Categories: INFRATECH COMFORT

INFRATECH COMFORT CDX024SS CD-Series Quartz Tube Electric Infrared Radiant Heater User Manual

INFRATECH COMFORT CDX024SS CD-Series Quartz Tube Electric Infrared Radiant Heater

WARNINGS READ ALL INSTRUCTIONS BEFORE USING HEATER. Unit may be a source of possible shock. NEVER attempt to service heater without disconnecting its power source. Source of possible ignition.

WARNING: If not installed, operated and maintained in accordance with the manufacturer’s instructions, this product can expose you to chemicals including nickel, which are known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov

CAUTION: High Temperature, risk of fire, keep electrical cords, drapery, furnishings and other combustibles at least 3′ (0.9m) from the front of heater and away from sides and rear.

MOUNTING HEIGHT/CLEARANCES

  • For Wall-Mounting, do not install heater closer than 18″ (45.7cm) from adjacent walls and 12″ (30.5cm) from ceiling and do not install less than 6′ (1.8m) if the heater is labeled as UL Listed and 8′ (2.4m), if the heater is labeled as UL/CUL, Listed from floor, while heater is set at a downward angle of 30 to 60 degrees.
  • For Ceiling-Mounting, do not install heater closer than 18″ (45.7cm) from adjacent walls and 6″ (15.2cm) from ceiling and do not install less than 6′ (1.8m) if the heater is labeled as UL Listed and 8′ (2.4m), if the heater is labeled as UL/CUL, Listed from floor, while heater is at a maximum 30 degrees.
  • Adjacent Heaters to be installed no less than 3′ (0.9m) apart.
  • Do NOT operate within 25′ (7.6m) of flammable/explosive material.
  • Never block heater.
  • Heaters greater than 240 Volts are for “Commercial Use Only. Risk of fire. Do not use as a residential or household heater.”
  • A means for disconnection of the appliance must be incorporated in accordance with the local wiring codes.
  • Do not use if the heating element is damaged or cracked.

INSTALLATION INSTRUCTIONS

This heater must be permanently installed and hard-wired by a licensed electrician in accordance with local electrical codes. Assembly procedure must be performed with no electrical power to unit.

  1. Check UL/CUL/CE label on heater for proper voltage.
  2. Follow supplied wiring instructions. (See wiring instructions below)
  3. Heater must be mounted with reflector angled down.
  4. All electrical connections must be in compliance with the National Electric Code (NEC) and local codes for outdoor wiring.
  5. Use only wiring components UL/CUL/CE listed for outdoor use with IPX4 minimum rating.

WIRING INSTRUCTIONS

The heater is drilled and threaded for standard 1/2″ conduit fittings. The installing electrician will need to provide the appropriate rigid metallic, flexible or liquid-tight conduit for the installation location.

  • Observe local electrical code regulations.
  • Remove cover plate from junction box.
  • Attach conduit.
  • Use only copper wire suitable for 90°C.
  • Replace cover plate.

MOUNTING INSTRUCTIONS

These models may be chain or bracket mounted to any ceiling or horizontal surface. Installation must be such that 18″ (45.7cm) minimum clearance is maintained around the heater on all four sides and 36″ (91.4cm) directly in front. A minimum of 6″ (15.24cm) of clearance provided by mounting brackets is required behind the plane of the face. Heater can be hung using chains or custom brackets. Heater must be level, but can be rotated around its horizontal axis.

Heater must be installed with the quartz tube horizontally level. For maximum tube life, use a carpenter’s level tool to fi nd the optimum level position for the heater’s body. It’s important to always maintain the minimum clearances from the heater body to any combustible materials.

REPLACEMENT ELEMENT INSTALLATION

(VISIT INFRATECH-USA.COM FOR VIDEO INSTRUCTIONS)
Disconnect the power at the breaker. Remove the grill by grasping it in the middle, flex grill up, and lift it off. Unscrew and remove both end reflectors. Unhook element clips at each end of the heater and remove nuts from end of element to remove the existing quartz tube. Carefully install the new element. Remove one nut from end of the new element. Install wire by sliding high-temperature ring terminal onto element screw and replace nut. Use a thin 11/32″ wrench to hold inside nut. Nuts must make a tight connection. Close element clips over tube, reinstall end reflectors, then snap protective grill back in place.

NOTE: Hold ceramic element firmly while tightening nut to prevent damage to element. Nut should be tightened snug. A loose connection can cause the element to short or fail prematurely.

REPLACEMENT ELEMENTS

(OTHER VOLTAGES ALSO AVAILABLE)

PART NUMBER ELEMENT NUMBER LENGTH WATTS VOLTS FITS
10-1020 E-7512 16-1/2″ (0.4m) 750 120 C-7512
10-1050 E-1412 30″ (0.8m) 1500 120 C-1512
10-1055 E-1424 30″ (0.8m) 1500 240 C-1524/CD-3024
10-1085 E-2024 36″ (0.9m) 2000 240 C-2024/CD-4024
10-2010 E-2524 36″ (0.9m) 2500 240 C-2524/CD-5024
10-2030 E-3024 58″ (1.5m) 3000 240 C-3024/CD-6024
10-2055 E-4024 58″ (1.5m) 4000 240 C-4024

Consult the label on back of heater for proper watts, voltage, and replacement element part number.

