Intermatic TN111CL Lamp & Appliance Timer User Manual

1. はじめに

This manual provides instructions for the safe and efficient operation of your Intermatic TN111CL Lamp & Appliance Timer. Please read these instructions thoroughly before using the device and retain them for future reference. The TN111CL timer is designed to automatically turn lamps and appliances ON and OFF at preset times, offering convenience and energy management.

2. 安全に関する注意事項

• 屋内使用のみ: This timer is intended for indoor use in dry locations. Do not expose to rain or moisture.
• 電気定格： Do not exceed the electrical ratings of the timer. Refer to the 'Specifications' section for details. Overloading the timer can cause overheating and fire.
• 接地: Ensure the timer is plugged into a properly grounded outlet.
• 子供たち： 小児の手の届かない場所に保管。 これはおもちゃではありません。
• クリーニング： Unplug the timer from the wall outlet before cleaning. Use a dry cloth; do not use liquid cleaners.
• 修理: Do not attempt to repair or disassemble the timer. Refer all servicing to qualified service personnel.

3.製品オーバーview

The Intermatic TN111CL is a mechanical timer featuring an easy-set dial for scheduling ON/OFF operations. It is designed for use with various lamps and small appliances.

主な特徴:

• 2 ON/OFF settings per 24-hour period.
• Easy-Set Dial for simple programming.
• Minimum ON/OFF time: 1/2 hour.
• Maximum ON/OFF time: 23 1/2 hours.

製品図:

図1: 前面 view of the Intermatic TN111CL Lamp & Appliance Timer, showing the central dial and outlet.

4. セットアップ

1. タイマーを差し込む: Insert the timer into a standard 125V AC wall outlet.
2. 現在の時刻を設定: Rotate the entire dial clockwise until the current time aligns with the arrow indicator on the timer's face. The dial is marked in 15-minute increments. Ensure you distinguish between AM and PM hours (e.g., 3 PM is 15:00 on a 24-hour clock).
3. Plug In Appliance: lを差し込むamp or appliance you wish to control into the outlet on the side of the timer. Ensure the appliance's power switch is in the ON position.

5. 操作手順

The TN111CL timer uses a series of pins around the dial to set ON and OFF times.

1. ピンを識別する: The dial has segments that can be pushed inwards or pulled outwards. Each segment represents 15 minutes.
2. オン時間の設定: To set a period when the appliance should be ON, push the corresponding segments (pins) inwards. For example, if you want the appliance ON from 6:00 PM to 10:00 PM, push in all the pins between the 18:00 and 22:00 marks on the dial.
3. オフ時間の設定: To set a period when the appliance should be OFF, pull the corresponding segments (pins) outwards. These are the default positions for the pins.
4. 手動オーバーライド: The timer typically has a manual override switch (often a small slider or button) that allows you to turn the connected appliance ON or OFF independently of the timer settings. Refer to the markings on your specific unit for its location and function (e.g., 'Timer ON', 'Timer OFF', 'Always ON').

The timer will cycle through the programmed ON/OFF settings daily. The minimum ON or OFF duration is 30 minutes (two 15-minute segments).

6. メンテナンス

• クリーニング： To clean the timer, unplug it from the wall outlet. Wipe the exterior with a soft, dry cloth. Do not use abrasive cleaners, solvents, or immerse the unit in water.
• ストレージ： If storing the timer for an extended period, unplug it and keep it in a cool, dry place away from direct sunlight and extreme temperatures.
• 検査： Periodically inspect the timer and its cord for any signs of damage, such as frayed wires or cracks. If damage is found, discontinue use and replace the unit.

7。 トラブルシューティング

• プログラムされた時間に機器の電源がオン/オフにならない:
  • Ensure the timer is plugged firmly into a working outlet.
  • Verify the appliance plugged into the timer is switched to the ON position.
  • Check that the current time is correctly set on the dial.
  • Confirm that the ON/OFF pins are correctly pushed in (ON) or pulled out (OFF) for the desired times.
  • 手動オーバーライドスイッチの位置を確認します。
• Timer makes a ticking sound:
  • This is normal for mechanical timers and indicates the internal clock mechanism is operating.
• Appliance remains ON or OFF constantly:
  • Check the manual override switch. It may be set to 'Always ON' or 'Always OFF'.
  • Re-verify the pin settings for your desired ON/OFF schedule.

8. 仕様

9. 保証とサポート

保証：

This Intermatic TN111CL Lamp & Appliance Timer comes with a 生涯保証保証請求のために購入証明書を保管してください。

カスタマーサポート:

For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact Intermatic customer support directly. Refer to the official Intermatic web最新の連絡先情報については、サイトまたは製品パッケージをご覧ください。