure. If the issue persists, use a new 3M adhesive pad. |
| Mount is not sticking (suction cup). | Clean the windshield and the suction cup thoroughly. Ensure the lever is fully engaged to create a vacuum seal. Avoid oily or textured surfaces. |
| ダッシュカムに電源が供給されていません。 | Verify the power cable is securely connected to the mount. Ensure the dash cam is correctly aligned and fully seated on the magnetic plate. Check the vehicle's power outlet. |
| ダッシュ カメラがマウント上で緩んでいるように感じます。 | Ensure the dash cam is fully engaged with the magnetic plate. Check for any debris between the dash cam and the mount that might prevent a secure connection. |
仕様
| 特徴 | 詳細 |
|---|---|
| ブランド | ネクストベース |
| モデル名 | Click & Go PRO |
| モデル番号 | NBDVRS2PM |
| 色 | 黒 |
| 取り付けタイプ | Dashboard or Windshield (via 3M Adhesive or Suction Cup) |
| 対応デバイス | Nextbase Series 2 Dash Cams (122, 222, 322GW, 422GW, 522GW, 622GW) |
| アイテム重量 | 40グラム |
| エンクロージャ材質 | アルミニウム |
| 追加機能 | Wireless power connection to dash cam |
保証情報
This Nextbase Click&Go PRO Powered Mount comes with a 90日間の保証 from the date of purchase. This warranty covers manufacturing defects under normal use. It does not cover damage caused by misuse, accidents, unauthorized modifications, or improper installation. Please retain your proof of purchase for warranty claims.
サポート
For further assistance, technical support, or to inquire about replacement parts, please visit the official Nextbase web公式サイトをご覧いただくか、カスタマーサービスまでお問い合わせください。詳細情報と連絡先は、 Nextbase Store on Amazon.