Igwefoto PTZ Wi-Fi Smart
Ntuziaka onye ọrụ
Daalụ maka ịzụrụ UMOVAL Wi-Fi Nchekwa Igwefoto IP! Biko gụọ ntuziaka ahụ nke ọma tupu iji ngwaọrụ ma debe ya maka ntụnye aka ọzọ.
Biko rụba ama: The indoor PTZ IP Cameras support dual band Wi-Fi both 2.4GHz and 5GHz. But the outdoor PTZ IP cameras only supports Wi-Fi 2.4GHz router. Please make sure that your router is compatible with the camera device and your phone is connected to Wi-Fi router before connecting the device.
1. Olee otú ibudata APP?
Kwụpụ 1: Search the keyword “YCC365 Plus” in Apple Store or Android APP Store to download APP.
Kwụpụ 2: Or scan the QR code to download APP.
2. Otu esi etinye ngwaọrụ gị na APP & Jikọọ igwefoto?
2.1 Debanye aha akaụntụ ọhụrụ
Kwụpụ 1: If it is the first time for you to use the APP, you need to register a new account by your email. Please click “Sign Up” and register an account according to the procedure, or Log in with your mobile phone number.
Kwụpụ 2: Ọ bụrụ na ịchefu paswọọdụ gị, ị nwere ike ịtọgharịa paswọọdụ gị, pịa "Chefuru okwuntughe" na ibe nbanye.
Cheta na: Password should be at least 6 characters and no more than 26 characters. It should be av combination of letters and numbers. Only support mobile phone number registration in some regions. Otherwise please use email address to register in other regions.
2.2 Jikọọ igwefoto
2.2.1 Scan QR Code to Connect
Kwụpụ 1: Please make sure that your phone has been connected to Wi-Fi router.
Kwụpụ 2: Select your own Wi-Fi router and enter the router password.
Kwụpụ 3: Scan QR code on the APP interface by the camera lens toward it (Please keep QR code and camera lens in a straight line at a distance of 10-20cm).
Kwụpụ 4: Click the button “You hear a tone or the indicator light” after you hearing the voice of beep. Then please wait for the connecting, and the connection process will take around 1 or 2 minutes. Please wait for a moment. The connection will be done successfully when you hear a voice “Welcome to use the device!”
Ihe dị mkpa: It will pop up and display a short message “You may choose 5G Wi-Fi, please confirm whether the camera supports the 5G frequency band, otherwise the addition will fail”. Please click the button “Support 5G” no matter you Wi-Fi router is 2.4GHz or 5GHz in order to proceed.
2.2.2 Njikọ site na eriri netwọk
Biko rụba ama: Only Support LAN Port Device, such as Outdoor PTZ IP Cameras, not Indoor PTZ IP Cameras.
Kwụpụ 1: Click the button + in the upper right comer on the APP interface.
Kwụpụ 2: Choose the device type “Intelligent camera”, and then choose “Addition by connecting to network cable”.
Kwụpụ 3: Plug in the power adapter to the camera, and make sure the device LAN port is connected to network cable. And then scan QR code displayed on the upper side of device body.
Kwụpụ 4: Please wait for a moment. The connection will be done successfully in around 1 minute when you hear a voice “Welcome to use the device!”
2.2.3 Njikọ site na AP Hotspot
Kwụpụ 1: Click the button + in the upper right corner on the APP interface.
Kwụpụ 2: Choose the device type “Intelligent camera”, and then choose “Addition of AP hotspot”.
Kwụpụ 3: Plug in the power adapter to the camera, and then wait patiently for the device to operate by itself and you will hear a tone “Please connect your device by AP hotspot or scanning code”. Now it is time for you to click the button of Next to proceed.
Biko rụba ama: If you don’t see any tips, your camera may be connected by other ways, such as Connect by Scanning QR Code or by Network Cable. Please delete the current collection on your APP interface.
Kwụpụ 4: Please go to the Wi-Fi list and find the name “CLOUDCAM_XXXX”. Click it to go ahead and your mobile device will connect with the camera hotspot successfully soon and display in blue. Then please click the button < in the upper left corner to return to APP interface after hotspot connection.
