Document

INALTO LOGOINALTO ICC905TB.1 90cm Ceramic CooktopINALTO ICC905TB.1 90cm Ceramic Cooktop PRODUCT

Safety Instructions

IMPORTANT INFORMATION
The following statements you will see in this booklet have these meanings:
WARNING!
Indicating information concerning your personal safety.
CAUTION
Indicating information on how to avoid damaging the appliance or cabinetry.
IMPORTANT
Indicating tips and information about use of the cooktop.
CONDITIONS OF USE
This appliance is intended to be used in domestic environments (i.e. households) and similar applications such as:

  • Staff kitchen areas in shops, offices and other working environments
  • By clients in hotels, motels and other residential type environments
  • Farm houses
  • Bed and breakfast type environments
  • Catering and similar non-retail applications

BEFORE USING YOUR APPLIANCE

  • Before you use the appliance, we recommend that you read through the relevant sections of this manual, which provides the description of your appliance and its functions.
  • To avoid the risks that are always present when you use an appliance, it is important that the appliance is installed correctly and that you read the safety instructions carefully to avoid misuse and hazards.
  • We recommend that you keep this instruction booklet for future reference and pass it on to any future owners.
  • This appliance complies with requirements of Australian Standard AS/NZS 60335.2.6

INSTALLATION
Electrical Shock Hazard

  • Disconnect the appliance from the mains electricity supply before carrying out any work or maintenance on it.
  • Connection to a good earth wiring system is essential and mandatory.
  • Alterations to the domestic wiring system must only be made by a qualified electrician.
  • Failure to follow this advice may result in electrical shock or death.

Cut Hazard

  • Take care – panel edges are sharp.
  • Failure to use caution could result in injury or cuts.

Important safety instructions

  • Read these instructions carefully before installing or using this appliance.
  • No combustible material or products should be placed on this appliance at any time.
  • Please make this information available to the person responsible for installing the appliance as it could reduce your installation costs.
  • In order to avoid a hazard, this appliance must be installed according to these instructions for installation.
  • This appliance is to be properly installed and earthed only by a suitably qualified person.
  • This appliance should be connected to a circuit which incorporates an isolating switch providing full disconnection from the power supply.
  • Failure to install the appliance correctly could invalidate any warranty or liability claims.
  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
  • Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
  • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
  • Warning: If the surface is cracked, switch off the appliance to avoid the possibility of electric shock, for cooktop surfaces of glass-ceramic or similar material which protect live parts
  • Metallic objects such as knives, forks, spoons and lids should not be placed on the cooktop surface since they can get hot
  • A steam cleaner is not to be used.
  • Do not use a steam cleaner to clean your cooktop.
  • The appliance is not intended to be operated by means of an external timer or separate remote-control system.
  • WARNING Danger of fire: do not store items on the cooking surfaces.
  • The cooking process has to be supervised. A short term cooking process has to be supervised continuously.
  • WARNING Unattended cooking on a cooktop with fat or oil can be dangerous and may result in fire. NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.

OPERATION AND MAINTENANCE

Electrical Shock Hazard

  • Do not cook on a broken or cracked cooktop. If the cooktop surface should break or crack, switch the appliance off immediately at the mains power supply (wall switch) and contact a qualified technician.
  • Switch the cooktop off at the wall before cleaning or maintenance.
  • Failure to follow this advice may result in electrical shock or death.

Health Hazard

  • This appliance complies with electromagnetic safety standards.
  • However, persons with cardiac pacemakers or other electrical implants (such as insulin pumps) must consult with their doctor or implant manufacturer before using this appliance to make sure that their implants will not be fected by the electromagnetic field.
  • Failure to follow this advice may result in death.

Cut Hazard

  • The razor-sharp blade of a cooktop scraper is exposed when the safety cover is retracted. Use with extreme care and always store safely and out of reach of children.
  • Failure to use caution could result in injury or cuts.

Hot Surface Hazard

  • During use, accessible parts of this appliance will become hot enough to cause burns.
  • Do not let your body, clothing or any item other than suitable cookware contact the ceramic glass until the surface is cool.
  • Keep children away.
  • Handles of saucepans may be hot to touch.
  • Check saucepan handles do not overhang other cooking zones that are on. Keep handles out of reach of children.
  • Failure to follow this advice could result in burns and scalds.

