Ntuziaka onye ọrụ FURRION F2AA003ABBK n'uko elu
FURRION F2AA003ABBK Ceiling Mount

Thank you and congratulations for purchasing this Furrion product. Before operating your new product, please read these instructions carefully. This user manual contains information for safe use, installation and maintenance of the product.

Please keep this manual in a safe place for future reference. This will ensure safe use and reduce the risk of injury.
Be sure to pass on this manual to new owners of this product.
Onye nrụpụta anaghị anabata ọrụ maka mmebi ọ bụla n'ihi erubere iwu ndị a.

NKSTRKWU ND SA AHFR SA nchekwa

Akara ịdọ aka na ntị  ỊDỌ AKA NA NTỊ
This product is designed to be installed on wood stud or solid concrete ceilings. Before installing make sure the ceiling or mounting surface will safely support four times the combined weight of the mounted equipment, including its accessories. This product is designed to mount televisions and any accessories weighing up to 121 lbs (55 kg) to a properly rated ceiling structure.

Akara ịdọ aka na ntị ịkpachara anya

  • Never exceed the maximum load capacity of 121 lbs (55 kg). Serious injury or property damage may occur.
  • Improper installation may cause serious personal injury or damage to the product, which will void the warranty. It is recommended that a qualified person should install the ceiling mount.

Safety measures must be practiced at all times during the assembly of this product. Use proper safety equipment and tools for the assembly procedure to prevent personal injury.

  • At least two qualified people should perform the assembly procedure. Proper installation must be followed as outlined in these installation instructions. Personal injury and/or property damage can result from dropping or mishandling the TV.
  • Ensure that there are no missing or defective parts upon receipt. Never use defective parts.
  • This product contains small parts that could be a choking hazard.
  • The ceiling you affix the ceiling mount to must be capable of supporting four times the weight of the
    television and the mount combined. A professional installer or structural engineer should inspect or verify the requirements of the structure it is mounted to.
  • Do not use this product for any purpose other than to mount a VESA compliant TV on a vertical surface as outlined in this manual.
  • When mounting to metal structures or concrete ceilings, it is recommended to add an anchor (not included) to the TV, especially for areas where a lot of wind shear is expected.
  • Use an anchor (not included) in case you live in an area where inclement weather occurs regularly.
  • Always inspect mounting location for electrical wires, water, and natural gas lines prior to installation. Cutting or drilling into these utility lines may cause serious personal injury or property damage.
  • Do not install near sources of high heat.
  • Do not install on a structure that is prone to vibration, movement or likelihood of being stricken by other objects nearby.

IHE: The included hardware is for mounting to flat concrete surfaces concrete surfaces or wood trusses and ceiling structures. If you are uncertain about the nature of your wall, please consult your hardware or installation professional for proper mounting to types of walls.

Nchekwa PRESAUTION

  • Ensure these instructions are thoroughly understood before attempting installation. If unsure of any part of the installation process, contact a professional installer for assistance.
  • Ngwaahịa a bụ maka naanị ihe ezinaụlọ mere, yabụ na agaghị enwe ike iji ya n'ihu ọha dịka ụlọ oriri na ọ hotelsụ hotelsụ.
  • Debe ụmụaka na anụ ụlọ ka ha na -achịkọta ngwaahịa a.
  • Ekwela ka ụmụaka jiri ngwaahịa a gwuo egwu.
  • Ejila ngwaahịa a ma ọ bụrụ na akụkụ ọ bụla na-efu, mebiri emebi ma ọ bụ eyi.
  • Ejila ngwa ọrụ ike gbakọta ngwaahịa a. Ngwaọrụ ike nwere ike ihichapụ ma ọ bụ mebie akụkụ ahụ.
  • Iji zere ịkọcha ala, kpọkọta ngwaahịa na ala dị nro, dị ka kapeeti.
  • Be careful not to pinch fingers during installation.
  • Fasteners (hardware) must be tightly secured, but do not overtighten screws. Over tightening can damage the items, greatly reducing their holding power.
  • Jiri onye nnyemaaka ma ọ bụ igwe eji arụ ọrụ mgbe niile bulie ma bulie ngwa ọrụ n'enweghị nsogbu.
  • Safety gear and proper tools must be used. Failure to do so can result in property damage and/or serious injury.
  • Furrion recommends checking knobs, screws, and bolts every 2-6 months and after inclement weather conditions.

