iPRO LOGOIgbe nkwụnye
ntụziaka Manual
iPRO WVQJB500 W Adapter BoxModel Ee e
WV-QJB500-W
WV-QJB500-S
WV-QJB500-G

anya

  • Ejila ihe nkwado a ma e wezụga iji kamera kwesịrị ekwesị.
    Eleghara anya nke a nwere ike ibute ọdịda na-ebute mmerụ ahụ ma ọ bụ ihe ọghọm.
  • Gwa ndị na-ere ahia ọrụ nrụnye.
    Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or damage to the product.
    Jide n'aka na ịkpọtụrụ onye na -ere ahịa.
  • Wụnye ngwaahịa ahụ nke ọma na mgbidi ma ọ bụ n'uko ụlọ dịka ntuziaka nwụnye.
    Enweghị ike idebe ihe a nwere ike ibute mmerụ ahụ ma ọ bụ ihe ọghọm.
  • Ejila aka gị tee nsọtụ akụkụ ọla.
    Ịghara ịhụ nke a nwere ike bute mmerụ ahụ.

Mgbe ị na-eji ngwaahịa a, gụọkwa “Mkpachapụ anya” akọwapụtara na ntuziaka ka a ga-esi tinye igwefoto na igwefoto. 

okwu mmalite
Use this product when performing outdoor wiring of a box-type camera for outdoor or a wall mount bracket such as using a conduit.
For the latest information about the supported cameras, refer to our support websaịtị
(https://i-pro.com/global/en/surveillance/training_support/support/technical_information<ControlNo.:C0501,C0502>).

nkọwa

Ihere ọrụ okpomọkụ: -50C ruo +60C (-58°F ruo +140°F)
akụkụ: 115mm (W) x 115 mm (H) x 40 mm (D)
(4-17/32 inches (W) x 4-17/32 inches (H) x 1-11/16 inches (D))
Nkume: Approx. 430 g (0.95 Ibs)
imecha: Base bracket: Aluminum die cast
Attachment plate: Stainless
WV-QJB500-W: i-PRO white
WV-QJB500-S: Silver
VW-QJB500-G: Light gray

* This product consists of an attachment plate and a base bracket and they are separately packaged.

Mgbochi maka ntinye

  • In order to prevent injury, the product must be securely mounted to a ceiling or wall according to the Installation Guide of this bracket.
  • Jide n'aka wepu ngwaahịa a ma ọ bụrụ na agaghịzi eji ya.

Nkọwa ọkọlọtọ

Operating Instructions (this document) …….. 1 pc.
Installed auxiliary wire* ………………………….. 1 pc.
Hexagon screw …………………………………. 5 pcs.
(M4 × 14 mm {9/16 inches}) (of them, 1 for spare)
Fixing screws for attachment plate ………… 5 pcs.
(M4 × 10 mm {13/32 inches}) (of them, 1 for spare)
Screw for temporary fixing …………………… 2 pcs.
(M3 × 3.5 mm {1/8 inches}) (of them, 1 for spare)

* An installed auxiliary wire is equipped with the attachment plate. 

Ihe ndị ọzọ dị mkpa (anaghị etinye ya)
Fixing screws (M4) …………………. 4 pcs.
DỊ mKPA

Nkwadebe

Remove the tape fixing installed auxiliary wire (accessory) on the attachment plate.
When installing another bracket on this product
The following are descriptions of how to install WV-QWL500-W (Wall Mount Bracket) on this product as an example.

  1. Remove the installed auxiliary wire (accessory) from the attachment plate. iPRO WVQJB500 W Adapter Box - FIG 1
  2. Attach the screw for temporary fixing (accessory) to the bracket to be installed on this product.iPRO WVQJB500 W Adapter Box - FIG 2 Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}
  3. If necessary, install the attachment plate provided with the camera to WV-QWL500-W by following the instructions described in the Operating Instructions of WV-QWL500-W.

Mgbe ị na-eji conduit

  • Remove the cap for the female or thread for the conduit using a 5 mm hex wrench and attach the conduit.
    The female thread for the conduit is compliant with ANSI NPSM (parallel pipe threads) 3/4 or ISO 228-1 (parallel pipe threads) G3/4.

iPRO WVQJB500 W Adapter Box - FIG 3

nwụnye

Step 1: Process the installation surface.
(Screw holes (4 places)/ Cable access hole (1 place))
When directly installing this product, process the installation surface.
Cheta na:

  • Determine the fixing screw hole diameter and depth in accordance with the specifications of the screws or anchors (x4) (M4: locally procured).
  • When wiring using a conduit, it is unnecessary to process the cable access hole on the installation surface. Make a fixing screw hole so that the cable access hole (for conduit) of the base bracket is arranged in the direction of the conduit.