Important safety instructions

  • Never leave the appliance unattended when in use. Boil over causes smoking and greasy spillovers that may ignite.
  • Never use your appliance as a work or storage surface.
  • Never leave any objects or utensils on the appliance.
  • Do not place or leave any magnetic objects (e.g. credit cards, memory cards) or electronic devices (e.g. computers, MP3 players) near the appliance, as they may be affected by its electromagnetic field.
  • Never use your appliance for warming or heating the room.
  • After use, always turn off the cooking zones and the cooktop as described in this manual (i.e. by using the touch controls). Do not rely on the pan detection feature to turn off the cooking zones when you remove the pans.
  • Do not allow children to play with the appliance or sit, stand, or climb on it.
  • Do not store items of interest to children in cabinets above the appliance. Children climbing on the cooktop could be seriously injured.
  • Do not leave children alone or unattended in the area where the appliance is in use.
  • Children or persons with a disability which limits their ability to use the appliance should have a responsible and competent person to instruct them in its use. The instructor should be satisfied that they can use the appliance without danger to themselves or their surroundings.
  • Do not repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should be done by a qualified technician.
  • Do not place or drop heavy objects on your cooktop.
  • Do not stand on your cooktop.

Important safety instructions (cont.)

  • Do not use pans with jagged edges or drag pans across the ceramic glass surface as this can scratch the glass.
  • Do not use scourers or any other harsh abrasive cleaning agents to clean your cooktop, as these can scratch the ceramic glass.
  • WARNING The appliance and its accessible parts become hot during use.
  • Care should be taken to avoid touching heating elements.
  • Children less than 8 years of age shall be kept away unless continuously supervised

IMPORTANT Check for any damage or marks. If you find the appliance is damaged or marked, you must report it within 7 days if you wish to claim for damage/ marks under the manufacturer’s warranty. This does not affect your statutory rights. A damaged cooktop should never be installed.

INFORMATION ON DISPOSAL FOR USERS

  • Most of the packaging materials are recyclable. Please dispose of these materials through your local recycling depot or by placing them in appropriate collection containers.
  • If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.
  • WARNING! Read the following carefully to avoid damage or injury.
  • Do not allow pots to boil dry, as damage to both pan and cooktop may result.
  • Do not operate the cooktop for an extended period without a pot or pan on the burner.
  • Do not allow large cookware to overhang the cooktop onto adjacent benchtop. This will cause scorching to the benchtop surface.
  • Do not allow cooking pots or pans to intrude into the area which is close to the controls.
  • In the event of faults with the appliance or damage to the glass ceramic (cracks, scratches or splits), the appliance must be switched off and disconnected from the electrical supply, to prevent the possibility of an electric shock.
  • Repairs to the appliance must only be carried out by trained registered service engineers.

CAUTION: Read the following carefully to avoid an electric shock or fire.
It is important to use your cooktop safely. Check these safety points before using your cooktop.

  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge,unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  • Children should be supervised to ensure they do not play with this appliance.
  • During use, this appliance becomes hot. Care should be taken to avoid touching hot surfaces. To avoid burns, young children should be kept away.
  • Do not leave the appliance unattended during operation.
  • This appliance should be used only for normal domestic cooking and frying of food.
  • The appliance must not be used as a work surface or as a storage surface.
  • Additions or modifications to the appliance are not permitted.
  • Do not place or store flammable liquids, highly inflammable materials or fusible objects (e.g. plastic film, plastic, aluminium) on or near the appliance.
  • Keep vents clear of obstructions.
  • In order to avoid a fire, this appliance must be kept clean.
  • Do not spray aerosols in the vicinity of this appliance while it is in operation.
  • Do not place anything, e.g. asbestos mat between pan and trivet as serious damage to the cooktop may occur.
  • Handles should be turned away from the front of the bench to avoid accidents.
  • Do not modify this appliance.
  • Other than the connection point in the terminal block, do not let the electrical supply cord touch the appliance or hot cookware. Ensure electrical supply cord is not tangled.

