PRG-MUL2 - InventronicsApplication Notes - Inventronics
Owner's Manual for inventronics models including: SSM-760S15AMGR, SSM-760S15AMGR 760W Programmable Driver with INV Digital Dimming, 760W Programmable Driver with INV Digital Dimming, Programmable Driver with INV Digital Dimming, Driver with INV Digital Dimming, INV Digital Dimming, Digital Dimming, Dimming
File Info : application/pdf, 15 Pages, 819.32KB
DocumentDocumentSSM-760SxxxMGR Rev.B 760W Programmable Driver with INV Digital Dimming Features Panel Mount Connectors Facilitates Installation Rotary Switch+RJ12 Connector Hot-plugging Protection Parallel LED Protection Ultra High Efficiency (Up to 95%) Full Power at Wide Output Current Range (Constant Power) Adjustable Output Current (AOC) with Programmability Isolated 0-10V/PWM/Resistor/3-Timer-Modes Dimmable Adjustable Dimming Curve INV Digital Dimming, UART Based Communication Protocol Dim-to-Off Minimum Dimming Level with 5% or 10% Selectable Hold Time Adjustable Fade Time Adjustable Low Inrush Current Output Lumen Compensation End-of-Life Indicator Input Surge Protection: DM 6kV, CM 10kV All-Around Protection: IOVP, IUVP, OVP, SCP, OTP IP66 and UL Dry/Damp/Wet Location 5 Years Warranty Description The SSM-760SxxxMGR series is a 760W, constant-current, programmable and IP66 rated LED driver that operates from 249-528Vac input with excellent power factor. Created for many lighting applications including high mast, sports, UV-LED, aquaculture and horticulture, etc. It provides rotary switch, RJ12 connector and dim-to-off functionality. The dimming control supports 0-10V dimming as well as two-way communication via Digital Dimming, a UART based communication protocol. The high efficiency of these drivers and compact metal case enables them to run cooler, significantly improving reliability and extending product life. To ensure trouble-free operation, protection is provided against input surge, input under voltage, input over voltage, output over voltage, short circuit, and over temperature. Models Adjustable Output Current Range(A) Full-Power Current Range(A)(1) Default Output Current(A) Output Voltage Range(Vdc) Max. Output Power(W) Typical Efficiency(2) Typical Power Factor 277Vac 480Vac Model Number(3)(4) 1.4-15.8 14-15.8 14A 34-54 760W 95.0% 0.99 0.96 SSM-760S15AMGR Notes: (1) Output current range with constant power at 760W. (2) Measured at 100% load and 480Vac input (see below "General Specifications" for details). (3) Certified voltage range: UL, FCC 277-480Vac; otherwise: 277-400Vac. (4) SELV output. Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 1 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGR Rev.B 760W Programmable Driver with INV Digital Dimming I-V Operating Area 60 54 (1400, 54) (8400 , 54 ) (10%Ioset, 760/Ioset) 48 42 (14000 , 54 ) (Ioset, 760/Ioset) (15800 , 48 ) Output Voltage(V) 36 30 24 0 (1580, 34) Good Performance Area Programmed Operating Area (15800, 34) (Ioset, 34 ) Allowed Operating Area 3160 6320 9480 12640 15800 Output Current (mA) Note : 14000mAIoset15800mA 18960 Input Specifications Parameter Input AC Voltage Input DC Voltage Input Frequency Leakage Current Input AC Current Inrush Current(I2t) PF THD Min. 249 Vac 352 Vdc 47 Hz - 0.90 - Typ. - Max. Notes 528 Vac 500 Vdc 63 Hz 0.75 MIU 0.70 mA 3.24 A 1.87 A 1.80 A2s 20% UL 8750; 480Vac/60Hz IEC 60598-1; 480Vac/60Hz Measured at 100% load and 277 Vac input. Measured at 100% load and 480 Vac input. At 480Vac input, 25C cold start, duration=6.06 ms, 10%Ipk-10%Ipk. At 277-480Vac,50-60Hz, 60%-100%Load (456 - 760W) Output Specifications Parameter Min. Output Current Tolerance Output Current Setting(Ioset Range) SSM-760S15AMGR Output Current Setting Range with Constant Power SSM-760S15AMGR Total Output Current Ripple (pk-pk) Output Current Ripple at < 200 Hz (pk-pk) Startup Overshoot Current -5%Ioset 1400 mA 14000 mA - Typ. - - 5%Iomax - Max. 5%Ioset 100% load Notes 15800 mA 15800 mA 10%Iomax 100% load, 20 MHz BW 2%Iomax 70%-100% load 10%Iomax 100% load Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 2 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGR Rev.B 760W Programmable Driver with INV Digital Dimming Output Specifications (Continued) Parameter No Load Output Voltage SSM-760S15AMGR Line Regulation Min. - Typ. - Load Regulation - - Turn-on Delay Time - - Temperature Coefficient of Ioset - 0.03%/C Max. Notes 60 V ±0.5% ±3.0% 0.5 s - 100% load Measured at 277-480Vac input, 60%100% Load Case temperature = 0C ~Tc max General Specifications Parameter Efficiency at 277 Vac input: SSM-760S15AMGR Io= 14000 mA Io= 15800 mA Efficiency at 400 Vac input: SSM-760S15AMGR Io= 14000 mA Io= 15800 mA Efficiency at 480 Vac input: SSM-760S15AMGR Io= 14000 mA Io= 15800 mA Standby Power Min. 91.5% 91.5% 92.5% 92.5% 93.0% 93.0% - Typ. 93.5% 93.5% 94.5% 94.5% 95.0% 95.0% 1.5 W Max. - - - MTBF - 224,000 Hours - Lifetime Operating Case Temperature for Safety Tc_s Operating Case Temperature for Warranty Tc_w Storage Temperature Dimensions Inches (L × W × H) Millimeters (L × W × H) Net Weight - -40°C -40°C -40°C 111,000 Hours 50,000 Hours - - - - +90°C +80°C +85°C 15.35 × 4.25 × 1.91 390 × 108 × 48.5 - 3360 g - Notes Measured at 100% load and steady-state temperature in 25C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Measured at 100% load and steady-state temperature in 25C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Measured at 100% load and steady-state temperature in 25C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Measured at 480Vac/50Hz; Dimming off Measured at 480Vac input, 80%Load and 25C ambient temperature (MIL-HDBK217F) Measured at 480Vac input, 80%Load and 70C case temperature; See lifetime vs. Tc curve for the details Measured at 277Vac input, 100%Load and 40C ambient temperature Case temperature for 5 years warranty Humidity: 10%RH to 95%RH Humidity: 5%RH to 95%RH With mounting ear 16.34 × 4.25 × 1.91 415 × 108 × 48.5 Dimming Specifications Parameter Absolute Maximum Voltage on the Vdim (+) Pin Source Current on Vdim (+)Pin Min. -20 V 90 uA Typ. - 100 uA Max. 20 V 110 uA Notes Vdim(+) = 0 V Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 3 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGR Rev.B 760W Programmable Driver with INV Digital Dimming Dimming Specifications (Continued) Parameter Min. Dimming Output Range with 10%-100% (Default) SSM-760S15AMGR SSM-760S15AMGR Dimming Output Range with 5%-100% (Settable) SSM-760S15AMGR SSM-760S15AMGR Recommended Dimming Input Range Dim off Voltage 10%Ioset 1400 mA 5%Ioset 700 mA 0 V 0.35 V Dim on Voltage 0.55 V Hysteresis - PWM_in High Level 3 V PWM_in Low Level -0.3 V PWM_in Frequency Range 200 Hz PWM_in Duty Cycle PWM Dimming off (Positive Logic) PWM Dimming on (Positive Logic) PWM Dimming off ( Negative Logic) PWM Dimming on ( Negative Logic) Hysteresis 1% 3% 5% 92% 90% - Typ. - - - 0.5 V 0.7 V 0.2 V 5% 7% 95% 93% 2% Max. Notes Ioset 14000 mA Ioset 15800 mA Ioset 1400 mA Ioset 14000 mA Ioset 14000 mA Ioset 15800 mA Ioset 10 V 0.65 V 0.85 V 10 V 0.6 V 3 KHz 99% 8% 10% 97% 95% - 1400 mA Ioset 14000 mA Default 0-10V dimming mode. Dimming mode set to PWM in Inventronics Programing Software. Safety &EMC Compliance Safety Category Standard UL/CUL CE CB UL 8750,CAN/CSA-C22.2 No. 250.13 EN 61347-1, EN 61347-2-13 IEC 61347-1, IEC 61347-2-13 EMI Standards Notes EN IEC 55015(1) Conducted emission Test &Radiated emission Test EN IEC 61000-3-2 Harmonic current emissions EN 61000-3-3 Voltage fluctuations & flicker ANSI C63.4 Class B FCC Part 15(1) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: [1] this device may not cause harmful interference, and [2] this device must accept any interference received, including interference that may cause undesired Operation. Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 4 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGR Rev.B 760W Programmable Driver with INV Digital Dimming Safety &EMC Compliance (Continued) EMS Standards Notes EN 61000-4-2 Electrostatic Discharge (ESD): 8 kV air discharge, 4 kV contact discharge EN 61000-4-3 Radio-Frequency Electromagnetic Field Susceptibility Test-RS EN 61000-4-4 Electrical Fast Transient / Burst-EFT EN 61000-4-5 Surge Immunity Test: AC Power Line: Differential Mode 6 kV, Common Mode 10 kV EN 61000-4-6 Conducted Radio Frequency Disturbances Test-CS EN 61000-4-8 Power Frequency Magnetic Field Test EN 61000-4-11 Voltage Dips EN 61547 Electromagnetic Immunity Requirements Applies To Lighting Equipment Note: (1) This LED driver meets the EMI specifications above, but EMI performance of a luminaire that contains it depends also on the other devices connected to the driver and on the fixture itself. Lifetime(kHours) Lifetime vs. Case Temperature Lifetime vs. Case Temperature 135 120 105 90 75 60 45 30 15 0 30 35 40 45 50 55 60 65 70 75 80 85 90 Case Temperature () Inrush Current Waveform I Ipeak 50% Ipeak twidth Input AC Voltage Ipeak twidth (@ 50% Ipeak) 480V 19.9A 