ikan PT4500-SDI / PT4700-SDI High Bright Beam Splitter Teleprompter User Guide

High Bright Beam Splitter Teleprompter

High Bright Beam Splitter Teleprompter

Quick Start Guide
PT4500-SDI / PT4700-SDI
High Bright Beam Splitter Teleprompter w/ 3G-SDI, HDMI, & VGA

What’s Included

▢ 1 x Teleprompter Base
▢ 1 x Bracket with Glass
▢ 1 x Teleprompter Hood with Boot
▢ 1 x Monitor
▢ 1 x AC Adapter with Cord
▢ 1 x PrompterPro Software
▢ 1 x Counterweight Set (2 x 2.5 lbs)
▢ 2 x D-Ring ¼-20″ Screws
▢ 2 x Hex Keys
▢ 3 x Different Height Risers

www.ikancorp.com | 1.713.272.8822 | [email protected] because we’re filmmakers too

Assembly Steps

Step 1

Remove the monitor mounts from the teleprompter base using the included larger 4mm hex key to loosen from the 15mm rods.

monitor mounts

Step 2

Attach the monitor mounts on the back of the monitor’s VESA compatible threads using the 4 included screws and provided 2mm hex key.

screws setup monitor

Step 3

After the monitor mounts are attached, adjust the 15mm rods to accommodate the monitor. Leave about 1 inch of room for the teleprompter bracket. Make sure the 15mm rods go through both set of monitor mounts. Please ensure that all screws are properly tightened after inserting the monitor. *SAFETY NOTE* Make sure to leave at least 2 inches of the rods inside the teleprompter base.

Teleprompter Base
Step 4

While sliding the teleprompter bracket into the slot of the teleprompter base pull on the red knob to allow the bracket to fully slide in.

teleprompter bracket

Step 5

Once the bracket is in place, tighten the side screw to lock in place. Double check and make sure all the screws are tightened with the included hex keys.

side screw lock

Step 6 (optional)
Should the teleprompter be too front heavy, you can attach the included counter weight on the back of the teleprompter base.

Specifications

PT4500-SDI

Aspect Ratio

4:3

Backlight

LED

Brightness

1000 nits

Build Material

Aluminum

Diagonal

15”

Input Signal

3G-SDI, VGA, HDMI

Input Voltage

DC 12v / 4A

Power Consumption

10W

Reading Range

17’

Resolution

1280 x 1024

Viewing Angle

160° (H) / 170° (V)

Weight

22 lb

Shipping Weight

28 lb

Shipping Dimensions

25 x 20 x 15.5 in

PT4700-SDI

Aspect Ratio

4:3

Backlight

LED

Brightness

1000 nits

Build Material

Aluminum

Diagonal

17”

Input Signal

3G-SDI, VGA, HDMI

Input Voltage

DC 12v / 4A

Power Consumption

10W

Reading Range

20’

Resolution

1280 x 1024

Viewing Angle

160° (H) / 170° (V)

Weight

23 lb

Shipping Weight

29 lb

Shipping Dimensions

25 x 20 x 15.5 in

Optional Accessories

PT4500-G Replacement Glass for both PT4500-SDI / PT4700-SDI
PT-CASE-V2 Rolling Hard Case for PT4500-SDI / PT4700-SDI Teleprompter

Learn More
More dynamic information at official website: www.ikancorp.com
Support
Contact email: [email protected]

CONDITIONS OF WARRANTY SERVICE

  • Free service for one year from the day of purchase if the problem is caused by manufacturing errors.
  • The components and maintenance service fee will be charged if the warranty period is expired.

Free Service will not be Provided in the Following Situations:(*Even if the product is still within the warranty period.)

  • Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.
  • Damage caused by natural disaster, abnormal voltage, and environmental factors, etc.

©2018 ikan Corporation. All rights reserved
www.ikancorp.com | 1.713.272.8822 | [email protected]
because we’re filmmakers too

Documents / Resources

ikan PT4500-SDI / PT4700-SDI High Bright Beam Splitter Teleprompter [pdf] User Guide
PT4500-SDI, PT4700-SDI, High Bright Beam Splitter Teleprompter with 3G-SDI HDMI VGA

References

Leave a comment

Your email address will not be published.