Your InAlto Cooktop

PRODUCT
LEGENDINALTO ICC905TB.1 90cm Ceramic Cooktop FIG 1

  1. Max. 1800 W zone
  2. Max. 1200 W zone
  3. Max. 1100/ 2000 W zone
  4. Max. 1000/ 2200 W zone
  5. Max. 1200 W zone
  6. Glass plate
  7. Control panel

CONTROL PANEL
LEGENDINALTO ICC905TB.1 90cm Ceramic Cooktop FIG 2

  1. Heating zone selection controls
  2. Power/Timer slider touch control
  3. Dual zone control
  4. Lock control
  5. ON/OFF control
  6. Timer control

Before First Use

  • Before using this appliance read this manual, taking special note of the ‘Safety Instructions’ section
    IMPORTANT! You should clean the ceramic cooktop surface (refer to the ‘Cleaning and Maintenance’ section)..
  • Before using the appliance, ensure that all packing materials are removed from the appliance.
  • You should switch on one cooking zone at a time, for 5 minutes at the maximum setting. This will help to eliminate any new smell that exists and evaporate any humidity that has formed on the heating elements during transit.
  • Do not burn off more than one zone at once.
  • You must place a saucepan filled half full with cold water on each cooking zone as you burn it off.

INSTALLATION

  • In order to avoid any potential hazard, the installation instructions in this booklet, and any labels on the appliance must be followed.
  • Installation may only be carried out by a qualified electrician. The minimum distances to other appliances and units are to be observed.
  • The laws, ordinances, directives and standards in force in the country of use are to be followed (safety regulations, proper recycling in accordance with the regulations, etc.)
  • Ensure that all specified vents, openings and air spaces are not blocked.
  • Anti-shock protection must be provided by the installation, for example drawers may only be installed with a protective floor directly underneath the appliance.
  • The cut surfaces of the worktop are to be protected against moisture using a suitable sealant. The sealant seals the appliance to the work top with no gap. Do not use silicon sealant between the appliance and the work top.
  • Avoid installing the appliance next to doors and under windows. Otherwise hot cookware may be knocked off the cooktop when doors and windows are opened.
  • Where the appliance is built into a benchtop, the benchtop material must be capable of withstanding 85°C.

SERVICING

  • Servicing MUST only be carried out by authorised personnel.
  • To maintain safe operation, it is recommended that the product be inspected every five years by an authorised service person.
  • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

WARNING! Never install a cooktop that has been damaged. Please contact our Customer Care team for further assistance.
CLEANING

  • Always ensure the appliance is turned off before cleaning and allowed to cool.
  • Do not use steam cleaners as this may cause moisture build up on electrical components.
  • Always clean the appliance immediately after any food spillage.
  • Refer to the ‘Cleaning and Maintenance’ section of this user manual for instructions on cleaning and maintaining your ceramic glass cooktop.

Using Your Cooktop

GENERAL USE INSTRUCTIONS

  • Do not use cookware with jagged edges or a curved base.INALTO ICC905TB.1 90cm Ceramic Cooktop FIG 333
  • Make sure that the base of your pan is smooth, sits flat against the glass, and is the same size as the cooking zone. Always centre your pan on the cooking zone.INALTO ICC905TB.1 90cm Ceramic Cooktop FIG 4
  • Always lift pans off the ceramic cooktop – do not slide, or they may scratch the glass.INALTO ICC905TB.1 90cm Ceramic Cooktop FIG 5

Operation Instructions

TOUCH CONTROLS

  • All operations are performed by means of the touch controls that can be found on the control panel at the front

USING THE TOUCH CONTROLS

  • The controls respond to touch, so you don’t need to apply any pressure.
  • Use the ball of your finger, not its tip.
  • You will hear a beep each time a touch is registered.
    Make sure the controls are always clean, dry, and that there is no object (e.g. a utensil or a cloth) covering them. Even a thin film of water may make the controls difficult to operate.

