Plexineon Suspended Dynamic Color
Installation Guide
Plexineon Straight Run Fixture
REV0.1
10252022
Plexineon Suspended Dynamic Color
Installation Instructions – Plexineon Suspended Dynamic Color
Models: Plexineon Suspended Mount Dynamic Color and Plexineon Rings Suspended Mount Dynamic Color Please read all instructions prior to installation and keep for future reference!
- PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
- USE ONLY WITH CLASS 2 POWER UNIT
- 24 VOLTS DC
- SUITABLE FOR WET LOCATIONS
- SUSPENDED MOUNT ONLY
Plexineon Ring Surface Mount
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Models: Plexineon Suspended Mount Dynamic Color and Plexineon Rings Suspended Mount Dynamic Color
Please read all instructions prior to installation and keep for future reference!
- PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
- USE ONLY WITH CLASS 2 POWER UNIT
- 24 VOLTS DC
- SUITABLE FOR WET LOCATIONS
- SUSPENDED MOUNT ONLY
NOTE: Prior to installation all 24VDC wires must be present within 72” of the installation. Refer to the power supply installation instruction for additional information.
NOTE: More than one person is recommended for this installation.
1.1 Screw mounting clip to stand off hub.
1.2 Fix the plexineon fixture into installed mounting clips. See step A for clipping instructions. Make sure mounting clips are certain distance apart.
NOTE: Standard Clips and Decorative Clips have different required spacing.
Install Fixtures into Mounting Clips
A.1 Make an U shape with mounting clip installation tool, insert two edges into mounting clip. Place plexineon fixture insde the shape. Then push the fixture into clip.
A.2 Remove the tool. Make sure mounting clip is clipped right on the grip. 
NOTE: Prior to installation all 24VDC wires must be present in junction box. Refer to the power supply installation instruction for additional information.
2.1 Align one standoff hub to the junction box and mark the other hubs’ location to the ceiling.
3.1 Slide power cord end through strain relief, canopy, and cross bar.
Peel back power cord to expose wires.Connect power supply wires to fixture wires. Waterproof wire nuts recommended in this step.
NOTE: Prior to wiring the desired fixture height must be determind to cut off any un-necessary wire.
4.1 Insert wire nut and extra wire into junction box. Slide weld stud into the center hole of cross bar. Screw cross bar into junction box holes or the ceiling.
4.2 Slide canopy up to the cross bar and secure by tightening the thumb nut to weld stud.
5.1 Screw cap to threaded post with aircraft cable.
5.2 Fix the aircraft cable into thumbnut, secure by tightening by hand.
6.1 Install the rest of other canopies by similar method.
6.2 If necessary, make any final adjustment to power cord using o-ring.
RGB&RGBW WIRING DIAGRAM
WIRING DIAGRAM
SR-DMX-SPI
Smart Pixel LineLED Decoder
NOTE: Please make sure that power is turned off before wiring. Also, ensure that the correct powersupply (voltage and wattage) is used to power the LED strips connected to the decoder. Follow illustrated wiring diagram. Use screwdriver to open and close connection slots.
NOTE: When connecting two or more LED strip lights or light fixtures, always make sure the signal direction arrows are pointing to same direction
The signal direction arrow should appear on label of each section of LED fixture.
OPERATING GUIDE
SR-DMX-SPI
Smart Pixel LineLED Decoder
There are three buttons on the decoder
After operation, if no action was taken within 30s, the button lock, and backlight of the screen will turn off.
- Long press M button for 5s to unlock the buttons, and the backlight will turn on.
- Long press M button for 5s to switch between test mode and decode mode after unlocked.
During test mode, the first line of LCD will show: TEST MODE. Use test mode to verify RGBW Pixel functionality.
Duirng decoder mode, the first line of LCD shows: DECODER MODE. Use decoder mode when connecting to a Controller and for final installation and customization.
The second line of the LCD Display shows the current setting and value. Note: 1 Pixel = 1 Cut Increment MODE TABLE
| SETTING | LCD DISPLAY | VALUE RANGE | DESCRIPTION |
| Built-in Programs | hATENDIEsAX: | 1-26 | See Program Table below |
| Program Speed | TEST MODE RUN SPEED: | 0-7 | 0: fast, 7: slow |
| DMX Address | DECODER MODE DMX ADDRESS: | 1-512 | Address of the starting point/Pixel of a program |
| DMX Signal RGB | DEE)C01:11RBAOSE MX | RGB, BGR, etc. | N/A |
| Pixel Quantity | DECODER MODE PIXEL QTY: | 1-170(RGB), 1-128 (RGBW) | Number of Pixels to follow a program |
| IC TYPE | DECODER MODE IC TYPE: | 2903, 8903, 2904, 8904 | 2903: N/A, 2904: for RUM, 8903: N/A, 8904: N/A |
| Color | DECODER MODE COLOR: | MONO, DUAL, RGB, RGBW | MONO: N/A, DUAL: N/A, RGB: N/A, RGBW: for RGBW |
| Pixel Merging / Pixel Size | DECODER MODE PIXEL MERGE: | 1-100 | Number of Pixels to merge together |
| RGB Sequence | DECODER MODE LED RGB SEQ: | RGBW, BGRW etc. | Sequence of RUM, 24 possible combinations |
| Integral Control | DECODER MODE ALL CONTROL: | YES, NO | Yes: Merge all Pixels No: Maintain individual Pixels or Merged Pixels |
| Reverse Control | DECODER MODE REV-CONTROL: | YES, NO | Reverse program order |
| Overall Brightness | DECODER MODE BRIGHTNESS: | 1-100 | 1: dimmest setting 100: brightest setting |
NOTE: When connected to a controller, DMX512 Signal Decoder will stay in “Decoder Mode”.
NOTE: The actual maximum control pixels of the controller are 1360 (2903) ,1024 (2904).
Please set the pixel and pixel combination value according to the actual situation, and DO NOT exceed the maximum.
NOTE: For Program Table
Change: no fading/dimming between color changes
Fade: fade/dim between color changes
Chase: change pixel by pixel
Chase with Trail: change pixel by pixel with fading between
PROGRAM TABLE
| PROGRAM NO. | PROGRAM DESCRIPTION |
| 1 | Solid color: Red |
| 2 | Solid color: Green |
| 3 | Solid color: Blue |
| 4 | Solid color: Yellow |
| 5 | Solid color: Purple |
| 6 | Solid color: Cyan |
| 7 | Solid color: White |
| 8 | RGB change |
| 9 | Full color change |
| 10 | RGB fading |
| 11 | Full color fading |
| 12 | Red chase with trail |
| 13 | Green chase with trail |
| 14 | Blue chase with trail |
| 15 | White chase with trail |
| 16 | RGB chase with trail |
| 17 | Rainbow chase with trail |
| 18 | RGB chasing and fading |
| 19 | Red chasing green, chasing blue |
| 20 | Orange chasing purple, chasing cyan |
| 21 | Rainbow chase (7 colors) |
| 22 | Random twinkle: white over red |
| 23 | Random twinkle: white over green |
| 24 | Random twinkle: white over blue |
| 25 | White fading |
| 26 | Off |
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
info@luminii.com
www.luminii.com
Documents / Resources
 | ilight Plexineon Suspended Dynamic Color [pdf] Installation Guide Plexineon Suspended Dynamic Color, Plexineon, Plexineon Dynamic Color, Suspended Dynamic Color, Dynamic Color, Plexineon Suspended Mount Dynamic Color, Plexineon Rings Suspended Mount Dynamic Color |
