exile logowww.exileaudio.comMpụga Audio S50.4 Usoro SHIFT AMPNDỤ

Usoro SHIFT AMPNDỤ
AKW OKWỌ NWOKE
MODELS: S50.4 / S110.5 / S60.1 / S100.1 / S150.

WELCOME TO EXILE

Congratulations on purchasing your Exile amponye ndu. Biko gụọ akwụkwọ ntuziaka a ka ị ghọta nke ọma ka ị ga-esi nweta nsonaazụ kacha mma na ngwaahịa a wee hụ na a na-agbaso ndụmọdụ niile gbasara otu esi ele ngwaahịa ahụ.
Thank you for buying Exile, we hope you enjoy listening to your product as much as we enjoyed creating it.

Ntị

ịdọ aka na ntị 2 Odiyo nke azụ ahịa amplifier will place an additional load on the vehicle’s charging system. Most modern vehicles have sufficient capacity in the charging system as not all of the electrical components of the vehicle will be switched on at once.
Lelee ogo fiusi nke amplifier ma jiri nke a dị ka ihe kacha ugbu a chọrọ. N'ozuzu, eserese na-aga n'ihu ugbu a ga-abụ otu ụzọ n'ụzọ atọ nke ọnụ ọgụgụ kacha elu ugbu a.

atụmatụ

The Shift series amplifier offers big power in a compact chassis. This makes for easy installation in tight spaces without sacrificing any of the output. Shift amps utilize Class D efficiency and come packed with features to give you ultimate control over your audio. Whether you’re cruising the streets, getting muddy, or riding the waves Exile Audio has you covered with Shift series power ampndị na -enye ndụ.Mpụga Audio S50.4 Usoro SHIFT AMPLIFIERS - Fig1

  • Compact size with a high power output
  • Wired remote bass level controller
  • Bass boost frequency and level adjustment
  • Adjustable low pass and subsonic filters
  • High Efficiency, an energy-saving digital amplifier with a reliable full MOSFET design

SPECIFICATIONS Monoblock

AmpKlaasị na -eme mkpọtụ
Nzaghachi oge:
Mkpokọta Egwuregwu Egwuregwu
Ihe mgbaàmà nke Noise Ratio:
Nweta Range
Low Pass Crossover Range
Subsonic Crossover Range
Bass Boost 445Hz:
Njikwa Bass dịpụrụ adịpụ
Klas D
15 - 220Hz

70dB (1W)
0.2 - 5V
40 - 220Hz
OFF – 220Hz
0 ka + 12dB
Ee

U S60.1

Owa
Into 1 ohm
Into 2 ohm
Power/Ground Wire Size:
akụkụ:
1
400w x1
600w x1
4 nlele
L: 9.4in (239mm)
W: 5.9in (150mm)
H: 2.3in (58mm)

S100.1

Owa
Into 1 ohm
Into 2 ohms
Into 4 ohm
Power/Ground
Oke Waya:
akụkụ:
1
1000w x1
650w x1
400w x1
4 nlele
L: 14.0in (354mm)
W: 5.9in (150mm)
H: 2.3in (58mm)

S150. 1

Owa
Into 1 ohm
Into 2 ohm
Into 4 ohm
Power/Ground
Oke Waya:
akụkụ:
1
1500w x1
900w x1
500w x1
4 nlele
L: 17.5in (444mm)
W: 5.9in (150mm)
H: 2.3in (58mm)

SPECIFICATIONS Multichannel

Ampọkwa klas D
Nzaghachi oge:
Mkpokọta Egwuregwu Egwuregwu
Ihe mgbaàmà nke Noise Ratio:
Nweta Range
Low Pass Crossover Range
Subsonic Crossover Range
Bass Boost @ 45Hz:
remote Bass Control
klas D
20 - 20kHz

