Behringer Super-X Pro CX3400 Crossover User Manual

1. Prodotto finitoview

The Behringer Super-X Pro CX3400 is a high-precision stereo 2-way/3-way/mono 4-way crossover designed for professional audio applications. It features advanced Linkwitz-Riley filters, individual limiters, phase reverse switches, and a subsonic filter to optimize speaker performance and protect your system.

Caratteristiche principali:

• 24 dB/octave, state-variable Linkwitz-Riley filters for precise frequency separation.
• Absolutely flat summed amplitude response, zero phase difference.
• Individual limiter and phase reverse switch per output.
• Switchable 25 Hz subsonic filter per input for low-frequency driver protection.
• Switchable equalization for constant directivity horns.

2. Controlli del pannello frontale

The front panel of the CX3400 provides intuitive controls for managing your audio signals. It features two main channels and a dedicated subwoofer section, allowing for flexible configuration.

Figura 1: Fronte view of the Behringer CX3400, showing all control knobs and switches for Channel 1, Subwoofer, Mode, and Channel 2.

Controlli:

• Interruttore di alimentazione: Accende o spegne l'unità.
• Manopole di guadagno: Adjust the input and output levels for each channel and the subwoofer.
• Low Cut (40Hz) Switch: Activates a 25 Hz subsonic filter to protect low-frequency drivers.
• Crossover Frequency Knobs: Set the frequency points where the audio signal is divided between different speaker ranges (e.g., low/high, low/mid, mid/high).
• X-Over Freq Switch (x1/x10): Multiplies the selected crossover frequency by 10 for extended range.
• Mode Switch (Stereo/Mono, 2-Way/3-Way): Selects between stereo 2-way, stereo 3-way, or mono 4-way operation.
• Phase Invert Switches: Reverses the phase of individual outputs to correct for acoustic phase issues.
• Limiter Switches: Activates the built-in limiters to prevent signal clipping and speaker damage.

3. Collegamenti del pannello posteriore

The rear panel provides all necessary audio input and output connections, primarily using XLR connectors for balanced signal transmission.

Figura 2: Posteriore view of the Behringer CX3400, showing XLR inputs and outputs for Channel 1 and Channel 2, as well as the power input.

Connessioni:

• Input (XLR): Balanced XLR inputs for Channel 1 and Channel 2, receiving the full-range audio signal from your mixer or source.
• Low Out (XLR): Balanced XLR outputs for low-frequency signals, typically connected to subwoofer amplificatori.
• Mid Out (XLR): Balanced XLR outputs for mid-range frequency signals (available in 3-way and 4-way mono modes).
• High Out (XLR): Balanced XLR outputs for high-frequency signals, typically connected to full-range speaker amplificatori.
• Sub Out (XLR): Dedicated balanced XLR output for summed subwoofer signals.
• Ingresso CA: Connettore di alimentazione IEC standard per il collegamento dell'unità alla rete elettrica.

4. Guida all'installazione

Proper setup of your CX3400 is crucial for optimal audio performance. This section outlines the steps for connecting your crossover in a typical 2-way stereo configuration.

4.1. Basic 2-Way Stereo Setup:

1. Collega la sorgente audio: Connect the main outputs of your mixer or audio source to the INPUTs of Channel 1 and Channel 2 on the CX3400 using XLR cables.
2. Connect Low-Frequency Amplificatore: Connect the LOW OUTs of Channel 1 and Channel 2 on the CX3400 to the inputs of your amplifier(s) driving your subwoofers or low-frequency speakers.
3. Connect High-Frequency Amplificatore: Connect the HIGH OUTs of Channel 1 and Channel 2 on the CX3400 to the inputs of your amplifier(s) driving your full-range or high-frequency speakers.
4. Accensione: Ensure all connections are secure. Power on your mixer, then the CX3400, and finally your amplificatori.

4.2. Mono 3-Way/4-Way Setup:

For mono 3-way or 4-way operation, press the MODE switch to 'MONO'. In this mode, the inputs are summed, and the outputs are reconfigured to provide separate low, mid, and high-frequency signals, plus an additional subwoofer output if selected. Refer to the rear panel labels for specific output assignments in mono mode.

