Prodotto finitoview
The Lewmar Pro-Series Fastening Kit (Metric) is designed as a direct replacement and essential component for installing or maintaining Lewmar Pro-Series 700/1000 and Pro-Fish 700/1000 Windlasses. This kit includes all necessary metric fasteners and a base mat to ensure a secure and proper installation.
Figura 1: Components of the Lewmar Pro-Series Fastening Kit. This image displays the base mat, three threaded rods (metric fasteners), three nuts, and three washers included in the kit.
Contenuto del kit
Verify that all components listed below are present in your kit before beginning installation.
- 1 x Base Mat
- 3 x Metric Threaded Rods
- 3 x Metric Nuts
- 3 x Metric Washers
Figura 2: Labeled components of the fastening kit, highlighting the base mat and metric fasteners.
Configurazione e installazione
This kit is intended for securing Lewmar Pro-Series 700/1000 and Pro-Fish 700/1000 Windlasses to the deck of a vessel. Refer to your specific windlass manual for detailed installation instructions, as this kit provides the fastening hardware.
- Preparazione: Ensure the mounting surface on the deck is clean, flat, and structurally sound. Identify the correct mounting holes for your windlass model.
- Base Mat Placement: Position the base mat (gasket) between the windlass and the deck. This mat helps to seal the mounting area and reduce vibration. Align the holes in the base mat with the windlass and deck mounting holes.
- Inserire elementi di fissaggio: Insert the metric threaded rods through the windlass base, the base mat, and the deck. Ensure they pass through cleanly.
- Fissare con rondelle e dadi: From underneath the deck (or access point), place a washer onto each threaded rod, followed by a nut.
- Stringere: Hand-tighten all nuts initially. Then, using appropriate tools, gradually tighten each nut evenly to secure the windlass firmly to the deck. Avoid over-tightening, which can damage the deck or windlass base. Consult your windlass manual for specific torque specifications.
Figura 3: Representative image showing Lewmar windlasses installed on a boat deck, illustrating the typical application of this fastening kit.
Considerazioni operative
While this kit provides the fastening hardware, proper operation of your windlass relies on a secure installation. Regularly inspect the fastening points for any signs of loosening or corrosion.
- Ensure all nuts remain tight to prevent movement of the windlass during operation.
- Check for any water ingress around the mounting holes, which could indicate an issue with the base mat seal.
- Refer to your specific Lewmar windlass manual for operational guidelines, safety precautions, and maintenance schedules related to the windlass itself.
Manutenzione
Regular inspection of the fastening kit components is crucial for long-term reliability.
- Ispezione visiva: Periodically inspect the threaded rods, nuts, and washers for signs of corrosion, wear, or damage.
- Controllo di tenuta: Annually, or more frequently in harsh marine environments, check the tightness of the nuts securing the windlass. Re-tighten if necessary, adhering to the windlass manufacturer's torque specifications.
- Base Mat Integrity: Inspect the base mat for cracks, tears, or signs of degradation. A compromised base mat can lead to water intrusion.
- Pulizia: Keep the area around the windlass base clean and free of debris, salt residue, and marine growth.
Risoluzione dei problemi
Issues related to the fastening kit are typically straightforward.
| Problema | Possibile causa | Soluzione |
|---|---|---|
| Windlass feels loose on deck | Nuts have loosened over time. | Re-tighten the nuts evenly. Consult windlass manual for torque. |
| Water leaking around windlass base | Damaged or improperly seated base mat; loose fasteners. | Check base mat for damage and replace if necessary. Ensure fasteners are tight. Apply marine sealant if required. |
| Corrosion on fasteners | Exposure to marine environment; lack of maintenance. | Clean affected areas. Apply corrosion inhibitor. Consider replacement if corrosion is severe. |
Specifiche
| Attributo | Dettaglio |
|---|---|
| Nome del modello | 66000108 |
| Codice UPC | 743683326561 |
| Marca | Lewmar |
| Componenti inclusi | Base Mat, Metric Threaded Rods, Nuts, Washers |
| Materiale | Plastic (Base Mat), Metal (Fasteners) |
| Peso dell'articolo | 0.21 chilogrammi |
| Dimensioni della confezione dell'articolo | 13.78 x 6.02 x 0.55 pollici |
| Tipo di montaggio | Montaggio sul ponte |
| Compatibilità | Lewmar Pro-Series 700/1000, Pro-Fish 700/1000 Windlasses |
Informazioni sulla garanzia
This product comes with a manufacturer's warranty. For detailed information regarding warranty terms, conditions, and claims procedures, please refer to the official Lewmar website or contact Lewmar customer support directly. Keep your proof of purchase for warranty validation.
Assistenza clienti
For technical assistance, spare parts, or any other inquiries regarding your Lewmar product, please contact Lewmar customer support.
- Websito: Visita il sito ufficiale Negozio Lewmar su Amazon or the main Lewmar corporate website for contact details and resources.
- Informazioni sui contatti: Refer to the Lewmar website for the most current phone numbers and email addresses for customer service in your region.