75dB (1W)
0.2 - 5V
50 - 750Hz
50 - 750Hz
0 ka + 18dB
NA

S50.4

Owa
Into 4 ohms
Into 2 ohm
Into 4 ohms Bridged
Power/Ground Wire Size
akụkụ
4
70w x4
110w x4
250w x2
4 NGW
L: 9.4in (239mm)
W: 5.9in (150mm)
H: 2.3in (58mm)

S110.5

Owa
Into 4 ohm
Into 2 ohms (Sub CH)
Power/Ground Wire Size
akụkụ
5
100w x4
530w x1
4 NGW
L: 15.0in (383)
W: 5.9in (150mm)
H: 2.3in (58mm)

Ọrụ njikwa

S60.1/S100.1/S150.1

Mpụga Audio S50.4 Usoro SHIFT AMPLIFIERS - Fig2

  1.  Ekwu okwu
    Connect speaker/subwoofers to these terminals. Be sure to check the wire for proper polarity. Never connect the speaker cables to the chassis ground.
  2.  +12V POWER
    Jikọọ ọnụ ọnụ a site na FUSE ma ọ bụ CIRCUIT BREAKER na njedebe dị mma nke batrị ụgbọ ala ma ọ bụ njedebe dị mma nke batrị sistemụ ọdịyo dịpụrụ adịpụ.
    Amụma: Always protect this power cable by installing a fuse or circuit breaker of the appropriate size within 18″ (45cm) of the battery terminal connection.
  3. REMOTE TURN ON (REM)
    Ebe njedebe a na-agbanye amplifier when +12 volts is applied to it. Connect it to the remote turn-on lead of the head unit or signal source.
  4. GND
    Connect this cable directly to the frame of the vehicle. Make sure the metal frame has been stripped of all paint down to the bare metal. Use the shortest distance possible. It is always a good idea to replace the factory ground at this time with a larger cable equal to the new amplifier power cable or larger.
    NKWUTA: Ejikọla ọnụ ọnụ a ozugbo na ọdụ ụgbọ ala batrị ma ọ bụ ebe ụlọ nrụpụta ọ bụla ọzọ.
  5. LIMIT / PROTECT / PWR
    The LIMIT LED (S100.1 / S150.1) will light up when the output is clipped or the amplifier gets overheated. When the limit indicator lights up, the amplifier will hold or reduce the output power to protect the subwoofer and amplifier. Please turn down the volume or cool down the amplifier when this indicator lights up continually.
    The red PROTECT LED will light up and will be flashing if there is a fault presented to the amponye ndu. Biko gbanyụọ njikọ ahụ amplifier ma dozie mmejọ ahụ tupu ị jikọọ ọzọ ampna -emegharị ihe.
    The green PWR LED will light up when the amplifier is powered on and working correctly.Mpụga Audio S50.4 Usoro SHIFT AMPLIFIERS - Fig3
  6. Gbanwee
    Connect the remote controller to control the Subwoofer amplifier volume from the driver seat location, for ease of adjustment during playing.
  7. ndenye
    These RCA input jacks are for use with source units that have RCA outputs. A source unit with a minimum level of 200mV is required for proper operation. The use of high-quality twisted pair cables is recommended to decrease the possibility of radiated noise entering the system.
  8. BASS BOOST / BASS BOOST FREQ
    This adjusts the boost level of the bass boost center frequency. It can be adjusted from 0 to 12dB, Combining with bass boost frequency (S150.1), you can accurately match the amplifier performance to woofer response.
  9. AGBA
    Njikwa ọkwa ga-adaba na uche nke ihe amplififiga na mgbama otu isi iyi voltage. The Operating range is 200mV minimum to 5V maximum. This is NOT a volume control!
  10. PDF
    This control is used to select the desired low pass x-over frequency. The frequency can be adjusted from 40Hz to 220Hz.
  11. ISIOKWU
    This control can filter out unwanted low frequencies from 1 0Hz (OFF) to 50Hz. This function will increase the power handling of your woofers.
  12. BRIDGE IN / BRIDGE OUT
    The BRIDGE IN jack receives a signal from the master amplifier when this amplifier is bridged as a slave. DO NOT use input jacks when the amplifier is working as a slave. All the functions will be adjusted by the master ampna -emegharị ihe.
    The BRIDGE OUT jack sends the bridge signal to another, same Shift-series amplifier in bridging configuration. All the functions will be adjusted by the master ampna -emegharị ihe.
  13. CLIP LIMIT This switch controls the output clip limit on/off. When switched on, the amplifier will control the output level at the clip point and reduce the distortion. This will keep your amplifier at a low distortion at the clipped signal.
  14. Q njikwa
    This knob adjusts the bass boost curve. Turning it to the narrow side will make the boosted frequency narrow and sharp, turn it to the wide will extend the boosted frequency range.

