Owner's Manual for OSD NERO models including: Stream ARC BT Amplifier, ARC BT Amplifier, BT Amplifier, Amplifier
Santos Electronics NEROSTREAMARC BT Amplifier 2A4UHNEROSTREAMARC 2A4UHNEROSTREAMARC nerostreamarc
Stream ARC /BT Amplifier Owner's Manual Important Safety Precautions NERO ARC Integrated AMP/PREAMP Owner's Manual NERO ARC Introduction Integrated Amp/Preamp, 100-watt per channel RMS Class D Stereo Amplifier with ARC, Wireless, USB plus 3 other inputs, subwoofer output, and remote control. The OSD Nero ARC amplifier makes a great choice for improving the sound from your TV or computer speakers. This versatile amp's ARC, 24/192 USB Audio, BT Wireless, digital, and linelevel Inputs ensure connectivity with your existing equipment. With Its range of 6 different inputs, it also makes a great stand-alone Integrated amp. Small enough to be mounted behind your TV. Add A bookshelf, floor-standing speakers, and a subwoofer to get Theater-quality sound. Alternatively, use in-wall speakers for an aesthetically pleasing solution. Improves your laptop or computer sound; connect using ARC, USB, or headphone outputs, add desktop speakers, and transform your home office audio experience. The front-mounted volume control makes it quick and easy to adjust the sound level. Features 2 x 100 Watts RMS 4 Ohms, for high power sound 1 x 200 Watts peak power for maximum dynamics Class D design for maximum efficiency and low-cost running Greater than 95 dB SNR for low noise and clear sound Six separate inputs, including ARC for TV and computer connection Volume, Bass, and Treble controls allow you to `dial in' exactly the sound you want Auto stand-by turns the amp off when not being used. ARC Connection Connect the ARC-approved HDMI cable to the Input Port labeled ARC or eARC. The other end connects the ARC input on the back panel of the NERO ARC Integrated AMP/PREAMP. This will only work if both connections are ARC-ready. This allows the TV's audio output through the ARC connection and enables the CEC control between the TV and the NERO ARC device so that the TV remote control can control the NERO ARC without the need for Programming. Note: You will most likely have to change the TV settings, disabling their internal speakers while enabling the audio output through the ARC port of the television. Some TVs may require adjustments for the ARC port to enable the CEC operation. Connection Via Wireless BT Receiver Mode The NERO ARC features Wireless BT Connect as an option. You can access the Wireless BT 5.3 manually using the front panel Volume/Source Select Knob or by using the IR Remote that is included with the NERO ARC. When in receiver mode, the Wireless BT LED will flash, which indicates it is waiting for a connection in your BT Transmitter device (cell phone, pad, TV). You can search for the device name "OSD Player." Once connected, the BT LED will stay on, which indicates the connection is successful. You can start playing music from the connected device and hear the sound coming out of the connected passive speakers. NERO ARC Integrated AMP/PREAMP Connections Analog Line-In/Sub Output Connect any Playback device with Audio out/Line out/Aux out to Line in using an RCA cable. For example, a CD/DVD Player or Headphone connection from your Smartphone. Analog Device Audio Out RL Powered Sub Audio Inputs R LFE L Connect the output of the NERO ARC to a Powered Subwoofer Input or Subwoofer Amp input using an RCA Sub Cable, single or single to dual RCA Sub cable Digital Optical/Coaxial Inputs Connect any playback device with Digital Fiber output to Optical input using Optical Cable (TV, AVR) Digital Device Fiber Optic Output Digital Device Digital Coax Output For the other Digital connection, this makes sure you are covered for both Fiber and Coax applications DAC USB Type C Input From USB Type A Output Transfer Native Digital signal from your Desktop or Laptop Computer to the DAC Type C Input on the NERO ARC utilizing the Audiophile DAC (Digital to Analog