TO START COOKING

IMPORTANT! Do not use cookware with jagged edges or a curved base

  • After powering on, the buzzer beeps once, all the indicators light up for 1 second then go out, indicating that the ceramic cooktop has entered the state of standby mode..
    1. Touch the ON/OFF control all the indicatorsshow “-”.
    2. Place a suitable pan on the cooking zone that you wish to use.
      Make sure the bottom of the pan and the surface of the cooking zone are clean and dry.
    3. Touch the heating zone selection control of your desired zone, an indicator next to the key will flash
    4. Adjust heat setting by touching the slider control.
  • If you don’t choose a heat setting within 1 minute, the ceramic cooktop will automatically switch off. You will need to start again at step 1
  • You can modify the heat setting at any time during cooking.
  • You can modify the power level from 0 to 9 by the slide control.INALTO ICC905TB.1 90cm Ceramic Cooktop FIG 6

WHEN YOU HAVE FINISHED COOKING

  1. Touching the heating zone selection control that you wish to switch off.
  2. Turn the cooking zone off by touching the slider to ” l ”. Make sure the display shows ”0”
  3. Turn the whole cooktop off by touching the ON/OFF control.
    • After a zone is switched off, the corresponding cooking zone will show an “H” in the control panel. This means that the temperature of the zone still high enough to cause injury.
    • The residual heat indicator will go out when the surface has cooled down to a safe temperature.
    • The residual heat also can be used as an energy saving function if you want to heat further pans,use the hotplate that is still hot.

IMPORTANT! The residual heat indicator will disappear if the mains supply to the product is cut.
WARNING! It is still possible to burn yourself on a cooktop zone, even when the residual heat indicator has gone off. Always use caution when using the cooktop.

LOCKING THE CONTROLS

  • • You can lock the controls to prevent unintended use (for example children accidentally turning the cooking zones on).
    • When the controls are locked, all the controls except the ON/OFF control are disabled.

To lock the controls

Touch the lock symbol. The timer indicator will show “Lo“.

To unlock the controls

  • Make sure the ceramic cooktop is turned on.
  • Touch and hold the lock symbol for a few seconds.
  • The cooktop will unlock and you can now start using your ceramic hob.

WARNING! When the cooktop is in the lock mode, all the controls are disable except the ON/OFF, you can always turn the ceramic cooktop off with the ON/OFF control in an emergency, but you shall unlock the cooktop first in the next operation.

Operation Instructions (Continued)

AUTOMATIC SHUT-OFF
Your ceramic cooktop features a safety feature for automatic power-off occurring whenever you forget to switch off a cooking zone.
The default shutdown times are shown in the table below:INALTO ICC905TB.1 90cm Ceramic Cooktop FIG 7

Setting a timer for more than one zone

  • Use the same steps above to set timers against multiple zones.
  • When you set the time for several cooking zones simultaneously, a red dot will illuminate next to the power level indicator for each relevant zone.
  • When setting or adjusting a timer against a zone, the red dot indicating the zone being adjusted, will flash intermittently.INALTO ICC905TB.1 90cm Ceramic Cooktop FIG 8
  • If more than one heating zone uses this function, the timer indicator will show the lowest time. (e.g. zone #1 remaining time of 5 minutes, zone #2 remaining time of 15 minutes, the timer indicator shows “5”.)
  • Once the countdown timer expires, the corresponding zone will switch off. Then it will show the new min. timer and the dot of corresponding zone will flash.INALTO ICC905TB.1 90cm Ceramic Cooktop FIG 9
  • If you want to change the time after the timer is set, you have to start from step 1.INALTO ICC905TB.1 90cm Ceramic Cooktop FIG 10

Installation Instructions

WARNING This user manual must be read! The laws, ordinances, directives and standards in force in the country of use are to be followed (safety regulations, proper recycling in accordance with the regulations, etc.)
IMPORTANT!
Installation may only be carried out by a qualified electrician. The minimum distances to other appliances and units are to be observed.
Anti-shock protection must be provided by the installation, for example drawers may only be installed with a protective floor directly underneath the appliance.
The cut surfaces of the worktop are to be protected against moisture using a suitable sealant. The sealant seals the appliance to the work top with no gap. Do not use silicon sealant between the appliance and the work top.
Avoid installing the appliance next to doors and under windows. Otherwise hot cookware may be knocked off the rings when doors and windows are opened.
WARNING! Risk of injury from electrical current.