Kwụpụ 5: Please click the button of Next on the returned interface and come to the interface of “Connect to Wi Fi”. Then choose your Wi-Fi router and input correct Wi-Fi password. At last, click the button of Confirm, which will take around 1 minute to finish AP hotspot connection finally.
3. Otu esi eji igwefoto maka ọrụ ndị ọzọ?
3.1 Live Preview Interface & Eserese
|A: Menu||B: HD/SD|
|C: Sound||D: Snapshot|
|E: Hold to Talk||F: Record Video to Your Phone or Tablet|
|G: Full Screen||H: Cloud Storage|
|I: Start Alarm Recording||J: Cloud Album|
|K: Control Panel||L: Nghaghachi vidiyo|
3.2 PTZ/Tọgharịrị PTZ
You can control the camera’s rotation angle by clicking the upper or bottom, left or right side on the steering wheel.
(1) Turn Off.
(2) PTZ Reset.
(3) Presets: Click the Presets icon to enter the preset management interface.
(6) Notice: Preset notice on Motion Detection, Sound Detection and Notification Frequency.
Cheta na: The actual display interface may prevail since different camera models have different functions.
3.3 Video ọkpụkpọ
Kwụpụ 1: Click the button of “Playback” at the right bottom corner on the live interface to view the playback videos.
Kwụpụ 2: Then please switch playback path to view Cloud Playback or Memory Card Playback.
Kwụpụ 3: The video playback will perform by itself. But you can adjust the target time to view video playback.
Cheta na: No playback videos if no memory card inserted into the camera or your cloud storage service is over 1-month free service period.
Kwụpụ 1: Click the symbol on the right bottom of connected camera interface. And a new interface will pop up on the bottom of the APP total interface.
Kwụpụ 2: Then click the symbol of Settings to open another interface to find the choice of “Sharing equipment”.
Kwụpụ 3: Click the button of “Sharing equipment >” to open a new interface and add family members & authorize more users.
4. Ntọala mmasị
Pịa bọtịnụ nke Ntọala na ndụ viewing interface ka ịlele menu nke Ntọala Mmasị. Ma biko mee ntọala dịka mmasị gị siri dị.
5. Kewaa ihuenyo ka View Vidiyo dị ndụ dị iche iche
The split-screen mode is only for multiple cameras operating at a same APP account.
Click the split-screen button to realize simultaneous view nke otutu igwefoto.
Cheta na: The split-screen mode will be working for more than two cameras.
6. Kedu otu esi eji igwefoto na kọmpụta?
Kwụpụ 1: Banye na websaịtị www.ucloudcam.com
Kwụpụ 2: Enter your account number and password, click to Login go ahead.
Cheta na: Please create your own account by clicking Sign Up if you don’t have an account.
7. Mụtakwuo maka ngwaọrụ
|Live dịpụrụ adịpụ View||
|E27/Inside||AC / DC||
AC / DC
8. Kedu ihe agụnyere na ngwugwu ahụ?
Ụdị dị iche iche ga-enwe ihe dị iche iche na ngwugwu. Biko lelee ha ka imepechara igbe ngwugwu.
