KMAG HB1 QUICK START GUIDE
KMAG HB1
This guide provides instructions for setting up and using your KMAG HB1 portable Bluetooth speaker.
Key Features:
- 60W Powerful and Crystal Clear Sound
- IP67 Waterproof
- 7 Music Rhythm Lights
60W Powerful and Crystal Clear Sound
The KMAG HB1 features high-quality materials and upgraded chips for an enhanced audio experience. It offers 7 different light modes that sync with the music.
Function Panel
The function panel allows for easy control of your speaker. Buttons include:
- Power On/Off (Press for 3s)
- Volume Up/Down
- Previous/Next Song
- Play/Pause
- TWS (True Wireless Stereo)
- Mode (Switch between BT, USB, AUX)
- BASS Boost
Upgraded BT 5.3
Experience faster and more stable signal with Bluetooth 5.3 connectivity.
How to Connect BT
- Turn on both speakers.
- Turn on the "BT" Button.
- Turn on your phone's BT Settings, search for and connect to "KMAG-GO".
TWS Mode
Synchronize two KMAG HB1 speakers for a true wireless stereo experience, doubling your audio enjoyment.
How to Use TWS Mode
- Turn on both speakers.
- Activate TWS mode on both devices by pressing the TWS button.
- When both speakers emit a prompt tone, they have successfully connected. Connect your phone's Bluetooth as described in "How to Connect BT".
Note: The speaker that plays the first prompt tone is the HOST, and the other is the SLAVE. When using a USB connection, plug the USB into the HOST speaker to play music.
Troubleshooting
If you encounter issues, try these steps:
- Disconnect all functions and reconnect the machine.
- Disconnect your phone's Bluetooth and "Forget" the device in your phone's BT settings.
- Turn off the BT speaker, wait 5 seconds, and turn it back on.
- Repeat the steps for connecting TWS if necessary.
- Repeat the steps for connecting to Bluetooth.
Recharging and Compatibility
The KMAG HB1 supports quick charging and wide application compatibility.
- ① AUX Jack: Used for audio connectivity (e.g., Phone/Mic/PC/TV).
- ② USB Jack: Used for audio connectivity (e.g., Flash drive) and phone charging.
- ③ Type-C Jack: Used for connecting to power supplies.
What's in The Box
- BT Speaker x 1
- User Manual x 1
- AUX Connecting Cable x 1
- USB-C Charging Cable x 1
TECH SPEC
| Specification | Details |
|---|---|
| Wireless Level | 5.3 |
| Output Power | 2 x 30 W RMS |
| Battery Charge Time | 5 Hours (Requires a 5V/2A Adaptor connected to the Type C Jack on the Machine) |
| Battery Type | Li-ion Polymer 37 Wh (equivalent to 3.7V/10000 mAh) |
| Music Play Time | Up to 24 Hours (Depending on volume level and audio content) |
| Transducer | 67.7mm x 43mm |
| Frequency Response | 20Hz-20kHz |
| Signal-to-Noise Ratio | >80dB |
| 2.4GHz SRD Frequency Range | 2407MHz-2475MHz |
| SRD Transmitter Power | <11dBm (ERP) |
| Dimensions (WxHxD) | 14.3 x 4.9 x 6.8 inches |
| Weight | 4.17 lbs |
Important Notes:
- Please fully charge the BT speaker before every use, especially upon first receipt.
- To improve battery life, charge it at least once every 3 months.
- Use in a dry environment with moderate temperature and volume is conducive to extending the product's service life.
- Avoid liquids and water when the BT speaker is connected to any cable. Charging while wet can damage the speaker. It is recommended to charge after the product is completely dry.
- To clean stains, wipe with a paper towel or wet paper towel; do not rinse directly with water.
- Clean the product immediately after use in a pool or ocean to prevent damage to the waterproof seal or connector surface from chemicals or particles.
- When using an external adapter, the output voltage/current should not exceed 5V / 2A.
Warranty Information:
The KMAG product is covered by a 12-month warranty. For inquiries or assistance, please contact KMAG customer support.