Introduction
This manual provides comprehensive instructions for the SF 77103PP02 Chrome Quartz Analog Digital Watch. Please read this manual carefully before using your watch to ensure proper operation and to maximize its lifespan. Keep this manual for future reference.
Product Overview
The SF 77103PP02 is a men's watch featuring both analog and digital time displays. It is designed for durability and functionality, including water resistance up to 100 meters.
Figure 1: Front view of the SF 77103PP02 watch, showcasing the analog and digital dial.
Figure 2: Side view of the watch, highlighting the control buttons for various functions.
Figure 3: Back view of the watch, showing the stainless steel case back and model number.
Setup
1. Initial Power On
Your watch is powered by a quartz battery. It should be operational upon receipt. If the digital display is blank or the analog hands are not moving, the battery may need to be activated or replaced.
2. Setting Analog Time
- Pull the crown (the small knob on the right side of the watch case) out to the first position.
- Rotate the crown clockwise or counter-clockwise to set the hour and minute hands to the correct time.
- Push the crown back into its normal position to start the analog timekeeping.
3. Setting Digital Time and Date
Refer to the specific button functions for your model. Typically, there are 3-4 buttons around the watch case.
- Press the MODE button (usually bottom left) repeatedly to cycle through time, date, alarm, and stopwatch modes.
- When in time display mode, press the ADJUST button (usually top left) to enter setting mode. The seconds display will flash.
- Use the START/STOP button (usually top right) to increment the flashing value (seconds, hours, minutes, month, day, year).
- Use the RESET button (usually bottom right) to move to the next setting item.
- Once all settings are correct, press the ADJUST button again to exit setting mode.
Operating Instructions
1. Digital Display Modes
Press the MODE button to cycle through the following functions:
- Time Display: Shows hour, minute, second, day of the week, and date.
- Alarm Mode: Set and activate daily alarms.
- Stopwatch Mode: Measure elapsed time.
- Date Mode: Displays month, day, and year.
2. Using the Stopwatch
- Navigate to Stopwatch Mode using the MODE button.
- Press the START/STOP button to begin timing.
- Press START/STOP again to pause the timing.
- Press the RESET button to clear the stopwatch to zero.
3. Activating Backlight
Press the LIGHT button (usually top right or a dedicated button) to illuminate the digital display for a few seconds in low-light conditions.
Maintenance
1. Cleaning Your Watch
Wipe the watch case and strap regularly with a soft, dry cloth. For synthetic straps, a slightly damp cloth can be used, followed by drying. Avoid using chemical cleaners or abrasive materials.
2. Water Resistance
This watch is water resistant up to 100 meters. This means it is suitable for swimming and snorkeling, but not for scuba diving. Do not operate buttons while the watch is submerged in water.
3. Battery Replacement
When the digital display fades or the analog hands stop moving, the battery needs replacement. It is recommended to have the battery replaced by a qualified watch technician to ensure proper sealing and maintain water resistance.
4. Storage
Store your watch in a cool, dry place away from direct sunlight and extreme temperatures when not in use. Avoid exposing the watch to strong magnetic fields.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Analog hands not moving | Dead battery; Crown pulled out. | Push crown in; Replace battery. |
| Digital display blank or dim | Low or dead battery. | Replace battery. |
| Incorrect time/date | Time/date not set correctly. | Refer to "Setting Analog Time" and "Setting Digital Time and Date" sections. |
| Water inside watch | Crown not pushed in; Gasket damage; Buttons operated underwater. | Immediately take to a service center. Avoid further water exposure. |
Specifications
- Model Number: 77103PP02
- Display Type: Analog-Digital
- Movement Type: Quartz
- Case Material: Plastic
- Case Diameter: 54.5 mm
- Case Thickness: 17.1 mm
- Band Material: Synthetic (PU)
- Band Width: 27 mm
- Dial Glass Material: Acrylic
- Water Resistance Depth: 100 meters (330 feet)
- Clasp Type: Buckle
- Item Weight: 120 g
- Manufacturer: Titan Company Ltd
Warranty and Support
For warranty information and customer support, please refer to the warranty card included with your purchase or visit the official SF brand website. Keep your purchase receipt as proof of purchase.
For service inquiries, contact the manufacturer, Titan Company Ltd, or an authorized service center.
Important: Unauthorized repairs or modifications may void your warranty.
