KRAMER VW-4 4 HDMI Output Cascading Video Wall Driver
Periksa apa yang ada di dalam kotak
- VW-4 4 Output Video-Wall Driver
- 1 Adaptor dan kabel daya
- 1 set braket
- 4 Kaki karet
- 1 Panduan memulai cepat
Get to know your VW-4
| # | Fitur | fungsi |
| 1 | DI LED | Menyala hijau saat perangkat dihidupkan. |
| 2 | LED MASUKAN | Lights green when a valid input signal is detected on the input. |
| 3 | OUTPUT LEDs (1 to 4) | Light green when an acceptor is detected on that output. |
| 4 | INPUT HDMI Connector | Hubungkan ke sumber HDMI. |
| 5 | LOOP HDMI Connector | Connect to an additional VW 4 device for configuring a large video wall or to a local monitor. |
| 6 | SERVICE USB Port | Use to perform firmware upgrade. |
| 7 | OUT HDMI Connectors (1 to 4) | Connect to up to 4 HDMI acceptors that make up the video wall configuration. The appropriate segments of the zoomed picture are output on these connectors for connection to the displays in the video-wall.
The output on these connectors is at 1080P resolution. |
| 8 | SETUP 4-arah DIP-sakelar | For fast, basic configuration of the device without needing to be connected to a PC, see Langkah 6: Configure VW-4. |
| 9 | RS-232 3-pin terminal block connector | Use to setup and monitor the VW 4 via the Windows software and to upgrade the firmware. |
| 10 | Konektor ETHERNET RJ-45 | Hubungkan ke PC melalui LAN untuk mengatur dan memantau VW 4 via the configuration app. |
| 11 | Konektor DC 5V | Hubungkan ke adaptor daya yang disediakan. |
Mount VW-4
Install VW-4 using one of the following methods:
- Pasang kaki karet dan letakkan unit di permukaan yang rata.
- Fasten a bracket (included) on each side of the unit and attach it to a flat surface (see www.kramerav.com/downloads/VW-4)..
- Mount the unit in a rack using the recommended rack adapter (see www.kramerav.com/product/VW-4).
BAHAYA
- Pastikan lingkungan (mis., Suhu lingkungan & aliran udara maksimum) kompatibel untuk perangkat.
- Hindari pemuatan mekanis yang tidak rata.
- Pertimbangan yang tepat dari peringkat pelat nama peralatan harus digunakan untuk menghindari beban berlebih pada sirkuit.
- Pembumian yang andal dari peralatan yang dipasang di rak harus dipertahankan.
- Ketinggian pemasangan maksimum untuk perangkat adalah 2 meter.
Hubungkan input dan output
The three devices in this 6×2 diagram are designated 0, 1 and 2. Each output is designated by the device number and its outputs. For example, VW-4 (1) is the second device in this video wall configuration and VW-4 (1-2) is HDMI OUT 2 on that device. 
Hubungkan daya
Connect the power adapter to VW-4 and plug it into the mains electricity. Safety Instructions (See www.kramerav.com for updated safety information) Caution:
- Untuk produk dengan terminal relai dan port GPI\O, silakan merujuk ke peringkat yang diizinkan untuk koneksi eksternal, yang terletak di sebelah terminal atau di Panduan Pengguna.
- Tidak ada suku cadang yang dapat diservis oleh operator di dalam unit.
peringatan
- Gunakan hanya kabel daya yang disertakan dengan unit.
- Putuskan daya dan cabut unit dari dinding sebelum memasang.
Configure VW-4
Configure VW-4 via
- DIP-switch settings – for basic video wall configuration.
- VW-4 app, via the Ethernet or RS-232.
- Dari jarak jauh, dengan perintah serial RS-232 yang dikirimkan oleh sistem layar sentuh, PC, atau pengontrol serial lainnya.