  • The electrical mains terminal is live.
  • Make electrical mains terminal free of voltage.
  • Follow connection schematic.
  • Observe electrical safety rules.
  • Ensure anti-shock protection by installing correctly.
  • The appliance must be connected to the electrical supply by a qualified electrician.
  • Loose and inappropriate plug and socket connections can make the terminal overheat.
  • Have the clamping connections correctly installed by a qualified electrician.
  • Use strain relief clamp on cable.
  • WARNING! The surface temperature exceeds 90°C. To avoid a hazard, under bench access must be restricted.
  • Be aware that the glue that join the plastic or wooden material to the furniture, has to resist to temperatures of up to 150°C, to prevent panelling from unsticking
  • The rear wall, adjacent and surrounding surfaces must therefore be able to withstand a temperature of 90 °C.
  • WARNING! Once connected to the mains supply check that all cooking zones are ready for use by briefly switching each on in turn at the maximum setting.
  • A duplicate rating label is supplied with this unit. For easy identification of this unit after installation, stick it to a readily available surface adjacent to the cooktop.

Applying the seal

  • Clean the worktop around the cutout area.
  • Stick the single-sided adhesive sealing tape provided on the underside of the cooktop around the outside edge ensuring that it is not stretched. The two ends of the tape should join in the middle of one side. After trimming the tape (allow it to overlap by 2-3 mm), press the two ends together.

INSTALLATION

Cut out the work surface according to the sizes shown in the drawing. For the purpose of installation and use, a minimum of 5 cm space shall be preserved around the hole. Be sure the thickness of the work surtace is at least 50mm. Please select heat-resistant and insulated work surface material (Wood and similar fibrous or hygroscopic material shall not be used as work surface material unless mpregnated) to avoid the electrical shock and larger deformation caused by the heat radiation from the hotplate.INALTO ICC905TB.1 90cm Ceramic Cooktop FIG 11

Note: The safety distance between the sides of the cooktop and the inner surfaces of the worktop should be at least 3mm.

Installation Instructions (Continued)

CLEARANCES
Under any circumstances, make sure the ceramic cooktop is well ventilated and the air inlet and outlet are not blocked. Ensure the ceramic cooktop is in good working state as shown below.INALTO ICC905TB.1 90cm Ceramic Cooktop FIG 12

  1. Refer to rangehood manual*
  2. 50mm minimum
  3. 50mm minimum
  4. Air Inlet
  5. Air Outlet (5mm

Please refer to your rangehood’s user manual for minimum clearances from the top of the cooktop surface to your rangehood.

WARNING Ensuring Adequate VentilationINALTO ICC905TB.1 90cm Ceramic Cooktop FIG 14
Make sure the ceramic cooktop is well ventilated and that air inlet and outlet are not blocked. In order to avoid accidental touch with the overheating bottom of the hob, or getting an unexpected electric shock during working,
it is necessary to put a wooden insert, fixed by screws, at a minimumn distance of 50mm from the bottom of the hob. Follow the requirements to the right.

LOCATING THE FIXING BRACKETS
The unit should be placed on a stable, smooth surface (use the packaging or a towel). Do not apply force onto the controls protruding from the hob.
Fix the cooktopon the work surface by screw four brackets on the bottom of cooktop(see picture) after installation.
Adjust the bracket position to suit for different work surface’s thicknesses.INALTO ICC905TB.1 90cm Ceramic Cooktop FIG 15

Under any circumstances, the brackets cannot touch with the inner surfaces of the worktop after installation (see picture).
caution

  1. The ceramic cooktop must be installed by qualified personnel or technicians. We have protessionals at your service. Please never conduct the operation by yourself.
  2. he ceramic cooktop shall not be mounted to cooling equipment, dishwashers and rotary dryers.
  3. The ceramic cooktop shall be installed such that better heat radiation can be ensured to enhance its reliability.
  4. he wall and induced heating zone above the work surtace shall witnstand hedt. .lo avoid any damage, the sandwich layer and adhesive must be resistant to heat.
  5. A steam cleaner is not to be used.

