Saooer BLUE 20A
Saooer 20A Solar Charge Controller User Manual
Model: BLUE 20A
Perkenalan
This manual provides essential information for the safe and efficient operation of your Saooer 20A Solar Charge Controller. This intelligent regulator is designed to manage the working of solar panels and batteries in a solar system, featuring dual USB ports for mobile device charging. It is compatible with 12V and 24V systems and includes multiple protection functions to ensure system efficiency and prolong battery lifespan.
Gambar 1: Depan view of the Saooer 20A Solar Charge Controller.
Petunjuk Keselamatan
- Ensure all connections are correct before powering on the controller. Incorrect wiring can damage the device or connected components.
- The controller is designed for indoor use or in a protected environment. Avoid exposure to direct sunlight, high temperatures, or moisture.
- Jangan mencoba membongkar atau memperbaiki pengontrol sendiri. Serahkan perbaikan kepada personel yang berkualifikasi.
- Jauhkan dari jangkauan anak-anak.
- This controller is only suitable for lead-acid batteries: OPEN, AGM, GEL. Do not use with other battery types like Lithium-ion or LiFePO4, as this may cause damage or safety hazards.
- Always connect the battery first, then the solar panel, and finally the load. When disconnecting, reverse the order: disconnect the load, then the solar panel, and finally the battery.
Fitur Produk
- Sistem Otomatis Voltage Identifikasi: Automatically detects 12V/24V system voltage.
- PWM Charging: Efficient Pulse Width Modulation charging mode.
- Port USB Ganda: Provides 5V/2A output for charging mobile devices.
- Layar LCD: Clear display of status and data, allowing for convenient mode switching and parameter configuration.
- Fungsi Perlindungan Ganda: Includes short-circuit protection, open-circuit protection, reverse protection, and over-load protection.
- Parameter yang Dapat Disesuaikan: User-adjustable charge and discharge parameters.
- Kompensasi Suhu: Automatic temperature compensation for optimal charging.
Pengaturan dan Instalasi
Follow these steps carefully to install your solar charge controller. Incorrect installation can lead to damage or malfunction.
- Persiapan Pengkabelan: Ensure all wires are properly stripped and have appropriate connectors if necessary. Use wires of sufficient gauge for your system's current.
- Hubungkan Baterai: Connect the battery to the charge regulator first. Observe correct polarity (+ to + and - to -). The controller will automatically recognize the battery voltage (12V atau 24V).
Gambar 2: Sisi view showing the connection terminals for battery, solar panel, and load.
- Hubungkan Panel Surya: Connect the solar panel to the solar charge controller. Ensure correct polarity.
- Hubungkan Beban: Connect the consumer or load to the charge controller regulator. Ensure correct polarity.
Catatan Penting: Always connect the battery first, then the solar panel, and finally the load. When disconnecting the controller, please remove the solar panel, then the load, and finally the battery. This sequence helps the controller recognize the battery voltage correctly and prevents damage.
Petunjuk Pengoperasian
Layar LCD dan Tombol
Gambar 3: Sudut view showing the LCD display and control buttons.
The controller features an LCD display and three buttons for operation:
- Tombol Menu: Used to cycle through display modes and enter parameter setting mode.
- Tombol Atas: Used to increase values or navigate upwards in menus.
- Tombol Bawah: Used to decrease values or navigate downwards in menus.
Mode Tampilan
Press the Menu button to cycle through the following display modes:
- Vol bateraitage (V)
- Panel Surya Voltage (V)
- Arus Beban (A)
- Battery Temperature (°C)
- Arus Pengisian (A)
- Arus Pelepasan (A)
- Load Working Mode (24H, 0-23H, 0H)
Pengaturan Parameter
To enter parameter setting mode, press and hold the Menu button for 5 seconds. Use the Up and Down buttons to adjust values, and the Menu button to confirm and move to the next parameter. Press and hold Menu again to exit setting mode.
| Parameter | Keterangan | Default (12V) | Range (12V) |
|---|---|---|---|
| Bahasa Indonesia: B01/B02/B03 | Battery Type Selection (B01=Lead-acid, B02=Lithium Ion, B03=LiFePO4) | B01 | Tidak tersedia |
| Charge Off Voltage | Jil.tage at which charging stops | 14.4V | Tegangan 13.0V - 15.0V |
| Discharge Reconnect Voltage | Jil.tage at which load reconnects after low voltage putuskan | 12.6V | Tegangan 11.0V - 13.5V |
| Discharge Stop Voltage | Jil.tage at which load disconnects to protect battery | 10.7V | Tegangan 9.0V - 11.5V |
| Load Working Time | Timer for load output (24H, 0-23H, 0H) | 24 jam | Tidak tersedia |
Note: For 24V systems, multiply the 12V values by two.
Pemeliharaan
- Pemeriksaan Rutin: Periksa secara berkala semua sambungan kabel untuk kekencangan dan korosi.
- Kebersihan: Keep the controller clean and free from dust. Use a dry cloth for cleaning.
- Ventilasi: Ensure adequate ventilation around the controller to prevent overheating.
- Kesehatan Baterai: Memantau volume bateraitage and health regularly. Replace batteries as needed.
Penyelesaian Masalah
| Masalah | Kemungkinan Penyebab | Larutan |
|---|---|---|
| Pengontrol tidak menyala / LCD kosong | Baterai tidak terhubung atau polaritas terbalik; Tegangan bateraitage terlalu rendah. | Check battery connections and polarity. Ensure battery has sufficient charge. |
| Panel surya tidak mengisi daya baterai. | Solar panel not connected or reverse polarity; Insufficient sunlight; Damaged solar panel. | Check solar panel connections and polarity. Ensure panel is in direct sunlight. Test solar panel output. |
| Pemuatan tidak berfungsi | Load not connected or reverse polarity; Battery voltage too low (low voltage disconnect); Overload protection activated. | Check load connections and polarity. Charge battery. Reduce load or check for short circuit. |
| Port USB tidak mengisi daya | Volume bateraitage too low; Device not compatible; Faulty USB cable. | Ensure battery is charged. Try a different device or cable. |
| Controller gets hot | Overload; Poor ventilation. | Reduce load. Ensure controller has adequate airflow and is not in an enclosed space. |
Spesifikasi
| Fitur | Detil |
|---|---|
| Model | BIRU 20A |
| Volume Sistemtage | 12V / 24V Otomatis |
| Arus Pengisian/Pengosongan Maks | 20A |
| Keluaran USB | Dual USB, 5V/2A (Max) |
| Kompatibilitas Jenis Baterai | Lead-acid (OPEN, AGM, GEL) |
| Dimensi Produk | 5.12 x 2.76 x 1.5 inci (sekitar 133 mm x 70 mm x 38 mm) |
| Berat Barang | 5 ons |
| Menampilkan | Layar LCD |
| Suhu Operasional | -35°C hingga +60°C |
Figure 4: Product dimensions of the solar charge controller.
Garansi dan Dukungan
For warranty information or technical support, please contact the manufacturer, Saooer, through their official channels. Refer to your purchase documentation for specific warranty terms and contact details.
Pabrikan: Saooer
ASIN: B095764VB7
UPC-nya: 605832982977
Anda dapat mengunjungi Saooer Store on Amazon untuk informasi lebih lanjut atau menghubungi dukungan.