Solar Stone Glow

Introduction
Thank you for purchasing the ION Audio Solar Stone Glow! Solar Stone Glow simulates a natural rock finish that blends into your landscaping, with a solar-rechargeable battery-powered, water-resistant speaker. Equipped with Bluetooth® technology, you can listen to your favorite music wirelessly while working in the garden, hosting a dinner party, or relaxing by the pool.

  1. Make sure all items listed in the Box Contents are included in the box.
  2. Read the Safety & Warranty Manual before using the product
  3. Make sure that you have completely charged the battery prior to first use for maximum battery life.

Box Contents

If an individual speaker is purchased:
1 Solar Stone Glow
1 Charging Adapter
Quickstart Guide
Safety & Warranty Manual

If purchased as a boxed pair:
2 Solar Stone Glows
2 Charging Adapters
Quickstart Guide
Safety & Warranty Manual

Support
For the latest information about this product (documentation, technical specifications, system requirements, compatibility information, etc.) and product registration, visit ionaudio.com.
For additional product support, visit ionaudio.com/support.

Rechargeable Batteries
Rechargeable lead-acid batteries are the same type used in automobiles. As with your car battery, how you use this battery has a significant impact on its lifespan. With proper use and treatment, a lead-acid battery can last for years. Here are some recommendations for getting the longest life from the internal battery.

General Usage  Fully charges the battery before using it. Charge the battery completely after each use.

Storage For best product longevity, do not store at exceedingly hot (greater than 90°F/32°C) or exceedingly cold (less than 32°F/0°C) temperatures.
It is acceptable to leave your sound system plugged in. This will not overcharge the battery.
If you leave the battery level low and do not charge it for 6 months, it may permanently lose capacity.

Repair If the battery fails to charge, contact ION Audio at ionaudio.com.

Disposal Bring the unit to a recycling center or dispose of it in accordance with local ordinances.

Outdoor Use and Care
Though Solar Stone Glow is water-resistant and able to tolerate splashing water, please review the tips below to get the best performance from Solar Stone Glow:

  • Bring Solar Stone Glow indoors during extreme cold, heavy rain, or melting snow.
  • Please do not place Solar Stone Glow in standing water.
  • Please do not connect the charging adapter to Solar Stone Glow in a wet environment. Make sure the charging adapter input, charging adapter, and power outlet are all completely dry before making any connections.
  • WARNING: Keep any non-water-resistant devices (phones, music players, etc.) in a dry place where they will not be affected by water and cause a risk of electric shock.

Features

  1. Power: Hold this button to power Solar Stone Glow on and off.Solar Stone Glow - Features
  2. Bluetooth Connect: Press this button briefly to begin Bluetooth connecting.
    Note: Solar Stone Glow will automatically power off after 30 minutes if no audio is playing and the rear LEDs are not on.
  3. Link: Press this button to link two Solar Stone Glow units together.
  4. Light Control: Press this button to adjust the brightness settings for the lights: LED low, LED high, and off.
  5. Charging Adapter Input: Insert the included charging adapter here to charge the Solar Stone Glow battery. Solar Stone Glow should be fully charged prior to first use for maximum battery life. Once fully charged, Solar Stone Glow’s solar panel can provide suitable power for typical daily use without the need to connect the charging adapter. Results will vary depending on the daily number of hours Solar Stone Glow is exposed to direct sunlight.
  6. Reset: If Solar Stone Glow is working abnormally, shut down the unit by placing a paperclip into the Reset hole located on the back of Solar Stone Glow, and gently push until the unit turns off. Try this only after you have first attempted to reboot Solar Stone Glow using the power button.
  7. Charging LED: This LED is solid red when the battery is charging and turns off when the battery is fully charged/no adapter is connected.
  8. Bluetooth LED: This LED slowly blinks blue when the speaker is powered on, blinks fast while Bluetooth searching, and is solid when Bluetooth connected.
  9. Link LED: This LED blinks fast when searching for another Solar Stone Glow and is solid when linked to another Solar Stone Glow.

Bluetooth Connecting with Solar Stone Glow
Connecting to One Solar Stone Glow

  1. Power on Solar Stone Glow by holding down the power button. You will hear “Power On” for confirmation. *
  2. Press the Bluetooth Connect button briefly to enter Connecting Mode–the Bluetooth LED will blink fast, and you will hear “Pairing” to indicate this. *
  3. Navigate to your device’s Bluetooth setup screen, find Solar Stone Glow, and connect. Bluetooth LED will light up solid when it is connected and you will hear “Pairing successful, connected” for confirmation. *
    Note: If you experience trouble in connecting, select “Forget this Device” on your Bluetooth device and try to connect again.
  4. To disconnect, hold the Bluetooth Connect button on Solar Stone Glow. You will hear “Disconnected” for confirmation. *
  5. If your Bluetooth device is not able to connect to Solar Stone Glow, hold the Bluetooth Connect button on the speaker to break previous Bluetooth connections and reset the Bluetooth module.

Linking Two Solar Stone Glows to Each Other for Stereo Sound
Note: Ensure that the speakers are not already Bluetooth-connected in single mode. If either of them is connected, hold the Bluetooth Connect button to disconnect and then follow the steps below.

  1. Power on each Solar Stone Glow by holding down their power buttons. You will hear “Power On” for confirmation. *
  2. Press the Link button on each Solar Stone Glow. The speakers will search for each other while playing an intermittent tone. Once the stereo pair is successfully linked, you will hear “Pairing successful, connected” followed by “Left channel” and “Right channel” on the respective speakers. * This process may take up to 2 minutes the first time two speakers are linked. Speakers that were previously linked will relink automatically in a few seconds if powered on in a range of one another.
    Note: Solar Stone Glows should be within 30 ft. (9 m) of each other to Link properly.
  3. On the left speaker, the Bluetooth LED will blink. Press the Bluetooth Connect button briefly to enter Bluetooth pairing mode. Note: The Left speaker will be the “primary” speaker and the unit from which the Bluetooth range will be determined.
  4. Navigate to your device’s Bluetooth setup screen, find Solar Stone Glow, and connect. You will hear “Connected” for confirmation. *
    Note: If you experience trouble in connecting, select “Forget this Device” for Solar Stone Glow on your Bluetooth device and try to connect again.
  5. To disconnect linking, hold the Link button on the “primary” Solar Stone Glow for 2 seconds. You will hear “Disconnected” for confirmation. *
  6. If your Bluetooth device is not able to connect to Solar Stone Glow, hold the Bluetooth Connect button on the speaker to break previous Bluetooth connections and reset the Bluetooth module.
    Note: When two speakers are linked, hold the power button on the “primary” speaker to turn both speakers off. If you want to only turn off the “secondary” speaker, press and hold the power button on that speaker. The speakers will relink automatically the next time they are both powered on.

* Tip: If you would like to disable (or enable) the voice prompts, simultaneously press the Bluetooth Connect and Link buttons briefly.

FCC Statement
Warning: This product shall be installed and operated with a minimum distance of 20 cm between the radiator and user body.

File Downloads

Instruction Manual
Solar Stone Glow
Download [optimized]
Download

References

Leave a comment

Your email address will not be published.