Kontrol / Protokol RS-232 3000 Tingkat Baud: 115,200 Paritas: tak satupun Bit Data: 8 Format Perintah: ASCII Hentikan Bit: 1 Example: (Set Auto-sync Off to Fast): #SCLR-AS 1,2 Parameter Ethernet Default Alamat IP: 192.168.1.39 Pintu gerbang: 192.168.0.1 Subnetmask: 255.255.0.0 Port TCP#: 5000
Video Wall Configuration via DIP-switch Settings
You can use the DIP-switch settings to quickly configure a basic video wall (without bezel correction) of up to 4×4, consisting of 1 or more VW-4 devices.
When the video wall size is configured using the DIP-switches, it is not possible to set it up via the configuration app. (To use the app, make sure that the DIP-switches are all OFF).
| DIP 1 | DIP 2 | DIP 3 | DIP 4 | Columns x Rows Layout | Catatan |
| MATI | MATI | MATI | MATI | Basic setup is not used (default) | |
| MATI | MATI | MATI | ON | Full size picture (“1×1” wall) | Image appears on all displays. |
| MATI | MATI | ON | MATI | N / A | |
| MATI | MATI | ON | ON | N / A | |
| Satu VW 4 alat | |||||
| MATI | ON | MATI | MATI | 2×2 wall (0) | |
| MATI | ON | MATI | ON | 4×1 wall (0) | |
| MATI | ON | ON | MATI | 1×4 wall (0) | |
| MATI | ON | ON | ON | N / A | |
| Tiga VW 4 perangkat | |||||
| ON | MATI | MATI | MATI | 3×3 wall, first unit (0) | |
| ON | MATI | MATI | ON | 3×3 wall, second unit (1) | |
| ON | MATI | ON | MATI | 3×3 wall, third unit (2) | |
| ON | MATI | ON | ON | N / A | |
| Empat VW 4 perangkat | |||||
| ON | ON | MATI | MATI | 4×4 wall, first unit (0) | |
| ON | ON | MATI | ON | 4×4 wall, second unit (1) | |
| ON | ON | ON | MATI | 4×4 wall, third unit (2) | |
| ON | ON | ON | ON | 4×4 wall, fourth unit (3) | |
Video Wall Configuration via the configuration app
Use the VW-4 Windows® Control Software app to configure a video wall of up to 8×8, consisting of 1 or more VW-4 devices (see www.kramerav.com/product/VW-4#Tab_Resources).
To configure the video wall (for example, a 3×2 video wall, using 2 devices)
- 1. Download the latest VW-4 Control Software app from www.kramerav.com/product/VW-4#Tab_Resources.
- Buka aplikasinya.
- Klik Koneksi.
The Connection window opens, showing a list of all the connected VW-4 devices and the available RS-232 ports on your PC. The Connection window opens.
- Select a device under All Units and click . The selected device moves to the Selected Units area.
- Add the other connected devices.
- Klik OK.
- Select the Settings tab and then select the Output tab.
- If you need to change the device ID, enter the new ID under ID-NAME and press Enter on your keyboard.
You can set the ID number individually only when the device is directly connected to your PC. The ID number is set to each device, and according to that number each device is assigned its physical position in the video wall setup. - View the sink status of each device output and:
- Set OSD Info.
- Define Auto-Sync Off status.
- Set the HDCP per output and click Save.
- Pilih tab Tata Letak.
- Set the video wall size by either:
- Selecting Column and Row numbers (for example, 3 x 2). OR
- Clicking Quick Selection for common video wall configurations.
- Select horizontal and vertical bezel corrections (in pixels).
For each connected device, VW-4 App also enables performing factory reset, upgrading the firmware, viewing network settings and copying the EDID to the input from a selected EDID source.
Dokumen / Sumber Daya
 |
KRAMER VW-4 4 HDMI Output Cascading Video Wall Driver [pdf] Panduan Pengguna VW-4, 4 HDMI Output Cascading Video Wall Driver, VW-4 4 HDMI Output Cascading Video Wall Driver, Video Wall Driver, Wall Driver, Driver |