ELECTRICAL CONNECTION

IMPORTANT The cooktop must NOT be connected to the mains supply by means of a 10A or 15A plug and socket.
The power supply should be connected in compliance with the relevant standard, or a single-pole circuit breaker. The method of connection is shown in the figures below.

Wiring DiagramINALTO ICC905TB.1 90cm Ceramic Cooktop FIG 16

Notes: Ihe bottom surtace and the power cord of the cooktop are not accessible atfter installation.

  1. If the cable is damaged or needs replacing, this should be done by an after-sales technician using the proper tools, so as to avoid any accidents.
  2. If the appliance is being connected directly to the mains supply, an omnipolar circuit breaker must be installed with a minimum gap or 3mm between the contacts.
  3. The installer must ensure that the correct electrical connection has been made and that it complies with safety regulations.
  4. The cable must not be bent or compressed.
  5. The cable must be checked regularly and only replaced by a properly qualifñed person.
  6. The installer must to use the Ho5GG-F power cord.

Cleaning & Maintenance

By ensuring proper cleaning and maintenance of your InAlto cooktop, you can ensure that it will have a long and fault free operation.

GENERAL CLEANING INSTRUCTIONS
WARNING Do not start cleaning the cooktop until it has completely cooled.
WARNING Sharp objects and abrasive cleaning materials will damage the appliance. Clean with water and washing up liquid.

  • Any residues that are left on the cooktop surface from cleaning agents will damage it. You should remove any residues with warm water mixed with a little washing up liquid.
  • Abrasive cleaners or sharp objects will damage the cooktop surface; you should clean it using warm water mixed with a little washing up liquid.
  • Although it is easier to clean some deposits whilst the cooktop surface is still warm, you should take care not to burn yourself if cleaning the cooktop surface when it is still warm.

After each use:

  • Wipe the cooktop over with a damp cloth.
  • Dry the cooktop by rubbing the surface with a clean cloth.

TYPES OF SPILLS
Everyday soiling on glass (fingerprints, marks, stains left by food or non-sugary spillovers on the glass)

  1. Switch the power to the cooktop off.
  2. Apply a cooktop cleaner while the glass is still warm (but not hot!)
  3. Rinse and wipe dry with a clean cloth or paper towel.
  4. Switch the power to the cooktop back on.
    • When the power to the cooktop is switched off, there will be no ‘hot surface’ indication but the cooking zone may still be hot! Take extreme care.
    • Heavy-duty scourers, some nylon scourers and harsh/abrasive cleaning agents may scratch the glass. Always read the label to check if your cleaner or scourer is suitable.
    • Never leave cleaning residue on the cooktop: the glass may become stained.

Boil overs, melts, and hot sugary spills on the glass Remove these immediately with a fish slice, palette knife or razor blade scraper suitable for ceramic glass cooktops, but beware of hot cooking zone surfaces:

  1. Switch the power to the cooktop off at the wall.
  2. Hold the blade or utensil at a 30° angle and scrape the soiling or spill to a cool area of the cooktop.
  3. Clean the soiling or spill up with a dish cloth or paper towel.
  4. Follow steps 2 to 4 for ‘Everyday soiling on glass’ above.
    • Remove stains left by melts and sugary food or spillovers as soon as possible. If left to cool on the glass, they may be difficult to remove or even permanently damage the glass surface.
    • Cut hazard: when the safety cove is retracted, the blade in a scraper is razor-sharp. Use with extreme care and always store safely and out of reach of children.

Spillovers on the touch controls

  1. Switch the power to the cooktop off.
  2. Soak up the spill
  3. Wipe the touch control area with a clean damp sponge or cloth.
  4. Wipe the area completely dry with a paper towel.
  5. Switch the power to the cooktop back on.
    • The cooktop may beep and turn itself off, and the touch controls may not function while there is liquid on them. Make sure you wipe the touch control area dry before turning the cooktop back on.