Depending on the condition of the ceiling or the wall surface, the following five patterns of screw positions are available for fixation of the base bracket. Use only the holes of the same pattern (A – E) for mounting.

iPRO WVQJB500 W Adapter Box - FIG 4

vetikal kehoraizin
A 83.5 mm {3-9/32 inch} (82.5 mm {3-1/4 inch}) 46 mm {1-13/16 inch} (47.6 mm {1-7/8 inch})
B 46 mm {1-13/16 inch} (47.6 mm {1-7/8 inch}) 83.5 mm {3-9/32 inch} (82.5 mm {3-1/4 inch})
C* 83.5 mm {3-9/32 inch} (83.3 mm {3-9/32 inch}) -
D* - 83.5 mm {3-9/32 inch} (83.3 mm {3-9/32 inch})
E 63 mm (2-15/32 inches} 63 mm (2-15/32 inches}

* When mounting to a single-gang junction box, fix with two fixing screws (M4: locally procured) using the holes of either pattern C or D.

Kwụpụ 2: Fix the base bracket on the installation surface or on a junction box.
Pass the cables through the base bracket and then fix the base bracket on the installation surface or on a junction box (locally procured) with fixing screws (M4: locally procured).
When installing the base bracket on the installation surface
Cheta na:

  • When installing this product outdoors, be sure to apply waterproofing to the cable access hole and the holes for fixing the screw.

iPRO WVQJB500 W Adapter Box - FIG 5The illustration shown on the left is an example when installing on a wall using the combination of the fixing screw holes that is 83.5mm {3-9/32inches} × 46mm {1-13/16inches}.

■ When mounting the base bracket to a junction box
Select the holes on the base bracket so that they match with the screw holes of the junction box.
Cheta na:

  • When using a two-gang junction box, it is recommended that the boxes are arranged side by side as shown in the illustration below. (The cable connection work on the empty box side will become easier.)

iPRO WVQJB500 W Adapter Box - FIG 6

Step 3: Fix the attachment plate.
Fix the attachment plate with four fixing screws for the attachment plate (M4: accessory).
Recommended tightening torque: 1.37 N·m {1.01 lbf ft}

iPRO WVQJB500 W Adapter Box - FIG 7

Cheta na:

  • When wiring using a conduit, complete the connection work on the base bracket side before fixing the attachment plate.
  • When installing this product on a wall, fix the attachment plate with the “TOP⇧” mark facing upward.
  • When installing this product on a ceiling, fix the attachment plate so that the “TOP⇧” mark is faced in the direction where the camera is aiming at.

Kwụpụ 4: Install a camera or other bracket on this product.
■ When installing a camera
The following are descriptions of how to install WV-U1542L (outdoor box type) on a wall using this product as an example. The installation procedure is the same for other cameras.

  1. Hang the camera by hooking the installed auxiliary wire on this product on the hook on the rear of the camera mount base as shown in the illustration on the right.
  2. Connect the cables by following the instructions in the Installation Guide of the camera.
  3. Temporarily fix the camera mount base by hooking the screw for temporary fixing onto this product.iPRO WVQJB500 W Adapter Box - FIG 8iPRO WVQJB500 W Adapter Box - FIG 9
  4. Fix the camera on this product with four hexagon screws (M4: accessory) using a 3 mm hex wrench (locally procured).
    Recommended tightening torque: 1.37 N·m {1.01 lbf ft}
    iPRO WVQJB500 W Adapter Box - FIG 10

■ When mounting another bracket
The following are descriptions of how to install WV-QWL500-W (Wall Mount Bracket) on this product as an example.

  1. Pass the cable through WV-QWL500-W and temporarily fix it by hooking the screw for temporary fixing onto this product.iPRO WVQJB500 W Adapter Box - FIG 11
  2. Fix WV-QWL500-W on this product with four hexagon screws (M4: accessory) using a 3 mm hex wrench (locally procured).
    Recommended tightening torque: 1.37 N·m {1.01 lbf ft}iPRO WVQJB500 W Adapter Box - FIG 12
  3. Install the camera by following the Operating Instructions of WV-QWL500-W.
  • Tupu ịgbalị ijikọ ma ọ bụ wụnye ngwaahịa a, biko gụọ ntuziaka ndị a nke ọma ma chekwaa akwụkwọ ntuziaka a maka iji ya mee ihe n'ọdịnihu.
  • Ọdịdị dị na mpụga na akụkụ ndị ọzọ egosiri na akwụkwọ ntuziaka a nwere ike ịdị iche na ngwaahịa n'ezie n'ime akụrụngwa nke na-agaghị egbochi iji ya rụọ ọrụ n'ihi mmelite ngwaahịa a.

i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.

Kpachara anya: Rịba ama:
• Before attempting to connect or operate this product, please read these instructions carefully. • This product is not suitable for use in locations where children are likely to be present.
• Do not install this product in locations where ordinary persons can easily
reach it.
• For information about screws and brackets required for installation, refer to the corresponding section of this document.

Maka US na Canada:
Ụlọ ọrụ i-PRO Americas Inc.
Maka Europe na mba ndị ọzọ:
i-PRO EMEA BV
https://www.i-pro.com/
© i-PRO Co., Ltd. 2022
iPRO WVQJB500 W Adapter Box - BAR CodeNs0520-1042
Ebiputara na China

Akwụkwọ / akụrụngwa

i-PRO WV-QJB500-W Adapter Box [pdf] Akwụkwọ ntuziaka
WV-QJB500-W, Adapter Box, WV-QJB500-W Adapter Box, Box

References

Hapụ ikwu

Na adreesị email gị agaghị bipụtara. Chọrọ ubi na- *