Cisco WS-C4948E-F

Cisco Catalyst 4948E 48-Port Gigabit Switch User Manual

Model: WS-C4948E-F

1. Introduzione

This manual provides essential information for the proper installation, operation, maintenance, and troubleshooting of the Cisco Catalyst 4948E 48-Port Gigabit Switch (Model: WS-C4948E-F). Please read this manual thoroughly before using the device to ensure optimal performance and safety.

The Cisco Catalyst 4948E-F Ethernet Switch is designed for server-access switching, offering forty-eight 10/100/1000 Mbps RJ45 downlink ports and four 1/10 Gigabit Ethernet uplink ports. It is optimized for full-featured Top-of-Rack (ToR) data center deployments in a one Rack Unit (1RU) form factor.

2. Informazioni sulla sicurezza

ATTENZIONE: la mancata osservanza di queste istruzioni di sicurezza potrebbe causare incendi, scosse elettriche o altre lesioni o danni.

  • Garantire l'alimentazione voltage matches the local power grid.
  • Non utilizzare l'interruttore in ambienti con calore eccessivo, umidità o polvere.
  • Scollegare sempre l'alimentazione prima di eseguire qualsiasi procedura di manutenzione o installazione.
  • Questo dispositivo deve essere installato da personale qualificato.
  • Garantire una messa a terra adeguata per evitare rischi elettrici.

3. Contenuto della confezione

Verificare che tutti gli articoli siano presenti e in buone condizioni. Se qualche articolo risulta mancante o danneggiato, contattare il fornitore.

  • Cisco Catalyst 4948E 48-Port Gigabit Switch (WS-C4948E-F)
  • Power Cords (quantity may vary based on region)
  • Kit di montaggio su rack
  • Documentazione (Guida rapida, Informazioni sulla sicurezza)
Davanti view of the Cisco Catalyst 4948E 48-Port Gigabit Switch

Figura 1: Fronte view of the Cisco Catalyst 4948E 48-Port Gigabit Switch, showing 48 RJ45 ports and 4 SFP+ uplink ports.

4. Prodotto finitoview

4.1 Pannello frontale

The front panel of the Cisco Catalyst 4948E-F switch features:

  • 48 x 10/100/1000BASE-T RJ45 Ports: For connecting network devices such as servers, workstations, and other switches.
  • 4 x 1/10 Gigabit Ethernet SFP+ Uplink Ports: For high-speed connections to the core network or other switches.
  • LED di stato: Indicatori per lo stato del sistema, l'attività delle porte e l'alimentazione.

4.2 Pannello posteriore

Il pannello posteriore in genere comprende:

  • Dual AC Power Supply Slots: For redundant power supplies.
  • Porta della console: For local management and initial configuration.
  • Porta Ethernet di gestione: For out-of-band management.

5. Configurazione e installazione

5.1 Montaggio su rack

The Cisco Catalyst 4948E-F is a 1U rack-mountable device. Follow these steps to install it in a standard 19-inch equipment rack:

  1. Attach the provided rack-mount brackets to the sides of the switch using the screws supplied with the kit.
  2. Allineare l'interruttore con i montanti del rack e fissarlo utilizzando le viti appropriate.
  3. Ensure adequate airflow around the switch for proper cooling.

5.2 Collegamento di alimentazione

  1. Insert the power cords into the power supply modules at the rear of the switch.
  2. Connect the other end of the power cords to a grounded AC power outlet.
  3. The switch will power on automatically. Observe the system status LEDs.

5.3 Connessioni di rete

  1. Connect Ethernet cables from your network devices (servers, workstations) to the 10/100/1000BASE-T RJ45 ports on the front panel.
  2. For uplink connections, insert SFP or SFP+ transceivers into the 1/10 Gigabit Ethernet SFP+ ports and connect fiber optic cables to your core network.

6. Istruzioni per l'uso

6.1 Configurazione iniziale

For initial configuration, connect a console cable from your management workstation to the console port on the switch's rear panel. Use a terminal emulation program (e.g., PuTTY, Tera Term) with the following settings:

  • Velocità in baud: 9600
  • Bit di dati: 8
  • Parità: Nessuna
  • Stop Bits: 1
  • Controllo del flusso: nessuno

Follow the on-screen prompts to configure basic settings such as IP address, hostname, and management credentials.