Cleaning & Maintenance (Continued)

USING A SPECIALIST CERAMIC COOKTOP CLEANER

  • It is possible to purchase a specialist ceramic cooktop cleaner/conditioner.
  • You should follow the instructions given by the manufacturer of the cleaner and ensure that it is suitable for use on your appliance.
  • NOTE Scratches or dark stains on the glass ceramic that cannot be removed will not affect the functioning of the appliance.
  • IMPORTANT Residues from cleaning agents will damage the appliance. Remove residues with water and washing up liquid.

Troubleshooting

Some minor faults can be fixed by referring to the instructions given below. Please do not disassemble the unit by yourself to avoid any dangers and damages to the ceramic cooktop. Instead contact our customer care team on 1300 11 4357 or visit our self help portal online at www.support.residentiagroup.com.au.

Problem Possible Cause Remedy
The cooking zones are not functioning or will not switch on •    The mains electrical connection may be incorrect or lose.

•    Child lock is switched on.

•    The appliance was left inactive for too long after switching on and has since powered off.

•    Have your installer check their connection. Check the mains fuse box to ensure a fuse has not been tripped or blown.

•    Check the Child lock is off.

•    Try powering the cooktop on once more.

A humming sound is heard when a cooking zone is selected This is normal for all ceramic cooktops. The sound should disappear when the zone has heated up.
Pitting of ceramic glass surface. Spill-overs of liquid with high sugar content. These types of spills must be removed immediately with a special scraper for the glass. If not permanent damage to the cooktop

glass can occur which is not covered

under warranty.

Red rings, Limescale, water rings, shiny metallic or other

discolouration, scratches, shadows, bubbles, or other marks or stains have appeared on the ceramic glass surface

Cooktop surface has not been cleaned correctly. Cleaning/ maintenance of the cooktop surface is not covered under warranty. If a service call is placed to clean the cooktop surface, you will be charged for the visit. Use a ceramic glass cleaner such as Cerapol available from most supermarkets or for purchase from our Customer Care team.
The residual heat indicator is not displaying anything. The cooking zone was only on for a short time and is therefore not hot. If the cooking zone is hot and has been in operation for at least 30 seconds and still no residual heat indicator active, call the Customer Service Department.
The touch controls are unresponsive. The controls are locked. Unlock the controls. See section ‘Using your ceramic cooktop’ for instructions.
The touch controls are difficult to operate. There may be a slight film of water over the controls or you may be using the tip of your finger when touching the controls. Make sure the touch control area is dry and use the ball of your finger when touching the controls.

Technical Specifications

MODEL ICC905TB.1
RATED VOLTAGE 220-240V~ 50 or 60Hz
INSTALLED ELECTRIC POWER 7600-9200W
PRODUCT SIZE (W x D x H mm) 900 × 520 × 55mm
BUILT IN DIMENSIONS (A x B mm) 875 × 495mm

Warranty Information

AUSTRALIAN WARRANTY TERMS & CONDITIONS COOKING APPLIANCES
This document sets out the terms and conditions
of the product warranties for Residentia Group Appliances. It is an important document. Please keep it with your proof of purchase documents in a safe place for future reference should you require service for your Appliance.