Need help? To order replacement elements for your Infratech heating system, please contact us via phone or visit our website.

REPLACEMENT PARTS

PART NUMBER PART DESCRIPTION QUANTITY
13-1210 Single Element End Reflector (Set of 2) 1
13-1252 Dual Element End Reflector (Set of 2) 1
13-1207, 13-1208, 13-1209 C-Series Body Reflector – Fits 33″ (0.8m), 39″ (1.0m), 61-1/4″ (1.6m) 1
13-1242, 13-1240, 13-1245 Grill Guard – Fits 33″ (0.8m), 39″ (1.0m), 61-1/4″ (1.6m) 1
13-1232, 13-1230, 13-1235 Lead Wire Set – Fits 33″ (0.8m), 39″ (1.0m), 61-1/4″ (1.6m)* 1
13-1250 SS Mounting Bracket (Set of 2) 1

Note: Dual Element Heaters require 2 Lead Wire Sets per Heater

MODEL WATTS MOUNTING HEIGHT AVERAGE COLD PROTECTED
C-1512 SS 1,500 6′ – 7′ (1.8m – 2.4m) 5′ x 5′ (1.5m x 1.5m) 3′ x 3′ (0.91m x 0.91m) 7′ x 7′ (2.1m x 2.1m)
C-2024 SS 2,000 7′ – 8′ (2.1m – 2.7m) 6′ x 6′ (1.8m x 1.8m) 4′ x 4′ (1.2m x 1.2m) 8′ x 8′ (2.4m x 2.4m)
C-2524 SS 2,500 7′ – 8′ (2.1m – 2.7m) 7′ x 7′ (2.1m x 2.1m) 5′ x 5′ (1.5m x 1.5m) 9′ x 9′ (2.7m x 2.7m)
C-3024 SS 3,000 7′ – 9′ (2.1m – 2.7m) 8′ x 8′ (2.4m x 2.4m) 6′ x 6′ (1.8m x 1.8m) 10′ x 10′ (3.0m x 3.0m)
C-4024 SS 4,000 8′ – 10′ (2.4m – 3.4m) 10′ x 10′ (3.0m x 3.0m) 8′ x 8′ (2.4m x 2.4m) 12′ x 12′ (3.7m x 3.7m)
MODEL WATTS MOUNTING HEIGHT AVERAGE COLD PROTECTED
CD-3024 SS 3,000 7′ – 8′ (2.1m x 2.7m) 7′ x 7′ (2.1m x 2.1m) 5′ x 5′ (1.5m x 1.5m) 9′ x 9′ (2.7m x 2.7m)
CD-4024 SS 4,000 8′ – 10′ (2.4m – 3.7m) 8′ x 10′ (2.4m x 3.0m) 6′ x 8′ (1.8m x 2.4m) 10′ x 12′ (3.0m x 3.7m)
CD-5024 SS 5,000 8′ – 10′ (2.4m – 3.7m) 9′ x 10′ (2.7m x 3.0m) 7′ x 8′ (2.1m x 2.4m) 11′ x 12′ (3.4m x 3.7m)
CD-6024 SS 6,000 8′ – 12′ (3.0m – 4.3m) 11′ x 11′ (3.4m x 3.4m) 10′ x 10′ (3.0m x 3.0m) 12′ x 12′ (3.7m x 3.7m)

NOTE: Mounting height should not be less than 6′ (1.8m) if the heater is labeled as UL Listed and 8′ (2.4m) if the heater is labeled as CUL Listed. Indoor or well-protected environments will generally exceed average. Heaters can provide less than average coverage in extremely cold/windy conditions.

GENERAL NOTES

  • INFRATECH QUARTZ TUBE ELECTRIC HEATERS are furnished with multi-position wall/ceiling mount brackets.
  • See sales literature and price list for full listing of models, descriptions, amperages, and voltages. At times, especially when the mounting height might be quite low, an increased number of smaller heaters can help prevent overheating.
  • Heaters up to 15 AMPS can be controlled with a simple INF Input Regulator. This low cost controller, which is actually an infinite switch, gently pulses the heat on and off at regular intervals when not on full power.
  • Dual Element Heaters can be wired with our Duplex/Stack Switch, which enables the ability to turn on and off each element independently, providing for half power/full power capabilities.
  • For ideal comfort heat, the best solution is to heat from two sides rather than from just one side. However, there are times when this is not practical.
  • Coverage areas are approximate dimensions and will vary depending on prevailing and personal comfort levels.
  • Indoor or well-protected environments will generally exceed average (see charts). Heaters can provide less than average coverage in extremely cold/windy conditions.

MAINTENANCE INSTRUCTIONS

  • Before performing any maintenance, power must be disconnected and the heater cool to touch.
  • Heater housing, reflectors, and heating element can be rinsed with a hose or wiped down with isopropyl alcohol, acetone, or glass cleaner. Use a clean, scratch-free rag or paper towel. Any oxidation, surface rust, or discoloration can be removed with a stainless steel cleaner or metal polish on the bare metal surface.
  • Make sure all water, solvents, or cleaners are removed and the heater is dry before reconnecting the power.