1.84ms t Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 5 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGR Rev.B 760W Programmable Driver with INV Digital Dimming Efficiency vs. Load SSM-760S15AMGR(lo=14000mA) 100% Efficiency vs. Output Voltage 100% SSM-760S15AMGR(lo=15800mA) Efficiency vs. Output Voltage 95% 95% Efficiency PF Efficiency 90% 90% 85% 80% 75% 60% 277Vac 400Vac 480Vac 70% 80% 90% 100% Normalized Output Voltage 85% 80% 75% 60% 277Vac 400Vac 480Vac 70% 80% 90% 100% Normalized Output Voltage Power Factor PF vs. Load 1.00 0.95 0.90 0.85 0.80 0.75 60% 70% 80% Load 277Vac 400Vac 480Vac 90% 100% Total Harmonic Distortion 20% THD vs. Load 15% THD 10% 5% 0% 60% 70% 80% Load 277Vac 400Vac 480Vac 90% 100% Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 6 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGR Rev.B 760W Programmable Driver with INV Digital Dimming Hot-plugging Protection This feature protects LEDs when connecting to a driver that is already powered on. This is disabled by default and can be enabled through the Inventronics Programing Software. LED threshold voltage (Vth) is the minimum voltage required for current to flow through the LED load. After this threshold is met, the LED forward voltage (Vf) increases as the current increases. Set Vth close to, but higher than the actual LED threshold voltage for optimized performance. The greater the difference between the Vth setting and the actual LED threshold voltage, the higher the overshoot current will be. The Vth setting must be lower than Vf. Please test, program, and tune this feature for each LED load design. Parameter Hot-plugging Protection LED Threshold Voltage Setting Range Setting Tolerance Min. 44 V -2% Typ. - Max. 54 V 2% Notes Set Vth close to, but higher than the actual LED threshold voltage Parallel LED Protection This feature helps protect parallel LEDs from a high, overcurrent condition by limiting the voltage. This is disabled by default and can be enabled through the Inventronics Programing Software. Set V_overload close to, but higher than the maximum forward voltage for optimized performance. The greater the difference between the V_overload setting and the maximum forward voltage, the higher the overload stress will be. The V_overload setting must be higher than Vf. Please test, program, and tune this feature for each LED load design. Parameter Parallel LED Protection Overload Voltage Setting Range Setting Tolerance Min. 47 V -2% Typ. - Max. 56 V 2% Notes Set V_overload close to, but higher than the maximum LED forward voltage Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 7 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGR Rev.B 760W Programmable Driver with INV Digital Dimming Protection Functions Parameter Min. Typ. Max. Notes Over Temperature Protection Decreases output current, returning to normal after over temperature is removed. Short Circuit Protection Auto Recovery. No damage will occur when any output is short circuited. The output shall return to normal when the fault condition is removed. Over Voltage Protection Limits output voltage at no load and in case the normal voltage limit fails. Input Under Voltage Protection (IUVP) Input Over Voltage Protection (IOVP) Input Protection Voltage Input Recovery Voltage Input Over Voltage Protection Input Over Voltage Recovery Max. of Input Over Voltage 220 Vac 230 Vac 550 Vac 530 Vac - 230 Vac 240 Vac 570 Vac 550 Vac - 240 Vac 250 Vac 590 Vac 570 Vac 590 Vac Turn off the output when the input voltage falls below protection voltage. Auto Recovery. The driver will restart when the input voltage exceeds recovery voltage. Turn off the output when the input voltage exceeds protection voltage. Auto Recovery. The driver will restart when the input voltage falls below recovery voltage. The driver can survive for 8 hours with a stable input voltage stress of 590Vac. Note: When removing the protective cap of RJ12, the waterproof protection performance should be evaluated together with external connected system by users. Input Under Voltage Protection Diagram Io Recovery Protection 230 Vac Input Over Voltage Protection Diagram Io Recovery Vin 240 Vac Protection 550 Vac Vin 570 Vac Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 8 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGR Rev.B 760W Programmable Driver with INV Digital Dimming Rotary Switch and RJ12 Connector Output current can be set as 0, 40%, 60%, 80%, 100% level by rotary switch