Loctite 5188 Gasket Sealant User Manual

Prodotto finitoview

The Loctite 5188 Gasket Sealant is an anaerobic flange sealant designed for rigid iron, aluminum, and steel flanged mating surfaces. It cures when confined in the absence of air between close-fitting metal surfaces. This product provides a flexible, solvent-resistant seal that will not tear or degrade. It is ideal for sealing close-fitting joints between rigid metal faces and flanges.

Figura 1: A red tube of Loctite 5188 Flange Sealant, 50ml size, with white cap and nozzle. The label clearly shows 'LOCTITE 5188 FLANGE SEALANT' and 'NET 1.69 FL. OZ. (50 ml)'.

Informazioni sulla sicurezza

Always read the Material Safety Data Sheet (MSDS) prior to use. This product contains chemicals that may be harmful if misused. Keep out of reach of children. Use in a well-ventilated area.

• Evitare il contatto con la pelle e gli occhi. In caso di contatto, sciacquare immediatamente con abbondante acqua e consultare un medico.
• Do not ingest. If swallowed, do not induce vomiting; call a physician immediately.
• Indossare adeguati dispositivi di protezione individuale (DPI) come guanti e occhiali di sicurezza.
• Conservare in luogo fresco e asciutto, lontano dalla luce solare diretta e da fonti di calore.

Preparazione della superficie e dell'allestimento

1. Superfici pulite: Ensure all mating surfaces are clean, dry, and free from oil, grease, and old gasket material. Use a suitable solvent cleaner if necessary.
2. Roughen Surfaces (Optional): For best adhesion, lightly abrade smooth surfaces with an abrasive pad or fine sandpaper, then clean again.
3. Verifica adattamento: Verify that the parts to be sealed fit closely together. This product is designed for close-fitting metal surfaces.

Istruzioni per l'uso (applicazione)

1. Distribuire il prodotto: Apply a continuous bead of Loctite 5188 to one of the flange faces. Ensure complete coverage around all bolt holes and mating surfaces.
2. Assemblare parti: Assemble the components immediately after application. Light clamping is recommended to ensure intimate metal-to-metal contact.
3. Tempo di polimerizzazione:
   • Orario dell'incontro: The product will fixture (become tack-free) in approximately 20 minutes at room temperature (22°C / 72°F).
   • Guarigione completa: Full cure is typically achieved within 24 hours.
   • Nota: Cure speed can vary depending on the substrate material, bondline gap, and temperature. Active metals like brass or copper will cure faster, while passive substrates like stainless steel may require an activator (e.g., Loctite 7649) for faster cure.
4. Prova: Allow sufficient cure time before subjecting the assembly to operational pressures or temperatures.

Manutenzione e stoccaggio

• Magazzinaggio: Store the product in its original container in a cool, dry location. Optimal storage temperature is between 8°C and 21°C (46°F and 70°F).
• Durata di conservazione: Refer to the product packaging for specific shelf life information.
• Ripulire: Uncured product can be cleaned with organic solvents. Cured product must be removed mechanically (e.g., scraping).
• Disposizione: Dispose of product and packaging in accordance with local, regional, national, and international regulations.

Risoluzione dei problemi

Specifiche

• Tipo di prodotto: Anaerobic Gasket Sealant
• Numero modello: 1253203
• Volume: 50 ml (1.69 fl. oz.)
• Colore: Rosso
• Intervallo di temperatura: Da -65°C a 300°C (da -54°F a 149°F)
• Orario dell'incontro: Approximately 20 minutes (on steel)
• Tempo di cura completo: 24 ore
• Flessibilità: Altamente flessibile
• Produttore: Loctite (Henkel)
• Country of Manufacturer: Stati Uniti

Informazioni di supporto

For technical assistance, product inquiries, or safety data sheets, please visit the official Loctite websito o contattare il servizio clienti.

Loctite Official Websito: www.loctite.com

Negozio del marchio Amazon: Visit the Loctite Store on Amazon