5. Istruzioni per l'uso

Once your CX3400 is connected, fine-tuning the settings will optimize your sound system's performance.

5.1. Setting Crossover Frequencies:

1. Impostazioni iniziali: Start with all GAIN knobs at 0dB and crossover frequency knobs at a neutral position.
2. Adjust Low/High Crossover: For 2-way operation, use the LOW/HIGH X-OVER FREQ knob to set the division point between your low-frequency speakers (subwoofers) and high-frequency speakers (full-range). A common starting point is around 80-120 Hz for subwoofers.
3. Adjust Mid/High Crossover (3-Way/4-Way): In 3-way or 4-way mono modes, additional crossover frequency knobs will be active to separate mid-range and high-frequency signals.
4. Use X-Over Freq Switch: If you need to adjust frequencies outside the standard range, use the x1/x10 switch to multiply the knob's range.

5.2. Gain and Level Adjustment:

1. Guadagno in ingresso: Adjust the INPUT GAIN for each channel to match the output level of your mixer. Avoid clipping (indicated by the CLIP LED).
2. Output Gains: Adjust the LOW OUTPUT, MID OUTPUT, and HIGH OUTPUT GAIN knobs to balance the volume levels of your different speaker components.
3. Guadagno del subwoofer: Use the SUBWOOFER GAIN knob to control the overall level of the subwoofer output.

5.3. Limiter and Phase Control:

• Limitatori: Engage the LIMITER switches on each output to prevent signal peaks from distorting your speakers.
• Phase Reverse: Use the PHASE REVERSE switches if you encounter phase cancellation issues between speakers, which can result in a thin or weak sound.
• Filtro subsonico: Activate the 25 Hz SUBSONIC FILTER to remove extremely low, inaudible frequencies that can waste amplifier power and potentially damage subwoofers.

6. Manutenzione

To ensure the longevity and reliable performance of your Behringer CX3400, follow these maintenance guidelines:

• Pulizia: Pulire regolarmente l'unità con un panno morbido e asciutto. Evitare l'uso di detergenti abrasivi o solventi.
• Ventilazione: Assicurare un adeguato flusso d'aria attorno all'unità. Non ostruire le aperture di ventilazione.
• Magazzinaggio: Conservare l'unità in un luogo fresco e asciutto, lontano dalla luce solare diretta e da temperature estreme.
• Ispezione dei cavi: Periodically check all audio and power cables for damage or wear. Replace any faulty cables immediately.

7. Risoluzione Dei Problemi

If you encounter issues with your CX3400, refer to the following troubleshooting tips:

• Nessun suono:
  • Check all power connections and ensure the unit is turned on.
  • Verificare che tutti i cavi audio siano collegati correttamente agli ingressi e alle uscite.
  • Ensure input and output gain knobs are not set to minimum.
  • Check the MODE switch setting (Stereo/Mono) matches your setup.
• Suono distorto:
  • Reduce input or output gain levels to prevent clipping (if CLIP LEDs are active).
  • Ensure the correct crossover frequencies are set for your speakers.
  • Controllare che i cavi non siano danneggiati o che i collegamenti siano difettosi.
• Weak Bass/Lack of Low End:
  • Check the LOW OUT gain level.
  • Verify the crossover frequency for low-frequency speakers is set appropriately.
  • Ensure the 25 Hz subsonic filter is not inadvertently engaged if you require frequencies below this point.
  • Check phase settings using the PHASE REVERSE switches.

8. Specifiche

9. Informazioni sulla garanzia

For detailed warranty information regarding your Behringer CX3400, please refer to the official Behringer websito:

http://www.music-group.com/warranty.aspx

10. Supporto

Should you require further assistance, have questions, or need technical support for your Behringer CX3400, please contact Behringer customer support through their official channels. Visit the Behringer websito per informazioni di contatto e risorse di supporto.