6.2 Interfacce di gestione

The switch can be managed via several interfaces:

  • Interfaccia della riga di comando (CLI): Accessible via console, Telnet, or SSH for advanced configuration.
  • Protocollo di gestione di rete semplice (SNMP): For network monitoring and management.
  • HTTPS: Per web-based management (if enabled and configured).

Refer to the Cisco IOS Software Configuration Guides for detailed information on advanced features and configurations.

7. Manutenzione

Una manutenzione regolare garantisce la longevità e le prestazioni ottimali del tuo switch.

7.1 Pulizia

  • Pulire periodicamente la parte esterna dell'interruttore con un panno morbido e asciutto.
  • Ensure ventilation openings are free from dust and obstructions. Do not use liquid cleaners or aerosols.

7.2 Aggiornamenti firmware

Controllare regolarmente il supporto Cisco websito per gli ultimi aggiornamenti del firmware. L'applicazione degli aggiornamenti può migliorare le prestazioni, aggiungere nuove funzionalità e risolvere vulnerabilità di sicurezza. Seguire le procedure ufficiali di Cisco per gli aggiornamenti del firmware.

7.3 Power Supply Redundancy

The switch supports dual hot-swappable AC power supplies. In case of a power supply failure, the redundant unit will take over seamlessly. Replace faulty power supplies promptly to maintain redundancy.

8. Risoluzione Dei Problemi

Questa sezione fornisce soluzioni ai problemi più comuni che potresti riscontrare.

ProblemaPossibile causaSoluzione
L'interruttore non si accende.No power, faulty power cord, or power supply failure.Check power connections. Verify power outlet functionality. Replace power cord or power supply if necessary.
Il LED della porta è spento.No link, faulty cable, or incorrect port configuration.Check cable connection. Replace cable. Verify port status and configuration via CLI.
Cannot access switch via network.Incorrect IP configuration, network connectivity issue, or firewall blocking access.Verify IP address, subnet mask, and gateway. Check network connectivity to the management interface. Ensure no firewall rules are blocking access. Try console access.
Prestazioni di rete lente.Congestione della rete, mancata corrispondenza duplex o cavo difettoso.Check port statistics for errors or collisions. Ensure duplex settings match on both ends. Investigate network traffic patterns.

For more complex issues, consult the Cisco documentation or contact Cisco Technical Assistance Center (TAC).

9. Specifiche

CaratteristicaDettaglio
ModelloWS-C4948E-F
Tipo di dispositivoSwitch - 48 ports - L3 - managed
Tipo di contenitoreRack-mountable - 1U
Porti48 x 10/100/1000BASE-T RJ45 + 4 x 1/10 Gigabit Ethernet SFP+
Capacità di commutazione176 Gbps
IPv4 Switching Performance131 Mpps
IPv6 Switching Performance110 Mpps
Dimensioni tabella indirizzi MAC55K voci
VLAN attive4094
Dimensioni (LxPxA)17.5 pollici x 19.4 pollici x 1.7 pollici (44.45 cm x 49.28 cm x 4.32 cm)
EnergiaCA 120/230 V (50/60 Hz)
Temperatura di esercizioda 32°F a 104°F (da 0°C a 40°C)
Temperatura di conservazioneDa -40°C a 167°C (da -40°F a 75°F)
Umidità di esercizio10 - 90% (senza condensa)
Tempo medio fra i guasti149,261 ore
MaterialeMetallo

10. Garanzia e supporto

10.1 Garanzia limitata

This Cisco Catalyst 4948E-F switch comes with a Garanzia limitata di 90 giorni. This warranty covers defects in materials and workmanship under normal use. For specific terms and conditions, please refer to the warranty documentation provided with your product or contact your vendor.

10.2 Supporto tecnico

For technical assistance, product documentation, or software downloads, please visit the official Cisco support websito: www.cisco.com/support. You may also contact Cisco Technical Assistance Center (TAC) for expert support.

© 2023 Cisco Systems, Inc. Tutti i diritti riservati. Le informazioni contenute nel presente documento sono soggette a modifiche senza preavviso.