ILIVE LOGO

iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer

iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer

Important Safety Instructions 

  • Read these instructions.
  • Keep these instructions..
  •  Head all Warnings.
  •  Follow all instructions.
  •  Do not use this apparatus near water.
  •  Clean only with a dry cloth.
  • Do not block any ven1ilatlon openings. install In accordance with the manufacturer’ instructions.
  • Do not install near any heat sources such as radiators,  heat regulators, or other apparatus (Including amplifier) that produce heat.

FCC Warnings

Warning: Changes or modification, to 1hu unit not c:xpn,o&ly approved by the party responsible for compliance could void the user’ authority to open the equipment.
NOTE: This equipment bas been teo1l>d and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Thu equipment guarantee, uses, and radiate radio frequency and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee !hot interference will not occur in a particular installation. if this equipment do harmful interference to radio or television reception, which may be determined by turning the equipment off and on, the user is encouraged to try to  the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between receiver and equipment
  • Connect the equipment Into the outlet on a difficult different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician.

Setup

Features & Specifications

  • • 4.5″length
  • Supports Bluetooth s 5.0  range 60 ft.
  • 4.1 channel stereo sound
  •  Digital volume control
  • Full-function remote
  • Optical audio input
  • Auxin{3Sm m audio input)
  • HDMI Arc input

Includes 

  • Remote control with 2 AAA b batteries
  • Optical audio cable
  • 2 AC/DC power  adapter for sound bar and subwoofer.
  • 2 USB-C charging cables
  • Wall-mount hardware and instructions

Power
Plug the power adapters i subwoofer into their respective DC Inputs on the back of the units and standard wall outlet.

iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer FIG 1Remote Battery

Remote control: requires 2 AAA batteries (included).

iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer FIG 2

Assembling the Satellite Speakers 

  1. Power ON the main unit and satellite speakers.
  2. To attach the two satellite speakers, align the end of the main unit with the satellite speaker.
  3. Please make sure each satellite speaker is correctly aligned with the sound bar and gently push into place.
  4. Once pushed into place, rotate the speaker clock wise (right satellite) rotate the speaker counter-clockwise  (left satellite) until locked in.
  5. Please make sure the fully assembled unit is connected to your device. Once connected, audio will now be  heard from the main unit and both satellite speakers. You are now able to remove the speakers using the above steps In reverse.

iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer FIG 3iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer FIG 4

Orientation

Rear View

iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer FIG 6 Front View  iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer FIG 5 Source Mode Indicator LED 

iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer FIG 15

Speaker Controls {Top)

Power/Source.

  • Press to power the unit ON.
  • Press and hold to power the unit OFF. Press to switch audio source

Volume

  • Press to adjust volume.

Pair

  • Press to manually begin Bluetooth pairing (BLUETOOTH MODE). Press and hold for 10 seconds to connect/disconnect satellite speakers to main unit.

iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer FIG 7

Subwoofer

Connecting the Wireless Subwoofer 

  1. Power ON the subwoofer while the sound bar Is ON. The subwoofer will now automatically begin connecting to the sound bar.
  2. When the subwoofer has connected to the sound bar the Connect LED Indicator will turn solid red. When audio is played through any source, the speaker will automatically use the connected subwoofer.
  3. If the connection has failed or is lost, the indicator will tum off. Power OFF the subwoofer and power it ON again to try reconnecting.

iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer FIG 8

NOTE: To reduce unwanted vibration, try place the subwoofer on a solid or padded surface, such as the floor or carpet.

