SloanLED 100L1 24 VDC Power Supply - logo100L1 24 VDC Power Supply
Installation Guide

SloanLED 100L1 24 VDC Power Supply - figure 1 SloanLED 100L1 24 VDC Power Supply - figure 2
1. Tools required: Wire strippers, drill, and screwdriver. 2. Supplies required: Conduit and electrical enclosure for power supply (if not placed in a sign made from enclosure rated material), #8 pan head screws, UL Listed PLTC cable, UL Listed electrical wire connectors (e.g., wire nuts), silicone. Europe: Electrical enclosure for power supply, M4 pan head screws, PLTC cable, silicone, 3M™  Scotchlok™ connectors.
SloanLED 100L1 24 VDC Power Supply - figure 3 SloanLED 100L1 24 VDC Power Supply - figure 4
3. Power Supply: Identify primary wires, secondary wires, and the location of mounting tabs. 4. Mount Power Supplies: Use mounting tab in the corner to secure power supply.
SloanLED 100L1 24 VDC Power Supply - figure 5
5. Connect Primary: CAUTION: Have a licensed electrician connect to the primary.

JEGYZET: Ensure adequate ventilation. Power supply operating ambient temperature is -40º to 55º C. Power supply must be mounted in an enclosure (i.e., the transformer can/raceway). Power supply spacing to thermoplastic, wood, fiber, or other combustible type enclosure materials shall be 1″ (25 mm). Two or more adjacent power supplies shall not be mounted closer than 1″ (25 mm) end to end or 4″ (102 mm) side to side.
If mounted inside a sign cabinet, UL requires that the cabinet is made from an enclosure-rated material. Ensure power supplies are not overloaded by verifying output current is less than 4.15 DC Amps. It is recommended to use photocells or light sensors to prolong the life of the power supply and to keep unit at maximum operating efficiency.

HIBAELHÁRÍTÁS

If the sign is not functioning properly, check the following:

  • Elsődleges kötettage is between 120-277 VAC
  • Secondary voltage is 24 VDC
  • Output current is 4.15 Amps or less
  • The power supply is not overloaded (see power supply capacity chart in product installation guide or SloanLED.com)
  • There are no shorts in the secondary wiring
  • All secondary connections are RED-TO-RED and BLACK-TO-BLACK

SloanLED products carry a limited warranty.
For complete details refer to the warranty policy found at SloanLED.comSloanLED 100L1 24 VDC Power Supply - iconSome or all of the products shown are covered by U.S. and foreign patents pending and covered by one of more of the following U.S. patents issued:
6776504, 6969179, 7192157, 6932495, 7241031

SloanLED 100L1 24 VDC Power Supply - logoÜgyfélszolgálat és műszaki támogatás
SloanLED főhadiszállás
5725 Olivas Park Drive, Ventura, CA, USA
888.747.4LED (888.747.4533) • [e-mail védett]
SloanLED.com
P/N 402794 Rev A 2021-03-24
SloanLED Europe bv
Argonstraat 110, 2718 SN Zoetermeer, NL
+31 88 12 44 900 • [e-mail védett]

Dokumentumok / Források

SloanLED 100L1 24 VDC Power Supply [pdf] Telepítési útmutató
701895-100L1, 100L1 24 VDC Power Supply, 100L1, 24 VDC Power Supply

Véleménye fontos számunkra!

E-mail címed nem kerül nyilvánosságra.