and the output current can be dimmed by dimming wire in RJ12 connector when rotary switch is at 'EXT' position. The default mode is in 'EXT' Rotary Switch Pin Function 1,6 Vprg 2,5 Dim+ 3,4 Dim- RJ12 Connector Dimming 0-10V Dimming The recommended implementation of the dimming control is provided below. Io/Ioset vs. Dimming Voltage Inventronics LED Driver V+ VVprg Dim+ Dim- Dimmer Io/Ioset 100% 80% 60% 40% 20% 0% 0 1 2 3 4 5 6 7 8 9 10 Dimming Voltage (V) Implementation 1: Positive logic Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 9 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGR Rev.B 760W Programmable Driver with INV Digital Dimming Inventronics LED Driver Io/Ioset vs. Dimming Voltage 100% V+ 80% Io/Ioset V- 60% Vprg Dim+ 40% 20% Dim- Dimmer 0% 012345678 Dimming Voltage (V) Implementation 2: Negative logic 9 10 Notes: 1. Do NOT connect Dim- to the output V- or V+, otherwise the driver will not work properly. 2. The dimmer can also be replaced by an active 0-10V voltage source signal or passive components like zener. 3. When 0-10V negative logic dimming mode and Dim+ is open, the driver will dim to off and be standby. PWM Dimming The recommended implementation of the dimming control is provided below. lo/loset vs. PWM duty cycle Inventronics LED Driver V+ VVprg Dim+ Dim- 100% 80% lo/loset 60% PWM Signal 40% 20% 0% 0% 20% 40% 60% 80% PWM duty cycle Implementation 3: Positive logic 100% Inventronics LED Driver lo/loset vs. PWM duty cycle V+ VVprg 100% 80% 60% lo/loset Dim+ Dim- PWM Signal 40% 20% 0% 0% 20% 40% 60% 80% PWM duty cycle Implementation 4: Negative logic 100% Notes: 1. Do NOT connect Dim- to the output V- or V+, otherwise the driver will not work properly. 2. When PWM negative logic dimming mode and Dim+ is open, the driver will dim to off and be standby. Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 10 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGR Rev.B 760W Programmable Driver with INV Digital Dimming Resistor Dimming The recommended implementation of the dimming control is provided below. lo/loset vs. Rx Inventronics LED Driver V+ 100% V- 80% lo/loset Vprg 60% Dim+ 40% Rx Dim- 20% 0% 0k 10k 20k 30k 40k 50k 60k 70k 80k 90k 100k Rx () Implementation 5: Positive logic Inventronics LED Driver lo/loset vs. Rx V+ 100% V- 80% lo/loset 60% Vprg Dim+ 40% Rx Dim- 20% 0% 0k 10k 20k 30k 40k 50k 60k 70k 80k 90k 100k Rx () Implementation 6: Negative logic Notes: 1. Do NOT connect Dim- to the output V- or V+, otherwise the driver will not work properly. 2. When resistor negative logic dimming mode and Dim+ is open, the driver will dim to off and be standby. Adjustable Dimming Curve 0-10V dimming curve can be set as corresponding dimming voltage by Inventronics Multi Programmer. Take the positive logic dimming as an example, the recommended implementation of the dimming control is provided below. Inventronics LED Driver Io/Ioset vs. Dimming Voltage 100% Y V+ 80% VVprg Dim+ Dim- Dimmer Io/Ioset 60% 40% 20% X 0% 012345678 Dimming Voltage(V) Implementation 7: Positive logic 9 10 Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 11 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGR Rev.B 760W Programmable Driver with INV Digital Dimming Notes: 1. Do NOT connect Dim- to the output V- or V+, otherwise the driver will not work properly. 2. The dimmer can also be replaced by an active 0-10V voltage source signal or passive components like zener. 3. When dimming voltage X point is set to be smaller than Y point, the dimming curve is positive logic; conversely, when X point is set to be bigger than Y point, the dimming curve is negative logic. 4. For best dimming accuracy, the difference between X point and Y point is advised more than 4V. 5. Dimming off voltage adjustable. Time Dimming Time dimming control includes 3 kinds of modes, they are Self Adapting-Midnight, Self AdaptingPercentage and Traditional Timer. Self Adapting-Midnight: Automatically adjusts the dimming curve based on the on-time of past two days (if difference <15 minutes), assuming that the center point of the dimming curve is midnight local time. Self Adapting-Percentage: Automatically adjusts the on-time of each step by a constant percentage = (actual on-time for the past 2 days if difference <15 min) / (programmed on-time from the dimming curve). Traditional Timer: Follows the programmed timing curve after power on with no changes. Output Lumen Compensation Output Lumen Compensation (OLC) may be used to