Document

HUNTER-LOGO

Hunter KE19101L24 5 Light Chandelier

Hunter-KE19101L24-5-Light-Chandelier-PRODUCT-IMAGE

Hunter-KE19101L24-5-Light-Chandelier-01Hunter-KE19101L24-5-Light-Chandelier-02

5 Light Chandelier
Fixture weight ±2 lbs: 7 lbs (3.2 kg)

Hardware Service Kit
Part  Model  Finish

KE19101L24  19741 Palm Gold
KE19101214 19742 Brushed Nickel

Here are the tools you’ll need to complete your installation:

Ladder
Hunter-KE19101L24-5-Light-Chandelier-03

Screwdriver

Hunter-KE19101L24-5-Light-Chandelier-04

Pliers

Hunter-KE19101L24-5-Light-Chandelier-05

Wire Strippers

Hunter-KE19101L24-5-Light-Chandelier-06

PREPARING FOR INSTALLATION

Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. Remove cap nuts (H) from mounting screws (B). Place the mounting plate (A) over the junction box so that mounting screws (B) and nuts (C) extend out away from the ceiling. Adjust the position of mounting screws (B) so that mounting screws (B) can be exposed 5-6 mm after passing through the canopy (F) to properly fit the cap nuts. Depending on the placement of your junction box the position of mounting screws (A) may need to be adjusted to allow the canopy to be flush with the ceiling. Mounting screws (B) can be adjusted by loosening nuts (C) and loosening or tightening mounting screws (B). Once the ideal position of mounting screws (B) has been confirmed, tighten nuts (C) on mounting screws (B) on the front of the mounting plate to ensure that mounting screws (B) are secure. Pull the house wires through the center of mounting plate (A). Secure mounting plate (A) to the junction box by tightening the screws (D).

ASSEMBLING THE FIXTURE

There are 4 12-inch rods (K), and 1 6-inch rod (I) included for each fixture. Determine the correct number of rods needed for proper hanging height. To lengthen the fixture, add additional rods. To shorten the fixture, trim the wires to desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the fixture’s wiring to discard. Keep in mind that you must use at least one rod to hang the fixture. Thread the wires through the center rod (L) and attach to the threaded post (Q) on the fixture (M). Thread the wires through the rods and pull the wires until taut before connecting the rods together. All threads should be engaged but do not overtighten (some manual straightening of the downfolds may be required). Screw the rod (K or I) on the threaded post of center rod (L). Pull the fixture wires through the top of the canopy (F). Screw the top rod to hang straight (G) of canopy (F). Then use the socket ring (O) to secure the glass shade (N) to each socket. Screw the finial (P) on the fixture (M) beneath each socket.

CONNECTING THE WIRES

Hunter-KE19101L24-5-Light-Chandelier-07

Have a helper support the fixture’s weight while completing the wiring. Attach the fixture’s wires to the power supply wires from the junction box. Connect black to black (Live); white to white (grounded); grounding to grounding (green or copper). Twist the ends of the wire pairs together. Then, twist on a wire connector. Make sure all twists are in the same direction. Loop fixture’s ground wire around grounding screw (E) and tighten. If there is no ground wire (green or copper) from the junction box, contact a qualified electrician.

FINISHING THE INSTALLATION

Raise canopy (F) to mounting plate (A) and position mounting screws (B) so that they protrude through the openings of canopy (F). Secure canopy (F) in place with cap nuts (H). Install light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Your installation is now complete. Turn on the power and test the fixture.

CLEANING TIPS

Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.

NOTICE
In order to use a 12in rod by itself you must first remove the post from the 6in rod and install it on one of the ends of the 12in rod.

Hunter Pro Tip:
Twist or tape wire ends together to make it easier to pass them through the downfolds. Threaded post may also be removed for easier wire access.

Documents / Resources

Hunter KE19101L24 5 Light Chandelier [pdf] Instruction Manual
KE19101L24, 5 Light Chandelier, Light Chandelier, KE19101L24, Chandelier

Leave a comment

Your email address will not be published. Required fields are marked *