Code Alarm CATX4 Keyless Entry Alarm Remote User Manual

1. Prodotto finitoview

The Code Alarm CATX4 is a 4-button replacement transmitter remote designed for use with compatible Code Alarm keyless entry and alarm systems. This remote operates on a 433.92MHz frequency and features a red LED indicator for signal transmission confirmation.

Caratteristiche principali:

• 4-button functionality for various system commands.
• Operates on AM, superheterodyne (SAW), 433.92MHz frequency.
• Equipped with a red LED for visual feedback.
• FCC ID: H5OT49 (also replaces H5OT43).

Figure 1: Code Alarm CATX4 4-Button Keyless Entry Remote. This image displays the black remote with four gray buttons: Lock (closed padlock icon), Unlock (open padlock icon), Mute/Panic (speaker with slash icon), and Remote Start/Trunk Release (circular arrow icon).

2. Istruzioni di programmazione

This section outlines the procedure for programming your CATX4 remote to your Code Alarm system. You will need access to your system's valet switch (programming/override button) to complete this process. Refer to your vehicle's alarm system installation manual for the exact location of the valet switch.

Sistemi compatibili:

• CA1050, CA1051, CA1053
• CA2050, CA2051
• CA5050, CA5051, CA5053, CA5054

Passaggi di programmazione:

1. Assicurarsi che l'accensione del veicolo sia SPENTA.
2. Open the driver's door.
3. Inserire la chiave nell'accensione e girarla in posizione ON.
4. Within 5 seconds, press and release the valet switch once. The system will respond with a chirp or light flash.
5. Press and hold the LOCK button on your new CATX4 remote. Hold until the system chirps or flashes lights to confirm programming.
6. Rilasciare il pulsante BLOCCO.
7. Turn the ignition OFF to exit programming mode. The system will chirp or flash lights to confirm exit.

Nota: If you are programming multiple remotes, repeat step 5 for each additional remote before turning the ignition OFF. All existing remotes must be reprogrammed at the same time; otherwise, they will be erased from the system's memory.

3. Istruzioni per l'uso

The CATX4 remote features four distinct buttons for controlling your vehicle's alarm and keyless entry system:

• Lock Button (Padlock Closed icon): Press to arm the alarm system and lock the vehicle doors.
• Unlock Button (Padlock Open icon): Press to disarm the alarm system and unlock the vehicle doors.
• Mute/Panic Button (Speaker with Slash icon):
  • Press briefly to mute the arm/disarm chirps (if supported by your system).
  • Press and hold for 3 seconds to activate the panic alarm. Press again to deactivate.
• Remote Start/Trunk Button (Circular Arrow icon):
  • Press and hold for 3 seconds to activate the remote start function (if installed and enabled).
  • Press briefly to open the trunk or activate auxiliary output (if installed and enabled).

Nota: The exact functionality of each button may vary depending on your specific Code Alarm system's configuration and installed features.

4. Manutenzione

The CATX4 remote control is powered by two Lithium Metal batteries. When the remote's range decreases significantly or the LED indicator fails to light up, it is likely time to replace the batteries.

Sostituzione della batteria:

1. Aprire con cautela il telecomando casing. Di solito, per farlo, bisogna fare leva sulla cucitura con un piccolo cacciavite a testa piatta.
2. Remove the old batteries, noting their orientation.
3. Insert two new Lithium Metal batteries, ensuring correct polarity.
4. Aggancia il telecomando casing rimetterli insieme in modo sicuro.
5. Test the remote's functionality. If issues persist, refer to the Troubleshooting section.

Attenzione: Dispose of old batteries according to local regulations. Do not expose batteries to excessive heat or fire.

5. Risoluzione Dei Problemi

If you encounter issues with your Code Alarm CATX4 remote, consider the following troubleshooting steps:

• Il telecomando non risponde:
  • Check the battery. Replace if necessary (refer to Section 4: Maintenance).
  • Ensure you are within range of the vehicle's alarm system.
  • Verify that the remote is properly programmed to your system (refer to Section 2: Programming Instructions).
• Errore di programmazione:
  • Confirm you are using the correct valet switch and following the programming steps precisely.
  • Assicurarsi che la batteria del veicolo sia completamente carica.
  • If multiple remotes are being programmed, ensure all are programmed during the same session.
• Funzionamento intermittente:
  • Batteria del telecomando scarica.
  • Interferenze da altri dispositivi a radiofrequenza.
  • Obstructions between the remote and the vehicle.

If problems persist after attempting these steps, it is recommended to contact a professional automotive alarm technician or the Code Alarm customer support for further assistance.

6. Specifiche

7. Garanzia e supporto

For specific warranty information regarding your Code Alarm CATX4 remote, please refer to the documentation provided with your original alarm system or contact the authorized seller from whom you purchased the product. Warranty terms typically vary by region and retailer.

For technical support or further assistance, it is recommended to contact the Code Alarm manufacturer or an authorized service center. You may also reach out to the seller for initial support inquiries.

Produttore: Audiovox