AJAX - Merki

Notendahandbók sendis
Uppfært mars 22, 2021

AJAX 10306 Transmitter Wired to Wireless Detector Converter - cover

sendandi is a module for connecting third-party detectors to Ajax security system. It transmits alarms and warns about the activation of the external detector tamper and it is equipped with own accelerometer, which protects it from dismounting. It runs on batteries and can supply power to the connected detector.
Transmitter operates within the Ajax security system, by connecting via the protected Jeweller protocol to the hub. It is not intended to use the device in third-party systems.
Not compatible with the uartBridge or ocBridge Plus
The communication range can be up to 1,600 meters provided that there are no obstacles and the case is removed.

Transmitter is set up via a mobile application for iOS and Android based smartphones.

Buy integration module Transmitter

Hagnýtir þættir

AJAX 10306 Transmitter Wired to Wireless Detector Converter - Functional Elements

  1. QR code with the device registration key.
  2. Batteries contacts.
  3. LED vísir.
  4. ON / OFF hnappur.
  5. Terminals for detector power supply, alarm and tamper signals.

Rekstraraðferð

Transmitter is designed to connect third-party wired sensors and devices to the Ajax security system. The integration module receives information about alarms and tamper activation through the wires connected to the clamps.
Transmitter can be used to connect panic and medical buttons, indoor and outdoor motion detectors, as well as opening, vibration, breaking, re, gas, leakage and others wired detectors.
The type of alarm is indicated in the settings of the Transmitter. The text of noti cations about alarms and events of the connected device, as well as event codes transmitted to the central monitoring panel of the security company (CMS) depend on the selected type.

Alls eru 5 tegundir tækja í boði:

Gerð Táknmynd
Innbrotsviðvörun
Brunabjalla
Læknisviðvörun
Læti hnappur
Gasstyrksviðvörun

Transmitter has 2 pairs of wired zones: alarm and tampGer.
A separate pair of terminals ensures power supply to the external detector from the module batteries with 3.3 V.

Tengist miðstöðinni

Áður en tenging hefst:

  1. Following the hub instruction recommendations, install the Ajax application on your smartphone. Create an account, add the hub to the application, and create at least one room.
  2. Farðu í Ajax forritið.
  3. Kveiktu á miðstöðinni og athugaðu nettenginguna (um Ethernet snúru og / eða GSM net).
  4. Gakktu úr skugga um að miðstöðin sé afvopnuð og hefji ekki uppfærslur með því að athuga stöðu hennar í farsímaforritinu.

Aðeins notendur með stjórnunarréttindi geta bætt tækinu við miðstöðina

How to connect the Transmitter to the hub:

  1. Veldu valkostinn Bæta við tæki í Ajax forritinu.
  2. Name the device, scan/write manually the QR Code (located on the body and packaging) and select the location room.
  3. Veldu Bæta við - niðurtalningin hefst.
  4. Switch on the device (by pressing on/off button for 3 seconds).

AJAX 10306 Transmitter Wired to Wireless Detector Converter - How to connect the Transmitter to the hub

For the detection and interfacing to occur, the device should be located within the coverage area of the wireless network of the hub (at a single protected object).
Beiðni um tengingu við miðstöðina er send í stuttan tíma þegar kveikt er á tækinu.
If the connection to the Ajax hub failed, the Transmitter will switch off after 6 seconds. You may repeat the connection attempt then.
The Transmitter connected to the hub will appear in the list of devices of the hub in the application. Update of device statuses in the list depends on the device inquiry time set in the hub settings, with the default value ­ 36 seconds.

States

  1. Tæki
  2. sendandi
Breytu gildi
hitastig Hitastig tækisins. Mælt á örgjörvanum og breytist smám saman
Styrkur skartgripa Signal strength between the hub and the device
Rafhlaða hleðsla Rafhlöðustig tækisins. Birtist sem prósentatage
Hvernig birtist rafhlaða í Ajax forritum
Lok tamper terminal state
Seinkun þegar þú slærð inn, sek Seinka tíma þegar komið er inn
Seinkaðu þegar þú ferð, sek Seinka tíma þegar þú hættir
Tenging Connection status between the hub and the Transmitter
Alltaf virkur f active, the device is always in an armed mode
Tilkynning ef færð It turns on the Transmitter accelerometer, detecting device movement
Tímabundin óvirkjun Sýnir stöðu tímabils óvirkjunaraðgerðar tækisins:
Nr - tækið starfar eðlilega og sendir alla atburði.
Aðeins lok — the hub administrator has disabled noti the device body.
Algjörlega — the device is completely excludedfrom the system operation by the hub administrator. The device does not follow system commands and does not report alarms or other events.
Eftir fjölda viðvörunar — the device is automatically disabled by the system when the number of alarms is exceeded (speci in the settings for Devices Auto Deactivation). The feature is coned in the Ajax PRO app.
Eftir tímastillingu — the device is automatically disabled by the system when the recovery timer expires (speci Devices Auto Deactivation). The feature is
coned in the Ajax PRO app.
Firmware Útgáfa skynjara
tæki ID Tæki auðkenni