IN THIS WARRANTY

  1. ‘acceptable quality’ as referred to in clause 10 of this warranty has the same meaning referred to in the ACL;
  2. ‘ACL’ means Trade Practices Amendment (Australian Consumer Law) Act (No.2) 2010;
  3. ‘Appliance’ means any Residentia Group product purchased by you accompanied by this document;
  4. ‘ASR’ means Residentia Group authorised service representative;
  5. ‘Residentia Group’ means Residentia Group Pty Ltd of 165 Barkly Avenue Burnley VIC, ACN 600 546 656 in respect of Appliances purchased in Australia;
  6. ‘major failure’ as referred to in clause 10 of this warranty has the same meaning referred to
    in the ACL and includes a situation when an Appliance cannot be repaired or it is uneconomic for Residentia Group, at its discretion, to repair an Appliance during the Warranty Period;
  7. ‘Warranty Period’ means:
  8. where the Appliance is used for personal, domestic or household use (i.e. normal single family use) as set out in the instruction manual, the Appliance is warranted against manufacturing defects for 24 months (or 36 months where a valid extended warranty registration has occurred), following the date of original purchase of the Appliance;
  9. ‘you’ means the purchaser of the Appliance not having purchased the Appliance for re-sale, and ‘your’ has a corresponding meaning.
    1. This warranty only applies to Appliances purchased and used in Australia and is in addition to (and does not exclude, restrict, or modify in any way) any non-excludable statutory warranties in Australia.
    2. During the Warranty Period Residentia Group or its ASR will, at no extra charge if your Appliance is readily accessible for service, without special equipment and subject to these terms and conditions, repair or replace any parts which it considers to be defective. Residentia Group or its ASR may use remanufactured parts to repair your Appliance. You agree that any replaced Appliances or parts become the property of Residentia Group. This warranty does not apply to light globes, batteries, filters or similar perishable parts.
    3. Parts and Appliances not supplied by Residentia Group are not covered by this warranty.
    4. You will bear the cost of transportation, travel and delivery of the Appliance to and from Residentia Group or its ASR. If you reside outside of the service area, you will bear the cost of:
      1. travel of an authorised representative;
      2. transportation and delivery of the Appliance to and from Residentia Group or its ASR, in all instances, unless the Appliance is transported by Residentia Group or its ASR, the Appliance is transported at the owner’s cost and risk while in transit to and from Residentia Group or its ASR.
    5. Proof of purchase is required before you can make a claim under this warranty.
    6. You may not make a claim under this warranty unless the defect claimed is due to faulty or defective parts or workmanship. Residentia Group is not liable in the following situations (which are not exhaustive):(a) the Appliance is damaged by:
      1. accident
      2. misuse or abuse, including failure to properly maintain or service
      3. normal wear and tear
      4. power surges, electrical storm damage or incorrect power supply
      5. incomplete or improper installation
      6. incorrect, improper or inappropriate operation
      7. insect or vermin infestation
      8. failure to comply with any additional instructions supplied with the Appliance;
      9. the Appliance is modified without authority from Residentia Group in writing;
      10. the Appliance’s serial number or warranty seal has been removed or defaced;
      11. the Appliance was serviced or repaired by anyone other than Residentia Group, an authorised repairer or ASR.
    7. This warranty, the contract to which it relates and the relationship between you and Residentia Group are governed by the law applicable where the Appliance was purchased.
    8. To the extent permitted by law, Residentia Group excludes all warranties and liabilities (other than as contained in this document) including liability for any loss or damage whether direct or indirect arising from your purchase, use or non use of the Appliance.
    9. For Appliances and services provided by Residentia Group in Australia, the Appliances come with a guarantee by Residentia Group that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the Appliance repaired or  replaced if the Appliance fails to be of acceptable quality and the failure does not amount to a major failure. The benefits to you given by this warranty are in addition to your other rights and remedies under a law in relation to the Appliances or services to which the warranty relates.
    10. At all times during the Warranty Period, Residentia Group shall, at its discretion, determine whether repair, replacement or refund will apply if an Appliance has a valid warranty claim applicable to it.
    11. Missing parts are not covered by warranty. Residentia Group reserves the right to assess each request for missing parts in a case by case basis. Any parts that are not reported missing in the first week after purchase will not provide free of charge.
    12. To enquire about claiming under this warranty, please follow these steps:
      1. carefully check the operating instructions, user manual and the terms of this warranty;
      2. have the model and serial number of the Appliance available;
      3. have the proof of purchase (e.g. an invoice) available;
      4. telephone the numbers shown below.
    13. You accept that if you make a warranty claim, Residentia Group and its ASR may exchange information in relation to you to enable Residentia Group to meet its obligations under this warranty.

IMPORTANT
Before calling for service, please ensure that the steps in point 13 have been followed.

Telephone contact Service
Please call 1300 11 HELP (4357)

The Australian Consumer Law requires the inclusion of the following statement with this warranty:
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Documents / Resources

INALTO ICC905TB.1 90cm Ceramic Cooktop [pdf] User Manual
ICC905TB.1, 90cm Ceramic Cooktop, Ceramic Cooktop, ICC905TB.1, Cooktop

References

Leave a comment

Your email address will not be published.