Remote

Functions & Controls 

iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer FIG 9

Connecting Devices

Initial Bluetooth Connection and Playing Audio

  1. When first powered ON the unit defaults to Bluetooth mode. A voice will say, “Bluetooth: and the LED indicator will begin flashing blue. When pairing, remain within 3 feet of the Bluetooth device.
  2. Using the controls on your Bluetooth device, select ITISW421 In the Bluetooth Settings Menu to pair. If need be, refer to the user’s manual for your specific device for more information.
  3. When successfully paired, a voice will announce, “Bluetooth is connected,” and the LED indicator will turn solid blue. Audio from the connected Bluetooth device will now be heard through the speaker.
  4.  Use the controls on the connected Bluetooth device to select and play audio. Use the speaker controls or the connected Bluetooth device to play, pause, and adjust the volume level.
  5. After Initial pairing, anytime the speaker powers ON it will automatically connect to the last Bluetooth device used.
    Note:  If your device should become unpaired or you find It Is unable to connect, press the Play button remote, or Pair button (sound bar) to enter to Pairing Mode. A voice will announce, “Bluetooth is connecting,” and you can connect to the speaker manually.Note: This sound bar has a last-function-used memory; it will resume using the lost mode before it was turned OFF after It Is turned ON again.

Troubleshooting

If the sound bar should become unpaired or will not connect normally, follow these steps in your device’s Bluetooth Settings Menu.

  • Delete the sound bar (“Forget this Device”).
  • Turn Bluetooth OFF, then ON again, and repeat the initial Bluetooth Connection steps.

Auxin
Requires a 3.Smm audio cable (not Included).

  1. Connect a 3.Smm audio cable to the Aux In on the unit and the audio output/headphone Jack on an audio device.
  2. Power ON the sound bar and press Source on the sound bar or Aux on the remote to select Aux In Mode. A voice will announce the source mode and the indicator will turn green.
  3. Use the controls on the connected device to select and play audio. Be sure the volume on your connected device is audible when you begin playing.

iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer FIG 10HDMI (Arc)

HDMI offers superior sound and picture quality when compared to other AV connection types, and Is the easiest way to connect your media devices to the sound bar.
Use the H DMI with Audio Return Channel (ARC) to connect to a compatible audio device with a standard HDMI cable, no stereo or optical audio cables will be needed. Note: ARC may not support surround sound (5.1) or other audio with more than two channels (2.0).

  1. Requires a device that supports HDMI and a HDMI cable (not Included).
  2. Connect the device’s H DMI output to an HDMI Input on the sound bar.
  3. Press the Source button on the sound bar or the HDMT button on the remote to select HDMI mode.

iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer FIG 11

Optical Input
Requires an audio source with an Optical Audio Output and a Digital Optical Audio Cable (included).

  1. Using a Digital Optical Audio cable, connect the Optical Input on the sound bar to the Optical Output on your audio source {TV, amplifier, etc.).
  2. Power ON the sound bar and press Optical on the remote or Source on the sound bar to select Optical Mode. A voice will announce the source mode and the indicator will turn orange.
  3. On the connected audio source (TV, amplifier, etc.), be sure the audio settings are set to PCM or Optical Audio.
  4. Audio played through the connected audio source {TV, amplifier, etc.) should now be heard through the speaker.

important tips for optical audio: 

  • Use the correct optical audio cable and make sure that it is firmly seated in both source and sound bar sockets.
    Optical audio output is activated from the audio source (a red light should be visible from the optical socket). It may be labeled SPDIF In the settings menu of the source.
    The optical output source should be set to output PCM and not Dolby Digital

iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer FIG 12

Wall Mount Bracket Installation

iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer FIG 13iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer FIG 14

Company Information

Website: www.iliveElectronics.com
Email Support: [email protected]
Email Puts: [email protected]
Phone Support: 1-888-999-4215

Warranty
For Warranty Information and the most up-to-date version of this User’s Guide, go to: www.lLlveElectronlcs.com

FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.
    Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Documents / Resources

iLIVE ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer [pdf] User Guide
SR418, ZJP-SR418, ZJPSR418, ITBSW421 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer, ITBSW421, 45 Inch HD Sound Bar with Satellite Speakers and Wireless Subwoofer

Leave a comment

Your email address will not be published.