S50.4

Mpụga Audio S50.4 Usoro SHIFT AMPLIFIERS - Fig4

  1. Ekwu okwu
    Connect speaker/subwoofers to these terminals. Be sure to check the wire for proper polarity. Never connect the speaker cables to the chassis ground.
  2.  +12V POWER
    Jikọọ ọnụ ọnụ a site na FUSE ma ọ bụ CIRCUIT BREAKER na njedebe dị mma nke batrị ụgbọ ala ma ọ bụ njedebe dị mma nke batrị sistemụ ọdịyo dịpụrụ adịpụ.
    Amụma: Always protect this power cable by installing a fuse or circuit breaker of the appropriate size within 18″ (45cm) of the battery terminal connection.
  3. REMOTE TURN ON (REM)
    Ebe njedebe a na-agbanye amplifier when +12 volts is applied to it. Connect it to the remote turn-on lead of the head unit or signal source.
  4. GND
    Connect this cable directly to the frame of the vehicle. Make sure the metal frame has been stripped of all paint down to the bare metal. Use the shortest distance possible. It is always a good idea to replace the factory ground at this time with a larger cable equal to the new amplifier power cable or larger.
    NKWUTA: Ejikọla ọnụ ọnụ a ozugbo na ọdụ ụgbọ ala batrị ma ọ bụ ebe ụlọ nrụpụta ọ bụla ọzọ.
  5. ndenye
    These RCA input jacks are for use with source units that have RCA outputs. A source unit with a minimum level of 200mV is required for proper operation. The use of high-quality twisted pair cables is recommended to decrease the possibility of radiated noise entering the system.
  6. Ntinye nhọrọ
    This button selects either 2ch or 4ch input mode. When pressed in, the amplifier works in 2CH input, mode, CH-B input will be paralleled to CH-A, CH-B input jack will be a dummy. When pressed out, the amplifier will work in 4CH input mode.
  7. AGBA
    Njikwa ọkwa ga-adaba na uche nke ihe amplififiga na mgbama otu isi iyi voltage. The Operating range is 200mV minimum to 5V maximum. This is NOT a volume control!Mpụga Audio S50.4 Usoro SHIFT AMPLIFIERS - Fig5
  8. LPF/FUL/HPF SELECTOR & FREQUENCY ADJUST KNOB
    This switch and knob control Low Pass Filter, High Pass, and Full pass functions. When set to LPF, The amplifier will cut off high frequencies and should be used for driving subwoofers. When set to HPF, The amplifier will cut off low frequencies and should be used for driving full-range speakers or tweeters. When set to FULL, the Full range of frequencies is reproduced and outputted to the speakers. In another word, the filters are “OFF”.
  9. PROTECT / PWR
    The red PROTECT LED will light up and will be flashing if there is a fault presented to the amponye ndu. Biko gbanyụọ njikọ ahụ amplifier ma dozie mmejọ ahụ tupu ị jikọọ ọzọ ampna -emegharị ihe.
    The green PWR LED will light up when the amplifier is powered on and working correctly.
  10. Ntinye ntinye
    The amplifier has dual input sensitivity differential inputs which will receive either High level (Speaker output) or Low level (RCA) signals from your car stereo’s source unit. When switching to PRE IN, The signal can be delivered to the amplifier using the low-level RCA outputs on the source unit. When switching to SPK IN, The High-Level signal can be run from the source unit’s speaker outputs to the stereo RCA input on the end panel of the amplifier using a speaker to RCA adapter (not included).
  11. UTgbọala agbanye
    For auto turn on/off mode, there are three options: DC Offset/Rem/Audio.
    REM: When auto turns on to REM, please connect the unit REM terminal to the source unit remote terminal with an 18AWG cable. This is the preferred mode.
    DC Offset: If the OEM source unit has no REM signal output, you can choose DC Offset (Meanwhile, Input select switch to SPK IN mode), DC Offset can turn on/off amplifier by detecting the 6V DC Offset from the OEM source unit terminal.
    AUDIO: Audio mode can turn ON/OFF the amplifier by detecting the audio signal from the source unit. Note: If the volume is too Low, The amp may fail to turn on. Check if the source unit volume is properly set.