8.1 What’s included in the Package Box of Model # UM-DOG-CAM 01?
1 x Indoor WiFi PTZ Camera
1 x USB nkwụnye ọkụ
1 x USB Electric Data Cable
3 x Screws & Plastic Stopper
1 x Akwụkwọ ntuziaka ndị ọrụ
8.2 Kedu ihe agụnyere na Igbe Ngwunye Ihe Nlereanya # UM-LAMP-CAM -02?
1 x Indoor E27 WIFi PTZ Camera
1 x E27 Socket
2 x Screws & Plastic Stopper
1 x Ntuziaka onye ọrụ
8.3 What’s included in the Package Box of Model # UM20-2MP-16 & UM25-2MP-12?
1 x Outdoor WiFi PTZ Camera
1 x AC/DC Power Adapter
4 x Screws & Plastic Stopper
1 x Waterproof Rubber Ring & Plastic Set
1 x Screwdriver Tool for Installation
1 x Ntuziaka onye ọrụ
9. Kedu ka esi etinye igwefoto n'ụzọ ziri ezi?
Enwere ike itinye igwefoto site na Mee N'onwe Gị. Mana nrụnye waya eletrik ka a na-atụ aro ka ọ bụrụ ọkachamara eletrik. Enwere ọdịiche nwụnye n'etiti igwefoto PTZ ime ụlọ na n'èzí. Na maka ime ụlọ PTZ IP ese foto na E27 lamp Igwefoto IP, nrụnye ga-adịkwa iche. Biko tinye E27 lamp IP cameras directly by screwing it into E27 socket. The details on how to install outdoor PTZ cameras are as below:
Kwụpụ 1: Locate the position where the camera will be installed. And please make sure the Wi-Fi signal is strong by checking your mobile phone Wi-Fi signal status over there.
Kwụpụ 2: Mark holes on the wall before drill holes.
Kwụpụ 3: Drill holes with an electric drill tools and insert the plastic stopper into the holes.
Kwụpụ 4: Keep the camera in the correct position and tighten the screws to fix the camera.
Ihe dị mkpa: As for the outdoor PTZ cameras with LAN port, please cover the LAN port with waterproof rubber & plastic ring for IP67 protection. Or please seal the LAN port with glues on the LAN port if the outdoor PTZ cameras are connected by wireless Wi-Fi router.
10. Olee otú iji tọgharịa igwefoto?
Kwụpụ 1: Biko view the displayed picture as below to find the Reset button.
Kwụpụ 2: The button of Reset is located inside the end of one of the three lines.
Kwụpụ 3: Please open the plastic over and you will find a Round Black Button. Here is the Reset Button.
Kwụpụ 4: Please press the Round Black Button to reset your camera to be the original settings in the factory.
11. Ajụjụ/ajụjụ a na-ajụkarị
Ajụjụ 1: Cannot connect the camera?
Ihe Mere 1: Please make sure the camera has been reset. Please disconnect the power adapter and insert it again. Or press the Reset button to set it again. The camera has been reset successfully if you hear a prompt tone.
Ihe Mere 2: Some cameras only support Wi-Fi 2.4GHz router. Please check your Wi-Fi router for more information. If your Wi-Fi router is 5GHz, please check whether it supports 2.4/5GHz dual modes.
Ihe Mere 3: Please confirm that the camera hasn’t been bound by other accounts.
Ajụjụ 2: How many different prompt tones?
There are totally four prompt tones during the configuring progress.
Prompt Tone 1: “Please configure camera by AP hotspot or scanning code”.
Prompt Tone 2: Select your Wi-Fi and login with your password, after the device makes a prompt tone like “beep” you will hear the prompt tone “Please wait for Wi-Fi connecting”.
Prompt Tone 3: "Biko chere maka njikọ ịntanetị" mgbe ị nwetasịrị adreesị IP ịntanetị.
Prompt Tone 4: “Internet connected. Welcome to use cloud camera”.
Ngwọta 1: If cannot hear the Prompt Tone 1 in 10 minutes, the camera may be out of work. Please contact the seller or UMOVAL service team for customer support.
Ngwọta 2: If cannot hear the Prompt Tone 2 in 5 minutes, please check whether your Wi-Fi channel has been hidden and the Wi-Fi router is far from the camera. If not resolved by this way, please scan the QR code to connect the camera.
Ngwọta 3: If cannot hear the Prompt Tone 3 in 5 minutes, please reduce the quantity of Wi-Fi users, and delete the special characters of your Wi-Fi password.
Ngwọta 4: If cannot hear the Prompt Tone 4 in 5 minutes, please try again. If it still doesn’t work, please contact the seller for customer supports.
Question 3: Why is the video recording intermittent?
Azịza: The cloud service may be trial order. And the alarm recording mode and the TF card event recording mode will only record when an abnormality is detected. That’s why the recording may not be continuous.