Ihe dị na igbe ahụ

IT

Igbe dị na Igbe

Ceiling Plate Paper Template x 1
UP

Igbe dị na Igbe

X XUMUM
LP

Igbe dị na Igbe

X XUMUM
MP

Igbe dị na Igbe

X XUMUM
AP

Igbe dị na Igbe

X XUMUM
A

Igbe dị na Igbe

(M8 x 63mm) x 4
B

Igbe dị na Igbe

(M9) x 4
C

Igbe dị na Igbe

Metal Anchor (M8 x 40) x 4
D

Igbe dị na Igbe

(M6 x 16mm) x 4
E

Igbe dị na Igbe

 (M6 x 18mm) x 4
F

Igbe dị na Igbe

 (M6 x 25mm) x 4
G

Igbe dị na Igbe

(M8 x 10mm) x 8
H

Igbe dị na Igbe

(M8 x 18mm) x 4
I

Igbe dị na Igbe

(M8 x 25mm) x 4
J

Igbe dị na Igbe

(M6/M8) x 4
K

Igbe dị na Igbe

(M6/M8) x 8
L

Igbe dị na Igbe

(M8 x 55mm) x 2
M

Igbe dị na Igbe

(M8)  x 2
N

Igbe dị na Igbe

(S10) x 1
O

Igbe dị na Igbe

(S6) x 1
P

Igbe dị na Igbe

(S13) x 1
Q

Igbe dị na Igbe

(M6 x 8mm) x 2

Igbe dị na Igbe

Ndenye Malite Guide x 1
Akwụkwọ ikike Akwụkwọ ntuziaka x 1

TOOLS NEED (NOT INCLUDED)

  • Phillips sikruuokwomoto
    Ngwa Ngwa
  • Onye nlegharị anya
    Ngwa Ngwa
  • Onye nchọta nchọta
    Ngwa Ngwa
  • Nlele
    Ngwa Ngwa
  • Power Dril
    Ngwa Ngwa
  • Drill Bit
    15/32″ (12 mm) for Concrete 1/4″ (6 mm) for wood stud
    Ngwa Ngwa
  • teepu
    Ngwa Ngwa
  • Mezie Measure
    Ngwa Ngwa
  • Ọkwa
    Ngwa Ngwa

CONFIGURE THE TV BRACKET

  1. Choose one kind of configuration from below A, B, C, D based on your TV and assemble the TV bracket.
    Ntụziaka nke ọgbakọ
  2. TV bracket expands to fit TV hole patterns from 315∕16″ x 315∕16″ (100 x 100mm) to 1515∕16″ x 1515∕16″ (400 x 400mm).
    Ntụziaka nke ọgbakọ
  3. Measure the width and height of your TV hole  pattern with a tape measure.
    Ntụziaka nke ọgbakọ
  4. Assemble the TV bracket with 4 adaptor bars  and 8 M8x10 screws (G) for below B, C or D
    configuration and keep the screws untightened, slight adjust the 4 adaptor bars to make the mounting holes aligned with the ones on the TV back, tighten the screws to fix the 4 adaptor bars.
    Ntụziaka nke ọgbakọ

Furrion Aurora™ TV VESA Mounting Pattern (W x H mm)

Size/ Mode FDU***CBS FDU***CBR FDU***CSA
43 " 200 x 200mm 200 x 200mm
49 " 200 x 400mm /
50 " / 200 x 400mm
55 " 400 x 400mm 400 x 200mm
65 " 400 x 400mm 400 x 200mm

nwụnye

Akara ịdọ aka na ntị ỊDỌ AKA NA NTỊ
When installing ceiling plate on cinder block, verify first that you have a minimum of 13/8″ of concrete thickness to be used for the concrete wall anchors (not included). Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1″ minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity. Concrete must be 2000 psi density minimum. Lighter density concrete may not hold anchor.

Akara ịdọ aka na ntị ịkpachara anya
Never try to hang a TV by yourself. Always use at least two people to lift the TV into place.

DỊ mKPA

  • Handle the TV in a vertical position to avoid damage to the screen. If placing the TV screen-side down or leaning against a wall during installation, cover the screen with a protective cloth or blanket.
  • Check your TV manual before attaching brackets to TV. Some models require attaching soundbar brackets in tandem with attaching TV brackets.

