HYPERX Cloud Stinger Core Wireless Gaming Headset User Guide
Overview
- A. Swivel to mute microphone
- B. Status LED
- C. Power button
- D. Volume wheel
- E. USB charge port
- F. USB adapter
- G. Wireless pairing pin hole
- H. Wireless status LED
- I. USB charge cable
Using the Headset
- Connect the wireless USB adapter to your device.
- Power on the headset.
Status LED
| HEADSET STATUS | LED |
| Pairing | Flashing green and red every 0.2s |
| Searching | Slow breathing green |
| Connected | 90% — 100% battery: Solid green |
| 15% — 90% battery: Blinking green | |
| < 15% battery: Blinking red |
Power Button
Power on/off – Hold power button for 3 seconds
Volume Wheel
Scroll up or down to adjust volume level.
WARNING: Permanent hearing damage can occur if a headset is used at high volumes for extended periods of time.
Swivel to Mute Microphone
Charging
| CHARGE STATUS | LED |
| Fully charged | Solid green |
| 15% — 99% battery | Breathing green |
| < 15% battery | Breathing red |
Overview
- A – Swivel to mute microphone
- B – Status LED
- C – Power button
- D – Volume wheel
- E – USB charge port
- F – USB adapter
- G – Wireless pairing pin hole
- H – Wireless status LED
- I – USB charge cable
Using the Headset
- Connect the wireless USB adapter to your device.
- Power on the headset.
HyperX NGENUITY Software
Download software and latest Firmware updates at:
hyperxgaming.com/ngenuity
Status LED
| HEADSET STATUS | LED |
| Pairing | Flashing green and red every 0.2s |
| Searching | Slow breathing green |
| Connected | 90% – 100% battery: Solid green |
| 15% – 90% battery: Blinking green | |
| < 15% battery: Blinking red |
Power Button
Power on/off – Hold power button for 3 seconds
Volume Wheel
Scroll up or down to adjust volume level.
WARNING: Permanent hearing damage can occur if a headset is used at high volumes for extended periods of time.
Swivel to Mute Microphone
Charging
It is recommended to fully charge your headset before first use.
| CHARGE STATUS | LED |
| Fully charged | Solid green |
| 15% – 99% battery | Breathing green |
| < 15% battery | Breathing red |
Questions or Setup Issues?
Contact the HyperX support team at:
hyperxgaming.com/support/headsets
Battery/TX Power Info
| Battery Information |
| Contains 3.7V, 1000mAh Li-ion Battery, 3.7Wh Cannot be replaced by user |
| Frequency & TX Power Information |
| Frequency Bands: 2.4GHz (TX Power: <2dBm) |
FCC Compliance and Advisory Statement
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures:
- Reorient the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any special accessories needed for compliance must be specified in the instruction manual.
Warning: A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception.
It is essential that only the supplied power cord be used.
Use only shielded cables to connect I/O devices to this equipment.
CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Canada statement
Canada Notices
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
NTC
Type Accepted
No. ESD-2021447C
| TRA REGISTERED No: ER77286/19 |
| DEALER No: DA81684/19 |
| 66396/SDPPI/2020 9100 |
NTC
Type Accepted
No. ESD-2021474C
| TRA REGISTERED No: ER77285/19 |
| DEALER No: DA81684/19 |
| 66397/SDPPI/2020 9100 |
Questions or Setup Issues?
Contact the HyperX support team at: hyperxgaming.com/support/headsets
Documents / Resources
 | HYPERX Cloud Stinger Core Wireless Gaming Headset [pdf] User Guide Cloud Stinger Core Wireless Gaming Headset, Cloud Stinger Core, Wireless Gaming Headset, Gaming Headset, Headset |