Question 4: Why is the camera disconnected?
Azịza: Please check whether the Wi-Fi router or the power adapter is disconnected? If they are connected correctly, please restart camera or delete the camera on APP and try to reconnect the camera.
Question 5: How to add family members as authorized users?
Azịza: Go to APP homepage, and Click the button of Settings to choose Sharing Equipment, then add family members according to the procedures step by step.
Question 6: How many users can access an account at the same time?
Azịza: Totally 10 users can access an account at the same time. But a same APP account can support 3 users to view vidiyo dị ndụ n'otu oge.
Question 7: Why can’t my Micro SD card be recognized?
Azịza: Please check whether the TF card meet the quality requirements or not. And brand Micro SD card is recommended to you for local storage. In addition, Wi-Fi signal may be so poor that Micro SD card cannot be read. Please adjust your Wi-R router or camera’s position to get strong Wi-Fi signal.
Question 8: The recording timeline is blank because the cloud service expires.
Solutions: The video cannot be replayed if the cloud service has been expired. And the video cannot be recorded if there is no TF card inserted into the camera.
If the TF card can work correctly, but the video recording file disappeared, please check the Micro SD card status by clicking the button “Memory card management”.
If the memory card is working normally in the application but no video has been recorded, please format the TF card. If it still cannot be used, please replace it with a new TF card and try again.
Cheta na: The free cloud storage service period is only one month. Please use Micro SD card for local video storage or buy cloud storage service in one month if you’d like to use video playback.
Question 9: Why cannot read the wireless network name after connecting to iOS and Android devices?
Solutions: Connect iOS or Android devices to Wi-Fi network through configuration, and then add the camera, which can help to read the network name automatically.
iPhone Android iOS/Android Tablet
Question 10: Why can’t I switch to another account to configure the camera Wi-Fi?
Solutions: The camera can only be bound to one main user’s account, and other accounts can only be viewed site na usoro nkekọrịta. Biko hichapụ igwefoto na interface APP na mbụ ma ọ bụrụ na akaụntụ ndị ọzọ kwesịrị ịhazigharị igwefoto dịka onye ọrụ isi.
Question 11: How to connect my camera to other Wi-Fi router?
There are two ways connect your camera to other Wi-Fi router as follows:
1 usoro: Setting >> Network information >> Select a New Wi-Fi.
2 usoro: Please try to reset your device in the APP interface when the camera is removed to another location and it display “Offline”. Click “Troubleshooting” and reset the camera, and then add Wi-Fi again.
12. Akpachara anya & Nkwado ndị ahịa
Akpachara anya 1: The User’s Manual is only for reference. And please adhere to your actual product while using it.
Akpachara anya 2: If there are any software or APP upgrades without notice, please do it according to updated instructions.
Akpachara anya 3: If you have any problems when using the camera, please contact the seller or UMOVAL customer service team for supports.
Akpachara anya 4: We have tried our best to ensure the completeness and accuracy of contents in the instructions. However, there may be some data without being listed. Please refer to UMOVAL customer supports if there is any deviation or questions from you.
Vidiyo ntuziaka mmalite
There is a Guide Video displayed on the APP interface if your camera has not been connected Please click the Starter Guide Video to learn more on how to use your device correctly.
UMOVAL is a trustable company and we will sincerely do customer supports for all of customers if there are any quality issues during the usages of the camera within the limited warranty period in 12 months since your order date.
Adreesị email nkwado ndị ahịa anyị dị ka n'okpuru:
Nabata ịkpọtụrụ anyị site na email ma ọ bụrụ na enwere nsogbu ma ọ bụ ajụjụ ọ bụla!
Inye ya UMOVAL IoT Technology Co., Ltd
Akwụkwọ / akụrụngwa
|UMOVAL YCC365 Smart Wi-Fi Igwefoto PTZ [pdf] Akwụkwọ ntuziaka onye ọrụ|
YCC365, Smart Wi-Fi PTZ Camera, YCC365 Smart Wi-Fi PTZ Camera