TROUBLESHOOTING

LOCATION SUGGESTIONS

Unless heaters are installed over 12′ (3.7m) high, it is generally recommended that all radiant heaters be mounted on an angle to assure that radiant warmth is distributed from the sides rather than straight down on the heads and shoulders of the people being warmed.

LIMITED PRODUCT WARRANTY

Model #:                                                                                Serial #:                                                                            
Date of Purchase:                                                                  Purchased From:                                                                            

Thank you very much for purchasing a INFRATECH Quartz Tube Electric Heater.
We have designed this heater to provide you and your family with many years of great outdoor experiences. Please fill in the Model and Serial number as well as date of purchase in the areas indicated above. Please save this information for future reference. To get the full and safe enjoyment of your electric heater please read your Owner’s Manual carefully and review the proper operating and safety instructions with any family members that may be using the heater.

Manufacturer Warranty:
INFRATECH warrants that this electric heater is designed and manufactured to be free from defects in materials and workmanship for a period of THREE YEARS from the original date of purchase.

Extent of Warranty:
This warranty extends to the selling dealers to the original purchaser at the original site of installation: This warranty becomes valid at the time of purchase and ends either by specified time frame listed above, owner transfer or relocation. In order to activate the warranty we require that you send in the attached warranty registration form. This registration is for our internal use only and will only be used in the event we need to send you important safety related product information. The information will not be sold or used for any marketing related purposes.

Warranty Limitations and Exclusions:
This warranty does not apply to damages resulting from negligence, alteration, misuse, abuse, accident, natural disaster, improper installation or improper operation, unauthorized adjustments or calibrations, dings, dents, scratches, nor damages due to harsh chemicals (i.e. cleaning products improperly applied). Warrantor is not responsible for consequential or incidental damages. Under no circumstances shall INFRATECH or any of its representatives be held liable for injury to any person or damage to any property, however arising.

Important: Please retain original proof of purchase to establish warranty period.

Any implied warranties of merchantability and fitness applicable to the equipment are limited in duration to the period of coverage of this express written warranty. This warranty grants specific legal rights to the purchaser. Other rights, which may vary from state to state, may also apply. Title to the merchandise passes to the consignee upon acceptance by the carrier. After acceptance by the carrier, the merchandise travels at the risk of the purchaser. In the event of freight damage, do not refuse shipment. Advise both the freight agent and the shipper of the damage. Note the details of that damage on the freight bill before any freight charges are paid and file a claim for damages with the freight agent.

Online Warranty Registration
Register your Infratech heater online today and you’ll not only be covered by the most extensive three-year warranty in the industry – you’ll also be automatically enrolled in our Heater Maintenance Program. This means you can enjoy industry-leading customer support and receive free replacement end reflectors when needed, to keep your heating system looking as new as the day it was installed. Register at: infratech-usa.com/warranty

INFRATECH WARRANTY REGISTRATION

Customer Name:                                                                                               Address:
City:                                                                     

State:     Zip: Phone:
E-mail: Model #:
Serial #: Dealer’s Name:
Date Purchased: Dealer’s Address:                                                                

This Warranty Registration Card must be returned within thirty days of purchase to properly activate your warranty. This information is for our internal use only.

15700 South Figueroa Street Gardena, CA 90248
TEL 800-421-9455 or 310-354-1250 FAX 310-523-3674 WWW.INFRATECH-USA.COM

Documents / Resources

INFRATECH COMFORT CDX024SS CD-Series Quartz Tube Electric Infrared Radiant Heater [pdf] User Manual
C-Series, CD-Series, CDX024SS CD-Series Quartz Tube Electric Infrared Radiant Heater, CDX024SS, CD-Series Quartz Tube Electric Infrared Radiant Heater, Infrared Radiant Heater, Radiant Heater, Heater

References

Recent Posts

nordlux VERONA Floor Lamp Instruction Manual

VERONA Floor Lamp 4J[FYNN opb Bulb not 1 included 4 5 2 4 3 1…

19 mins ago

DYNAVIN D8-DF17 Pro 10.1-inch Android Car Radio Instruction Manual

D8-DF17 Pro 10.1-inch Android Car Radio

21 mins ago

WOLFBOX D07 Mirror Dash Cam Instruction Manual

D07 Mirror Dash Cam Mirror Dash Cam D07 Instruction Manual 2 3 4 9 10…

28 mins ago

ICEKING ICE-IK9653W.E Fridge Freezer User Manual

ICE-IK9653W.E Fridge Freezer Fridge Freezer in White If you experience any issues with your product…

44 mins ago

Sprecher Schuh CS7 Standard Control Relays User Manual

CS7 Standard Control Relays Industrial Control Relays Series CS7 - Standard Relay Series CS7 Standard…

46 mins ago

MERCURY KM3KM Ham Radio User Manual

KM3KM Ham Radio USER MANUAL Features Operating Bands 160m ­ 6m (Ham Bands) RF Auto…

47 mins ago