KRAMER VW-4 4 HDMI Output Cascading Video Wall Driver
Controlla cosa c'è nella scatola
- VW-4 4 Output Video-Wall Driver
- 1 Adattatore di alimentazione e cavo
- 1 set di staffe
- 4 piedini in gomma
- 1 Guida rapida all'avvio
Get to know your VW-4
| # | caratteristica | Funzione |
| 1 | LED ACCESO | Si illumina in verde quando il dispositivo è alimentato. |
| 2 | LED DI INGRESSO | Lights green when a valid input signal is detected on the input. |
| 3 | OUTPUT LEDs (1 to 4) | Light green when an acceptor is detected on that output. |
| 4 | INPUT HDMI Connector | Collegati a una sorgente HDMI. |
| 5 | LOOP HDMI Connector | Connect to an additional VW 4 device for configuring a large video wall or to a local monitor. |
| 6 | SERVICE USB Port | Use to perform firmware upgrade. |
| 7 | OUT HDMI Connectors (1 to 4) | Connect to up to 4 HDMI acceptors that make up the video wall configuration. The appropriate segments of the zoomed picture are output on these connectors for connection to the displays in the video-wall.
The output on these connectors is at 1080P resolution. |
| 8 | CONFIGURAZIONE DIP-switch a 4 vie | For fast, basic configuration of the device without needing to be connected to a PC, see Passo 6: Configure VW-4. |
| 9 | RS-232 3-pin terminal block connector | Use to setup and monitor the VW 4 via the Windows software and to upgrade the firmware. |
| 10 | Connettore ETHERNET RJ-45 | Collegarsi a un PC tramite una LAN per configurare e monitorare il VW 4 via the configuration app. |
| 11 | Connettore CC 5V | Collegare all'adattatore di alimentazione in dotazione. |
Mount VW-4
Install VW-4 using one of the following methods:
- Fissare i piedini in gomma e posizionare l'unità su una superficie piana.
- Fasten a bracket (included) on each side of the unit and attach it to a flat surface (see www.kramerav.com/downloads/VW-4)..
- Mount the unit in a rack using the recommended rack adapter (see www.kramerav.com/product/VW-4).
PERICOLO
- Assicurarsi che l'ambiente (ad es. temperatura ambiente massima e flusso d'aria) sia compatibile con il dispositivo.
- Evitare carichi meccanici irregolari.
- Per evitare il sovraccarico dei circuiti, è necessario tenere in considerazione i valori nominali della targa dati dell'apparecchiatura.
- È necessario mantenere una messa a terra affidabile delle apparecchiature montate su rack.
- L'altezza di montaggio massima per il dispositivo è di 2 metri.
Connetti ingressi e uscite
The three devices in this 6×2 diagram are designated 0, 1 and 2. Each output is designated by the device number and its outputs. For example, VW-4 (1) is the second device in this video wall configuration and VW-4 (1-2) is HDMI OUT 2 on that device. 
Collegare l'alimentazione
Connect the power adapter to VW-4 and plug it into the mains electricity. Safety Instructions (See www.kramerav.com for updated safety information) Caution:
- Per i prodotti con terminali relè e porte GPI\O, fare riferimento al rating consentito per un collegamento esterno, situato accanto al terminale o nel Manuale dell'utente.
- All'interno dell'unità non sono presenti parti riparabili dall'operatore.
avvertimento
- Utilizzare solo il cavo di alimentazione fornito con l'unità.
- Scollegare l'alimentazione e scollegare l'unità dalla parete prima dell'installazione.
Configure VW-4
Configure VW-4 via
- DIP-switch settings – for basic video wall configuration.
- VW-4 app, via the Ethernet or RS-232.
- In remoto, tramite comandi seriali RS-232 trasmessi da un sistema touch screen, PC o altro controller seriale.