Stillingar

  1. Tæki
  2. sendandi
  3. Stillingar
Stilling gildi
First Nafn tækis, er hægt að breyta
Hreinlæti Velja sýndarherbergið sem tækinu er úthlutað
Tengiliðastaða ytri skynjara Selection of the external detector normal status:
• Normally closed (NC)
• Normally opened (NO)
External Detector Type Selection of the external detector type:
• Pulse
• Bistable
Tamper staða Selection of the normal tamper mod for an external detector:
• Normally closed (NC)
• Normally opened (NO)
Gerð viðvörunar Select alarm type of connected device:
• Intrusion
• Eldur
• Medical help
• Panic button
• Gas
The text of SMS and notivents feed, as well as the code transmitted to the security company’s console, depends on the selected type of alarms
Alltaf virkur When the mode is active, the Transmitter transmits alarms even when the system is disarmed
Seinkun þegar þú slærð inn, sek Velja seinkunartíma þegar slegið er inn
Seinkaðu þegar þú ferð, sek Velja seinkunartíma við brottför
Seinkun í næturstillingu Töf er kveikt þegar notast er við næturstillingu
Tilkynning ef færð The accelerometer turning on the Transmitter to provide an alarm in the event of device movement
Aflgjafi fyrir skynjara Turning the power on in 3.3 V external detector:
• Disabled if disarmed
• Always disabled
• Always enabled
Armaðu í næturstillingu Ef það er virkt mun tækið skipta yfir í vopnaða stillingu þegar næturstilling er notuð
Alert with a siren if an alarm is detected If active, Sirens added to the system are sirens activated if an alarm is detected
Styrkleikapróf skartgripasmíðsins Skiptir tækinu yfir í prófunarham fyrir merkjastyrk
Dæmingarpróf Switches the device to the signal fade test mode (available in detectors with firmware version 3.50 and later)
User Guide Opens the device User Guide
Tímabundin óvirkjun Tveir möguleikar eru í boði:
Algjörlega — the device will not execute system commands or run automation
scenarios. The system will ignore device alarms and not
Aðeins lok — messages about triggering the tamper button of the device are ignored
Frekari upplýsingar um tímabundna óvirkjun tækisins
Kerfið getur einnig gert tækin óvirk sjálfkrafa þegar farið er yfir stilltan fjölda viðvörunar eða þegar endurheimtartíminn rennur út.
Frekari upplýsingar um sjálfvirka óvirkjun tækja 
Aftengja tæki Aftengir tækið frá miðstöðinni og eyðir stillingum þess

Set the following parameters in the Transmitter settings:

  • The state of the external detector contact, which can be normally closed or normally open.
  • The type (mode) of the external detector that can be bistable or pulse.
  • tamper mode, which can be normally closed or normally open.
  • The accelerometer-triggered alarm — you can turn this signal off or on.

Select the power mode for the external detector:

  • Turned off when the hub is disarmed — the module stops powering the external detector upon disarming and does not process signals from the
    ALARM terminal. When arming the detector, the power supply resumes, but the alarm signals are ignored for the
  • Always disabled — the Transmitter saves energy by turning off the power of the external detector. The signals from the ALARM terminal are processed both in the pulse and bistable modes.
  • Always active — this mode should be used if there are any problems in the “Turned off when the hub is disarmed”. When the security system is armed, signals from the ALARM terminal are processed no more than once in three minutes in the pulse mode. If the bistable mode is selected, such signals are processed instantly.

If the “Always active” operating mode is selected for the module, the external detector is powered only in the “Always active” or the “Turned off when the hub disarmed” mode, regardless of the security system status.