S110.5

Mpụga Audio S50.4 Usoro SHIFT AMPLIFIERS - Fig6

  1. Ekwu okwu
    Connect speaker/subwoofers to these terminals. Be sure to check the wire for proper polarity. Never connect the speaker cables to the chassis ground.
  2. +12V POWER
    Jikọọ ọnụ ọnụ a site na FUSE ma ọ bụ CIRCUIT BREAKER na njedebe dị mma nke batrị ụgbọ ala ma ọ bụ njedebe dị mma nke batrị sistemụ ọdịyo dịpụrụ adịpụ.
    Amụma: Always protect this power cable by installing a fuse or circuit breaker of the appropriate size within 18″ (45cm) of the battery terminal connection.
  3. REMOTE TURN ON (REM)
    Ebe njedebe a na-agbanye amplifier when +12 volts is applied to it. Connect it to the remote turn-on lead of the head unit or signal source.
  4. GND
    Connect this cable directly to the frame of the vehicle. Make sure the metal frame has been stripped of all paint down to the bare metal. Use the shortest distance possible. It is always a good idea to replace the factory ground at this time with a larger cable equal to the new amplifier power cable or larger.
    NKWUTA: Ejikọla ọnụ ọnụ a ozugbo na ọdụ ụgbọ ala batrị ma ọ bụ ebe ụlọ nrụpụta ọ bụla ọzọ.
  5. ndenye
    These RCA input jacks are for use with source units that have RCA outputs. A source unit with a minimum level of 200mV is required for proper operation. The use of high-quality twisted pair cables is recommended to decrease the possibility of radiated noise entering the system.
  6. Ntinye ntinye
    The amplifier has dual input sensitivity differential inputs which will receive either High level (Speaker output) or Low level (RCA) signals from your car stereo’s source unit. When switching to PRE IN, The signal can be delivered to the amplifier using the low-level RCA outputs on the source unit. When switching to SPK IN, The High-Level signal can be run from the source unit’s speaker outputs to the stereo RCA input on the end panel of the amplifier using a speaker to RCA adapter (not included).
  7. UTgbọala agbanye
    For auto turn on/off mode, there are three options: DC Offset/Rem/Audio.
    REM: When auto turns on to REM, please connect the unit REM terminal to the source unit remote terminal with an 18AWG cable. This is the preferred mode.
    DC Offset: If the OEM source unit has no REM signal output, you can choose DC Offset (Meanwhile, Input select switch to SPK IN mode), DC Offset can turn on/off amplifier by detecting the 6V DC Offset from the OEM source unit terminal.
    AUDIO: Audio mode can turn ON/OFF the amplifier by detecting the audio signal from the source unit. Note: If the volume is too Low, The amp may fail to turn on. Check if the source unit volume is properly set.Mpụga Audio S50.4 Usoro SHIFT AMPLIFIERS - Fig7
  8. AGBA
    Njikwa ọkwa ga-adaba na uche nke ihe amplififiga na mgbama otu isi iyi voltage. The Operating range is 200mV minimum to 5V maximum. This is NOT a volume control!
  9. HPF
    This control is used to set the HPF crossover frequency for the front amplifier channel. The frequency is adjustable between OFF and 200Hz.
  10. PROTECT / PWR
    The red PROTECT LED will light up and will be flashing if there is a fault presented to the amponye ndu. Biko gbanyụọ njikọ ahụ amplifier ma dozie mmejọ ahụ tupu ị jikọọ ọzọ ampna -emegharị ihe.
    The green PWR LED will light up when the amplifier is powered on and working correctly.
  11. Gbanwee
    Connect the remote controller to control the Subwoofer amplifier volume from the driver seat location, for ease of adjustment during playing.
  12. ISIOKWU
    This control can filter out the unwanted low frequencies from 1 0Hz (OFF) to 50Hz. This function will increase the power handling of your woofers.
  13. PDF
    This control is used to select the desired low pass x-over frequency. The frequency can be adjusted from 40Hz to 220Hz.
  14. MGBE OZI
    This switch adjusts the boost level of the bass boost center frequency. It can be adjusted from 0 to 6dB to 12dB.

