Introduzione
This manual provides instructions for the proper setup, operation, maintenance, and troubleshooting of your Orbit Heavy Duty Brass Impact Sprinkler on Tripod Base, Model 58308D. Please read these instructions carefully before using the product to ensure safe and efficient operation.
Informazioni sulla sicurezza
Avvertimento: This product contains lead, a chemical known to the State of California to cause cancer and reproductive toxicity. Wash hands thoroughly after handling.
Always ensure the sprinkler is placed on a stable, level surface to prevent tipping. Do not operate the sprinkler near electrical outlets or equipment. Keep children and pets away from the operating sprinkler.
Prodotto finitoview
The Orbit Heavy Duty Brass Impact Sprinkler on Tripod Base is designed for efficient and wide-area watering. It features a durable brass impact sprinkler head mounted on an adjustable tripod for versatile placement and coverage.
Figura 1: Completo view of the Orbit Brass Impact Sprinkler on Tripod Base.
Impostare
- Disimballare i componenti: Carefully remove all components from the packaging. Ensure you have the brass impact sprinkler head and the tripod base.
- Montare il treppiede: Extend the legs of the tripod base to a stable position. The tripod is adjustable from 25 inches to 48 inches in height. Secure the legs using the locking mechanisms.
- Attach Sprinkler Head: Screw the brass impact sprinkler head onto the threaded connection at the top of the tripod base. Hand-tighten until secure.
- Collegare il tubo dell'acqua: Attach a standard garden hose to the inlet connection at the base of the tripod. Ensure a tight connection to prevent leaks.
- Posizione dell'irrigatore: Place the assembled sprinkler in the desired watering area. Ensure the tripod legs are fully extended and stable on the ground.
Figure 2: Close-up of the tripod leg adjustment and locking mechanism.
Figure 3: Detail of the garden hose connection point on the tripod base.
Figure 4: The Orbit sprinkler fully assembled and connected to a hose on a lawn.
Istruzioni per l'uso
- Accendi l'acqua: Slowly turn on the water supply to the garden hose.
- Regola la pressione dell'acqua: Adjust the water pressure at the faucet to achieve the desired spray distance and pattern. The sprinkler is designed to operate effectively within typical residential water pressures.
- Copertura del monitor: Observe the watering pattern to ensure adequate coverage of your desired area.
Regolazioni
The brass impact sprinkler head allows for adjustments to both the spray pattern and distance:
- Distanza di spruzzo: The sprinkler can reach up to 100 feet in diameter. Adjust the diffuser screw on the sprinkler head to change the water stream's break-up and thus the spray distance. Tightening the screw will shorten the distance, while loosening it will increase it.
- Spray Pattern (Partial to Full Circle): The sprinkler can be set for a partial or full 360-degree circle. Adjust the trip collars on the base of the sprinkler head to set the desired arc. For continuous 360-degree rotation, lift the trip lever.
- Altezza del treppiede: The tripod base can be adjusted from 25 inches to 48 inches in height to accommodate different watering needs and plant heights. Loosen the leg clamps, adjust the height, and re-tighten securely.
Manutenzione
- Pulizia: Periodically check the sprinkler nozzle for debris or mineral buildup. Clean with a small brush or needle if necessary to maintain optimal spray performance.
- winterization: Before freezing temperatures, disconnect the sprinkler from the hose and drain all water from the unit. Store the sprinkler in a dry, protected area to prevent damage from freezing.
- Magazzinaggio: When not in use, store the sprinkler in a cool, dry place away from direct sunlight.
Risoluzione dei problemi
| Problema | Possibile causa | Soluzione |
|---|---|---|
| Sprinkler not rotating | Low water pressure, debris in head, trip collars set incorrectly. | Increase water pressure, clean nozzle, adjust trip collars for full circle or desired arc. |
| Modello di spruzzo non uniforme | Clogged nozzle, damaged diffuser. | Clean nozzle, inspect diffuser for damage. |
| Perdita d'acqua dai collegamenti | Loose connections, worn washer. | Tighten hose connections, replace rubber washer if damaged. |
| Limited spray distance | Low water pressure, diffuser screw too tight. | Increase water pressure, loosen diffuser screw. |
Specifiche
| Caratteristica | Dettaglio |
|---|---|
| Numero di modello | 58308D |
| Materiale | Brass (sprinkler head), Metal (tripod) |
| Dimensioni della connessione di ingresso | 0.75 pollici |
| Altezza regolabile | Da 25" a 48" |
| Portata massima | 2.5 galloni al minuto |
| Diametro di copertura | Fino a 100 piedi |
| Modello di spruzzo | Partial to Full Circle (360°) |
Garanzia e supporto
Per informazioni sulla garanzia o supporto tecnico, fare riferimento al sito ufficiale Orbit websito o contattare il servizio clienti Orbit. Conservare la ricevuta d'acquisto per eventuali reclami in garanzia.