maintain constant light output over the life of the LEDs by driving them at a reduced current when new, then gradually increasing the drive current over time to counteract LED lumen degradation. Minimum Dimming Level with 5% or 10% Selectable The minimum dimming level can be set as 5% or 10% by Inventronics Multi Programmer,10% is default. Hold Time Adjustable When AC power is first applied to the LED driver, enabling a "Hold" period can allow devices powered by the Auxiliary voltage to stabilize before the driver fades up to the maximum dimming level. During this period, the driver will not respond to external dimming commands but will respond again after the hold time ends. Both the initial dimming percentage and the duration of this hold period can be adjusted by the Inventronics Multi Programmer. This function is disabled by default. Fade Time Adjustable There is a "Fade" period after the "Hold" period. The soft-start time and dimming slope applied to all dimming transitions can be adjusted individually. It is adjusted by the Inventronics Multi Programmer. This function is disabled by default. End Of Life End-of-Life (EOL) is providing a visual notification to a user that the LED module has reached the end of manufacturer-specified life and that the replacement is recommended. Once active, an indication is given at each power-up of the driver, which the driver indicates this through a lower light output during the first 1 minute before normal operation is continued. Digital Dimming Inventronics Digital Dimming is a UART (Universal Asynchronous Receive Transmitter) based communication protocol. Please refer to Inventronics Digital Dimming file for details. Daisy Chain Application Daisy chain system can support synchronous dimming of up to 100 drivers due to unique dimming interface design, please pay attention to right sequence of `IN' and `OUT' port for RJ12 connection. Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 12 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGR Rev.B 760W Programmable Driver with INV Digital Dimming Daisy chain controlled by External Controller Inventronics supports daisy chain connection for drivers that is dimmed by external controller. All drivers' rotary switch need to be tuned to 'EXT'. Programming Connection Diagram Daisy chain controlled by Driver-self Inventronics offers the solution to use driver itself to control daisy chain dimming without the controller. The rotary switch of the master driver is tuned to required dimming level when the rest of drivers are tuned to `EXT'. Note: The driver does not need to be powered on during the programming process. Please refer to PRG-MUL2 (Programmer) datasheet for details. Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 13 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGR Rev.B Mechanical Outline INPUT(Panel Connector 3P Male) L2/N L1/L 760W Programmable Driver with INV Digital Dimming Rotary Switch RJ12 Socket Dustproof Plug Tc V+ V- OUTPUT(Panel Connector 3P Female) PROJ: Unspecified tolerance:±1 Note: This driver features UL Wet Location, IP66 panel mount connectors to streamline wiring in the field while still supporting stringent environmental conditions. The mating push-lock are not supplied by Inventronics. Please contact Wieland and Amphenol LTW or one of their suppliers for assistance sourcing the mating pushlock. Location Vin Vo Series Wieland RST20i3 Rating voltage/current 600V/10A PN of connector on driver 96.032.1055.7 ALTW X-Lok,C-Size 300V/20A CC-03PMFS-QC800P PN of mating push-lock 96.031.0055.7 (Spring) or 96.031.4055.7 (Screw) CC-03BFMB-QL8APP RoHS Compliance Our products comply with reference to RoHS Directive (EU) 2015/863 amending 2011/65/EU, calling for the elimination of lead and other hazardous substances from electronic products. Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 14 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com SSM-760SxxxMGR Rev.B Revision History Change Date Rev. Item 2023-02-10 A Datasheet Release Format Feature 2023-12-28 Safety &EMC Compliance B Inrush Current Waveform Dimming Mechanical Outline 760W Programmable Driver with INV Digital Dimming Description of Change From / / / / / / / To / Updated Updated Updated Updated Updated Updated Specifications are subject to changes without notice. www.inventronics-co.com Tel: 86-571-56565800 15 / 15 All specifications are typical at 25C unless otherwise stated. Fax: 86-571-86601139 sales@inventronics-co.com