N'ihu dijram

MONO AMPLIFIER WIRING (ONE WOOFER LOAD)

Mpụga Audio S50.4 Usoro SHIFT AMPLIFIERS - MONO AMPNDỤ

MONO AMPLIFIER WIRING (TWO WOOFER LOAD)

Mpụga Audio S50.4 Usoro SHIFT AMPLIFIERS - Fig8

NDU AMPLIFIER BRIDGE MODE

Mpụga Audio S50.4 Usoro SHIFT AMPLIFIERS - MONO AMPNDỤ 1

 Ntị
ịdọ aka na ntị 2Mgbe ejikọtara abụọ amplifiers you should use the same model ampndị na -enye ndụ.
Please make sure the negative speaker terminal of the two amplifiers is connected by the same gauge cables as the positive terminal being used.
DO NOT connect any signal cables to the input RCA jacks when bridged as a slave unit.
All the functions will be disabled on the slave amplifier when bridged. It will be adjusted by the master ampna -emegharị ihe.

Mpụga Audio S50.4 Usoro SHIFT AMPLIFIERS - WIRING DIAGRAMSMpụga Audio S50.4 Usoro SHIFT AMPLIFIERS - CHANNEL MODE

 

exile logo

Exile Audio Lake Oswego, OR USA
www.exileaudio.com

Mpụga Audio S50.4 Usoro SHIFT AMPLIFIERS - FigDesigned and Engineered in the USA.
Emebere na china

NKWUKWỤKWỌ LIMITED
Exile warrants this product to be free from defects in material and workmanship under normal use for a period of one year from the date of original purchase when purchased from an Authorized Exile Dealer. If the product is labeled B Stock/Refurbished and purchased from an Authorized Exile Dealer, it is warranted for 90 days from the date of purchase, regardless of the place of installation. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction during the warranty period, Exile will replace or repair (at its discretion) the defective merchandise with equivalent merchandise at no charge. Warranty replacements on B-Stock merchandise may have cosmetic scratches and blemishes. Discontinued products may be replaced with more current equivalent products. This warranty is valid only for the original purchaser and is not extended to owners of the product subsequent to the original purchaser. Any applicable implied warranties are limited in duration to a period of the express warranty as provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you. This warranty gives you specific legal rights; however, you may have other rights that vary from state to state. This warranty is only valid within the USA, for warranties outside of the USA consult the appropriate international distributor.
©2021 Exile Audio. All rights reserved. All logos are Trademarks or Registered Trademarks of Exile Audio.

Akwụkwọ / akụrụngwa

Mpụga Audio S50.4 Usoro SHIFT AMPNDỤ [pdf] Akwụkwọ ntuziaka onye nwe
Usoro SHIFT AMPLIFIERS, S50.4, S110.5, S60.1, S100.1, S150.1, AMPNDỤ

References

Hapụ ikwu

Na adreesị email gị agaghị bipụtara.