ZigBee Smart plug
Akwụkwọ ntuziaka onye ọrụ

Okwu Mmalite ngwaahịa

Ibu ngwaọrụ erughị otu kilogram. A na-atụ aro ịdị elu nwụnye nke na-erughị 1 m.

Ntuziaka nwụnye

1. Gbanyụọ ike Iji zere ihe ịma jijiji eletrik, biko kpọtụrụ onye na-ere ahịa ma ọ bụ ọkachamara tozuru etozu maka enyemaka mgbe ị na-etinye na ịrụzi.
2. Ntuziaka wiring
   Gbaa mbọ hụ na wiwi ziri ezi tupu ịgbanye ngwaọrụ ahụ ọkụ. S1/S2 can connect with the rocker light switch, or it doesn’t connect. To ensure safety, do not connect the neutral wire and live wire to it.

Nkọwapụta

Ụdị ngwaahịa	Zigbee Smart nkwụnye
Ntinye	100-240VAC 50/60Hz
Mpụta	100-240VAC 50/60Hz
Ibu. Ibu	10A/13A/16A/20A
ZigBee	IEEE 802.15.4 2.4GHZ
Ihe onwunwe	PC VO

Atụmatụ

ZigBee plug is a smart Plug that adopts the ZigBee plug wireless protocol and connects to your internet through the ZigBee hub. You can turn on/off, schedule on/off, and share the device with your family to control together, and so on.

Njikwa anya	Usoro nhazi oge
Njikwa olu	Kekọrịta njikwa
Ebe Obibi

The above functions are determined by the ZigBee Hub.

Ntuziaka ọrụ

1. Budata APP
   Please refer to the user guide of the hub to download the corresponding APP. below platforms are recommended:

   Ihe Smart	Amazon Alexa	Hue

2. Njikọ njikọ
   Set the hub according to the user guide. Support ZigBee plug hubs as follows:
   Echo Studio
   Echo Plus (ihe atụ: ZE39KL)
   Ihe ngosi Gen Echo nke abụọ (ihe atụ: DW2JL)
   2nd Gen Echo Plus (ihe atụ: L9D29R)
   Samsung SmartThings hub
   Philips hue
   Ọ bụrụ na njikọ ahụ ada ada, biko bugharịa oghere nso na ekwentị gị wee nwaa ọzọ.
3. Ike na
   Mgbe ịgbanyechara ya, ngwaọrụ ahụ ga-abanye n'ọnọdụ njikọta n'oge ojiji mbụ, akara ngosi LED na-enwu.
    The device will exit the pairing mode if no next operation for a long time. If you enter again, please long-press the manual switch for 5s until the LED signal indicator flashes and release.
4. Jikọọ na Alexa
   1. Power on the Plug
   2. Ask, “Alexa, discover devices!
   3. Plug ashes once it’s connected
   4. Wait until Alexa finishes, check the new devices” First/Second….plug”

Jikọọ na SmartThings

1. Power up the smart bulb, bulb breathe 3 times, and enter the configuration state.
2. Open the SmartThings app, and click”+”, click “Device”, click “SmartThings”, click “Lighting”, click ” Smart Bulb”, click “Start”, click “Next”, click “Skip the step”, click “Done”

Ntọgharị ụlọ nrụpụta

Long-press the configuration button for 5s until the LED signal indicator flashes and release, then the reset is successful. The device enters spairing mode.

If you pair the device with the hub again, please reset the device to factory default.

Emebere na china

Akwụkwọ / akụrụngwa

ZigBee Light Switch Module [pdf] Akwụkwọ ntuziaka onye ọrụ Module Mgbanwe ọkụ, Mgbanwe Module, Modul

Ntụaka

• Akwụkwọ ntuziaka onye ọrụ