Determine the correct length and diameter of screws based on your TV hole patterns

  • If your TV back is flat, use the shorter screws with washers.
  • If your TV back is irregular or curved, use the longer screws with washers and spacers (K).
    For Furrion Aurora™ TV, please use the screw size M6x16 (D) and washers (J) to attach the TV bracket to TV back.

Assemble the configured TV bracket on the back of Furrion Aurora™ TV by using 4 x M6x16 screws (D) and washers (J). Ensure the bracket is vertically centered and leveled. Tighten the screws (D) to ensure the TV bracket securely attached on TV back.
Screw And Washer

Akara ịdọ aka na ntị ỊDỌ AKA NA NTỊ
Make sure to use the correct length screw for your TV. A screw that is too long might damage your TV.

Akara ịdọ aka na ntị ỊDỌ AKA NA NTỊ
Do not drill into mortar joints. Be sure to drill holes centered within studs or bricks.
Ntụziaka ntọala

  1. Use the ceiling plater paper template to mark below:
    • For wooden roof installation, mark A, B, C and D in the ceiling.
    • For concrete roof installation, mark a, b, c and d on the ceiling.
  2. Drill pilot holes into the circle marks (A, B, C, D or a, b, c, d).
    • For wooden roof installation, using a 1/4″ (6 mm) drill bit to drill 4 pilot holes (A, B, C and D). Then remove the wall mount paper template from wall.
      Pilot holes must be drilled to a depth of 3″ (75mm)
    • For concrete roof installation, using a 3/8″ (10 mm) drill bit to drill 4 pilot holes (a, b, c and d) into solid concrete. Pilot holes must be drilled to a depth of 19/16″ (40mm).
  3. Nwụnye gara n'ihu:
    • For wooden roof installation,, attach and fix the bracket to ceiling using screws (M8 x 63mm) and washers (M9).
    • For concrete roof installation, attach and fix the bracket to ceiling using metal anchor (M8 x 40).
      IHE: Use allen key and wrench to lock the rod by turning counterclockwise, otherwise to unlock. Ensure the rod is perpendicular to the ground.
  4. Attach TV mount bracket to the rod.
  5. Use 2 screws M8 x 55 mm (L) with M8 nuts (M) to fix the joint

    Akara ịdọ aka na ntị ịkpachara anya
    It is possible to dislodge your TV while you level it. Use extreme caution until you tighten the leveling and locking screws.
  6. Hook the top support of the TV mount onto the arm of the ceiling mount.
  7. Secure the TV to the ceiling mount using two screws (M6 x 8mm).
    IHE: You could turn the screws by hand to adjust the leveling of your TV. Once adjustment is finished, tighten the screws firmly in place, but do not over tighten. Over-tightening can damage the screws, greatly reducing their holding strength.
  8. This mount allows a rotation of the TV of 360°
    • rotate the TV to the desired location and then tighten all screws.

IHE: It is recommended to be protected between with the area near the wall and TV in case of damage from strong winds or some other collision.

nkọwapụta

Display Size: 43 – 65″ (1090 – 1650 mm)
Ibu Ibu: 121 lbs (kg 55)
Arịọnụ ternkpụrụ: 100 x 100 mm
200 x 100 mm
200 x 200 mm
300 x 200 mm
300 x 300 mm
400 x 200 mm
400 x 300 mm
400 x 400 mm
Oke tit: Up to 15° downwards
Oghere Pan/Swivel: Ruo 360 Celsius
Distance From Ceiling: 243/16 – 34″ (614 – 864 mm)

nkwado

Rlọ Ọrụ Innovation Furrion & Institute of Technology 

  • 52567 Independence Ct., Elkhart, NA 46514, USA

R 2007-2022 Furrion Ltd. Furrion® na akara Furrion buighalaahia edenyere maka ikikere ya site na Furrion Ltd. ma debanye aha ya na US na obodo ndị ọzọ.

Maka Ama Patent: www.furrion.com/pages/patents
Logo

 

Akwụkwọ / akụrụngwa

FURRION F2AA003ABBK Ceiling Mount [pdf] Ntuziaka onye ọrụ
F2AA003ABBK Ceiling Mount, F2AA003ABBK, Ceiling Mount

References

Hapụ ikwu

Na adreesị email gị agaghị bipụtara.