Controllo RS-232 / Protocollo 3000 Baud Rate: 115,200 Parità: Nessuna Bit di dati: 8 Formato del comando: ASCII Bit di stop: 1 Example: (Set Auto-sync Off to Fast): #SCLR-AS 1,2 Parametri Ethernet predefiniti Indirizzo IP: 192.168.1.39 Gateway: 192.168.0.1 Maschera di sottorete: 255.255.0.0 Porta TCP n.: 5000
Video Wall Configuration via DIP-switch Settings
You can use the DIP-switch settings to quickly configure a basic video wall (without bezel correction) of up to 4×4, consisting of 1 or more VW-4 devices.
When the video wall size is configured using the DIP-switches, it is not possible to set it up via the configuration app. (To use the app, make sure that the DIP-switches are all OFF).
| DIP 1 | DIP 2 | DIP 3 | DIP 4 | Columns x Rows Layout | Note |
| OFF | OFF | OFF | OFF | Basic setup is not used (default) | |
| OFF | OFF | OFF | ON | Full size picture (“1×1” wall) | Image appears on all displays. |
| OFF | OFF | ON | OFF | N/A | |
| OFF | OFF | ON | ON | N/A | |
| Una VW 4 Dispositivo | |||||
| OFF | ON | OFF | OFF | 2×2 wall (0) | |
| OFF | ON | OFF | ON | 4×1 wall (0) | |
| OFF | ON | ON | OFF | 1×4 wall (0) | |
| OFF | ON | ON | ON | N/A | |
| Tre VW 4 dispositivi | |||||
| ON | OFF | OFF | OFF | 3×3 wall, first unit (0) | |
| ON | OFF | OFF | ON | 3×3 wall, second unit (1) | |
| ON | OFF | ON | OFF | 3×3 wall, third unit (2) | |
| ON | OFF | ON | ON | N/A | |
| quattro VW 4 dispositivi | |||||
| ON | ON | OFF | OFF | 4×4 wall, first unit (0) | |
| ON | ON | OFF | ON | 4×4 wall, second unit (1) | |
| ON | ON | ON | OFF | 4×4 wall, third unit (2) | |
| ON | ON | ON | ON | 4×4 wall, fourth unit (3) | |
Video Wall Configuration via the configuration app
Use the VW-4 Windows® Control Software app to configure a video wall of up to 8×8, consisting of 1 or more VW-4 devices (see www.kramerav.com/product/VW-4#Tab_Resources).
To configure the video wall (for example, a 3×2 video wall, using 2 devices)
- 1. Download the latest VW-4 Control Software app from www.kramerav.com/product/VW-4#Tab_Resources.
- Apri l'app.
- Fare clic su Connessione.
The Connection window opens, showing a list of all the connected VW-4 devices and the available RS-232 ports on your PC. The Connection window opens.
- Select a device under All Units and click . The selected device moves to the Selected Units area.
- Add the other connected devices.
- Fare clic su OK.
- Select the Settings tab and then select the Output tab.
- If you need to change the device ID, enter the new ID under ID-NAME and press Enter on your keyboard.
You can set the ID number individually only when the device is directly connected to your PC. The ID number is set to each device, and according to that number each device is assigned its physical position in the video wall setup. - View the sink status of each device output and:
- Set OSD Info.
- Define Auto-Sync Off status.
- Set the HDCP per output and click Save.
- Seleziona la scheda Layout.
- Set the video wall size by either:
- Selecting Column and Row numbers (for example, 3 x 2). OR
- Clicking Quick Selection for common video wall configurations.
- Select horizontal and vertical bezel corrections (in pixels).
For each connected device, VW-4 App also enables performing factory reset, upgrading the firmware, viewing network settings and copying the EDID to the input from a selected EDID source.
Documenti/Risorse
 |
KRAMER VW-4 4 HDMI Output Cascading Video Wall Driver [pdf] Guida per l'utente VW-4, 4 HDMI Output Cascading Video Wall Driver, VW-4 4 HDMI Output Cascading Video Wall Driver, Video Wall Driver, Wall Driver, Driver |
