Rhino Rack RL150GMC Leg Brackets User Manual

1. はじめに

The Rhino-Rack RL Leg Brackets (Model RL150GMC) are heavy-duty legs specifically designed for mounting roof rack systems to vehicle gutter mounts. These legs provide a secure and stable foundation for carrying various loads on your vehicle's roof. The RL150GMC model offers a 150mm height, suitable for vehicles requiring medium clearance. These legs are built for durability and compatibility with a wide range of Rhino-Rack accessories, including those for light off-road use.

2. 安全情報

• 運転する前に必ずすべてのコンポーネントがしっかりと固定されていることを確認してください。
• Do not exceed the maximum load capacity of your vehicle's roof or the roof rack system. Refer to your vehicle's owner's manual for specific load limits.
• Regularly check all bolts, nuts, and straps for tightness, especially after initial installation and before long trips.
• Distribute weight evenly across the roof rack to maintain vehicle stability.
• 荷物を運ぶとき、特にガレージ、洗車場、または低いスペースに入るときは、車両の高さと幅が増加することに注意してください。
• Avoid sudden maneuvers, hard braking, or sharp turns when carrying heavy or bulky items.
• For off-road use, reduce speed and exercise extreme caution.

3. パッケージ内容

The Rhino Rack RL150GMC Leg Brackets package typically includes the following components:

• RL Leg Brackets (x2)
• 取り付け金具（ボルト、ナット、ワッシャー）
• Rubber Gaskets/Pads for protection
• End Caps for crossbars
• Rubber Strips for crossbar channels
• Necessary Tools (e.g., Allen key, wrench)
• 取り付け手順（このマニュアル）

4. 仕様

5.インストールガイド

Follow these steps carefully for proper installation of your Rhino Rack RL150GMC Leg Brackets. It is recommended to have a second person assist during installation.

5.1. Prepare the Crossbars and Brackets

1. Identify the front and rear crossbars. The pointed end of the crossbar should face towards the rear of your vehicle, and the round end towards the front.
2. Install the short screws onto the brackets, but do not tighten them fully at this stage.
3. Carefully pull out a section of the rubber strip from the back of the crossbar.
4. Slide the brackets onto the crossbar with the loosened screws.
5. Attach the sponge pad to the base foot of each bracket.
6. Insert the metal end caps into the ends of the crossbars and secure them with the provided screws.

5.2. マーキングと穴あけ

重要： Before drilling, ensure there are no roof supports or cross braces where your holes will be. Measure carefully.

7. Position the assembled crossbars on your vehicle's roof to determine the desired locations for the leg brackets.
8. Use a pen or marker to accurately draw the location of the holes to be drilled on the vehicle's roof, corresponding to the bracket positions.
9. Using an appropriate drill bit, carefully drill holes at the marked locations.

5.3. Securing the Brackets

10. Align each bracket above its drilled hole.
11. Insert the long screw through the bracket and into the drilled hole in the roof.
12. From the inside of the vehicle (or underside of the roof), install the nut and washer onto the screw.
13. Apply waterproof caulking to all important spots around the drilled holes and screws to prevent water leakage.
14. Adjust the position of the brackets as needed and then securely tighten all screws.

5.4.インストールビデオ

視覚的なガイダンスについては、次のインストール ビデオを参照してください。

6. 操作手順

Once the RL Leg Brackets and associated crossbars are securely installed, you can begin using your roof rack system.

• 貨物の積載: Place items on the crossbars, ensuring even weight distribution. Use appropriate tie-downs or cargo straps to secure all items firmly.
• アクセサリの互換性: The RL Leg Brackets are compatible with a wide range of Rhino-Rack accessories. Ensure any accessories used are correctly installed and rated for your intended load.
• 重量制限: Always adhere to the maximum load capacity of your roof rack system and your vehicle. Overloading can lead to damage or unsafe driving conditions.
• 荷物を積んだ状態での運転： Drive cautiously, especially at higher speeds or in windy conditions. Increased drag and weight can affect vehicle handling and fuel efficiency.

7. メンテナンス

Proper maintenance will ensure the longevity and safe operation of your Rhino Rack RL150GMC Leg Brackets.

• 定期検査: Periodically check all bolts, nuts, and mounting points for tightness. Re-tighten as necessary.
• 清潔さ: Clean the leg brackets and crossbars regularly with mild soap and water to remove dirt, grime, and road salt. Avoid harsh chemicals that may damage the finish.
• ゴム部品: Inspect rubber gaskets and strips for wear, cracks, or damage. Replace if necessary to maintain proper sealing and friction.
• 腐食防止: If operating in corrosive environments (e.g., coastal areas, salted roads), rinse the system frequently and apply a corrosion inhibitor to metal parts.
• 季節ごとの削除: If the roof rack is not used for extended periods, consider removing it to reduce wear and tear and improve fuel efficiency.

8。 トラブルシューティング

以下に、一般的な問題とその潜在的な解決策をいくつか示します。

• 問題: 過度の風切り音
  解決： Ensure all rubber strips are properly seated in the crossbar channels. Check that the crossbars are correctly positioned and tightened. Some wind noise is normal with roof rack systems.
• Issue: Loose Components
  解決： Re-check and tighten all mounting bolts and screws. Ensure the leg brackets are firmly seated on the vehicle's gutter mounts.
• Issue: Water Leakage Around Mounting Points
  解決： Verify that waterproof caulking was applied correctly during installation. Reapply or add more caulking if gaps are present. Ensure all washers and nuts are securely tightened.
• 問題: アクセサリの取り付けが困難
  解決： Ensure you are using compatible Rhino-Rack accessories. Check that the T-slots in the crossbars are clear of debris and that accessory mounting hardware is correctly aligned.

9. 保証とサポート

The Rhino Rack RL150GMC Leg Brackets come with a 5年間のメーカー保証この保証は、通常の使用およびサービスにおける材料および製造上の欠陥をカバーします。

For warranty claims, technical support, or further assistance, please contact Rhino-Rack USA, LLC directly or visit their official webサイトでご確認ください。保証を有効にするために購入証明書を保管してください。

詳細については、公式ウェブサイトをご覧ください。 Rhino Rack Store.