Vísbending

atburður Vísbending
The Module is switched on and registered The LED lights up when the ON button is brie pressed.
Skráning mistókst LED blinks for 4 seconds with an interval of 1 second, then blinks 3 times rapidly (and automatically switches OFF).
The Module is deleted from the list of hub devices LED blinks for 1 minute with an interval of 1 second, then blinks 3 times rapidly (and automatically switches OFF).
The Module has received alarm/tamper signal The LED lights up for 1 second.
Rafhlöður eru tæmdar Smoothly lights up and goes out when the detector or tamper virkjaður.

Árangurspróf

Ajax öryggiskerfið gerir kleift að gera prófanir til að kanna virkni tengdra tækja.
Prófin byrja ekki strax en innan 36 sekúndna þegar staðlaðar stillingar eru notaðar. Prófunartíminn ræðst af stillingum skönnunartímans skynjara (málsgreinin um „Gimsteinar“ settings in hub settings).

Styrkleikapróf skartgripasmíðsins
Dæmingarpróf

Connection of the Module to the wired detectorа

Location of the Transmitter determines its remoteness from the hub and presence of any obstacles between the devices hindering the radio signal transmission: walls, inserted ge-size objects located within the room.

Check the signal strength level at the installation location

If the signal level is one division, we cannot guarantee stable operation of the security system. Take possible measures to improve the quality of the signal! As a minimum, move the device — even 20 cm shift can signiove the quality of reception.
If, after moving, the device still has a low or unstable signal strength, use a . radio signal range extender ReX
The Transmitter should be encased inside the wired detector case. The Module requires a space with the following minimum dimensions: 110 × 41 × 24 mm. If the installation of the Transmitter within the detector case is impossible, then any available radiotransparent case could be used.

  1. Connect the Transmitter to the detector through the NC/NO contacts (choose the relevant setting in the application) and COM.

The maximum cable length for connecting the sensor is 150 m (24 AWG twisted pair). The value may vary when using different type of cable.

The function of the Transmitter’s terminals

AJAX 10306 Transmitter Wired to Wireless Detector Converter - The function of the Transmitter’s terminals

+ — — power supply output (3.3 V)
VARMARI - alarm terminals
TAMP - tamper terminals

IMPORTANT! Do not connect external power to the Transmitter’s power outputs.
This may damage the device
2. Secure the Transmitter in the case. Plastic bars are included in the installation kit. It is recommendable to install the Transmitter on them.

Do not install the Transmitter:

  • Nálægt málmhlutum og speglum (þeir geta varið útvarpsmerkið og leitt til deyfingar þess).
  • Closer than 1 meter to a hub.

Maintenance and Battery Replacement

The device does not require maintenance when mounted in the housing of a wired sensor.

Hve lengi Ajax tæki starfa á rafhlöðum og hvað hefur áhrif á þetta
Skipta um rafhlöðu

Tech Sérstakur

Connecting a detector ALARM and TAMPER (NO/NC) terminals
Mode for processing alarm signals from the detector Pulse or Bistable
Power 3 × CR123A, 3V batteries
Capability to power the connected detector Yes, 3.3V
Protection from dismounting Accelerometer
Tíðnisviði 868.0–868.6 MHz or 868.7 – 869.2 MHz,
depends on sales region
Eindrægni Operates only with all Ajax , hubs and range extenders
Hámarks RF framleiðsla máttur Allt að 20 mW
mótum GFSK
Samskiptasvið Allt að 1,600 m (allar hindranir ekki)
Ping interval for the connection with the receiver 12–300 sek
Hitastigi Frá –25°С til +50°С
rekstrartekjur raki Allt að 75%
mál 100 × 39 × 22 mm
þyngd 74 g

Heill setja

  1. sendandi
  2. Battery CR123A — 3 pcs
  3. Uppsetningarbúnað
  4. Quick Start Guide

Ábyrgð í

Ábyrgð fyrir „AJAX SYSTEMS MANUFACTURING“ TAKMARKAÐA ÁBYRGÐARFYRIRTÆKI gildir í 2 ár eftir kaupin og gildir ekki fyrir fyrirfram uppsettu rafhlöðuna.
If the device does not work correctly, you should t service — in half of the cases, technical issues can be solved remotely!

Fullur texti ábyrgðarinnar
User Samningur
Tæknilega aðstoð: [netvarið]

Skjöl / auðlindir

AJAX 10306 Transmitter Wired to Wireless Detector Converter [pdf] Notendahandbók
10306, Transmitter Wired to Wireless Detector Converter

Skildu eftir athugasemd

Netfangið þitt verður ekki birt.