Convertor) featured in the NERO ARC Laptop Computer USB-A Output NERO ARC Callouts, Front Panel Front Panel Controls 1. POWER/STATUS INDICATING LIGHT The Green light indicates regular operation, the red light indicates FAULT, and the orange light indicates waveform trim 2. POWER SWITCH Used to turn on or off the power of the internal amplifier 3. VOLUME/SOURCE SELECTION CONTROL KNOB The Volume/Select Knob is rotated to the left (counterclockwise) to turn the volume down and turn to the right (clockwise) to increase the volume. Press the Volume/Select Knob to Cycle through the sources one at a time: Wireless BT, Digital Optical, DAC, ARC, Digital Coax, and Line in. Hold the Volume/Source knob down to restore factory settings. In the standby state, press the Knob to wake up the power amplifier 4. IR WINDOW Used to receive the infrared signal of the remote control Amplifier Standby The power amplifier has an automatic shutdown function; in the absence of any audio input, it will enter the automatic standby state within 10 minutes; Standby power consumption 0.5W; you can use the standby button of the remote control or touch the switch through the encoder on the panel to wake up the power amplifier. The power amplifier has a power-off memory function. When powered off and then powered on again, it will return to the parameters before the shutdown, such as EQ, sound source, etc. What's in the Box IR Remote Wall Mount Brackets Power Cord 2 AAA Batteries Wireless BT Antenna QR Code Warranty Card NERO ARC Callouts, Rear Panel Controls REAR PANEL CONTROLS 5. Wireless BT external antenna To maintain the stability of Wireless BT communication, it is necessary to rely on the assistance of external antennas, which will greatly improve the distance and stability. 6. Digital DAC input Used to play USB C disk music and connect computer playback. 7. Analog AUX input It can play music by connecting to CDs, DVDs, set-top boxes, and other audio sources with analog audio output devices. 8. Speaker output Terminals Five-way Binding posts can connect a pair of 4-ohm, 8-ohm, or two pairs of 8-ohm speakers (with a 4-ohm load). 9. AC outlet It supports AC 100 - 120V/220 - 240V voltage input and can adapt to the power supply voltage of different countries worldwide. 10.Digital OPTICAL input To achieve sound source playback, you can connect some devices with OPITC output, such as TVs and karaoke machines. 11.Digital ARC input Some devices with ARC, such as TVs and karaoke machines, can be connected to achieve music playback. 12.Digital COAX input Some devices with COAX output, such as TVs and karaoke machines, can be connected to achieve music playback. 13.Analog SUB output It connects to an active subwoofer for a stronger bass effect. NERO ARC IR Remote Control IR Remote 1. Power LED Flashing indicator 2. Power Button 3. Volume Mute Button 4. Vol+/Volume5. Forward/Rewind 6. Pause/Play Button 7. Bass +/8. Treble +/9. Source Select Button 1. Wireless BT 2. Optical 3. DAC USB-C 4. ARC 5. Digital Coax 6. Line -In Dimensions and Specifications NERO ARC Categories Amplifier type Design type Channels Wireless BT version Peak power output 8-ohm Power Rating 4-ohm Power Rating Frequency Response Impedance Signal to Noise Ratio ARC Specifications ARC Specs Two Channel L&R Stereo Digital Class D 2 Wireless BT 5.3 (chip:BT8961) 200W 50W x 2 RMS, 2 x 100W Peak Power 100W x 2 RMS, 2 x 200W Peak Power 20Hz-20kHz 8 Ohm to 4 Ohm Stable >95dB A-weighted Categories ARC Specs Sources/ Inputs Wireless BT / Optical / DAC / ARC / Coax / LINE IN Output Maximum Sample Rate Bit Resolution Supports 24Bit/192kHz Wall Mountable Remote Control Dimensions (L x H x D) Weight L/R speaker out (mono) / SUB Out 44.1kHz, 48kHz, 96kHz, 192kHz 16-24 bits Yes Yes Yes 7.48" x 1.97" x 5.5" ( 190*50*140 mm) about 1.13 KG NERO Electronics Warranty FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help important announcement Note: Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Adobe PDF Library 24.2.159