User Manual for LOWES models including: 30036 Ceiling Fan with Light, 30036, Ceiling Fan with Light, Fan with Light, Light, Fan
10 ore fa — Place the downrod inside the canopy, canopy cover, and yoke cover. - Route wires exiting motor through yoke cover, canopy and downrod.
5 days ago —
1 giorno fa — Place the downrod inside the canopy, canopy cover, and yoke cover. - Route wires exiting motor through yoke cover, canopy and downrod.
CEILING FAN WITH LIGHT ITEM #30036 support@ceilingfanhelp.com Installation Instructions Troubleshooting Guide Balancing Kit 5-10 11 12 To reduce the risk of fire or injury do not use this product in conjunction with any variable (rheostat) wall control. objects. 5. To clean the fixture ,turn off the power, wait for it to cool, and wipe the fixture with a clean dry, soft cloth. 7. All screws must be checked and retightened where necessary before installation. 2 5.9 in 2.2 in 12.8 in 15.4in S1 S2 S3 S4 OFF ON/ OFF F R 3 2 4 SET 1 USPTO P 5 6 1H 4H 8H 2 3 4 5 6 56 in S5 Hardware Package S1.Machine Screw S6 S2.Washer S3.Wood Screw S7 S4.Wire Nut S5.Blade Screw S6.Blade Washer(Red) S7.Balance Kit Item name 7 1.Remote Control 2.Mounting Bracket 3.Canopy 8 4.Canopy Cover 5.Yoke Cover 6.Downrod 7.Long Downrod 9 8.Motor Housing 9.Lamp Housing 10.Lamp Shade 11.Blade 10 11 3 Quantity 2 4 4 3 17 17 1 1 1 1 1 1 1 1 1 1 1 5 Receiver Bolt jam Screws Motor Housing Lamp Housing Lamp housing screw Lamp shade Hanger Canopy screw Mounting Bracket Canopy Canopy Cover Yoke Cover Cotter Pin Blade Blade Washer(Red Blade Screw 4 Mounting - Take out fan downrod. - Remove cotter pin and bolt from downrod. - Take out fan motor housng. - Loosen jam screw in yoke until it is flush with the inside surface. - Place the downrod inside the canopy, canopy cover, and yoke cover. - Route wires exiting motor through yoke cover, canopy and downrod. - Insert bolt through hole in and downrod. Be careful not to damage or cut the fan wires. - Tighten bolt. Secure with cotter pin through hole in the end of the bolt. - Secure downrod in position by tightening jam screws. - Slide yoke cover down and it will flush with the motor housing. Fig.1a Cotter Pin Fig.1b Downrod Jam Screw Bolt Yoke Fig.1c Fig.1d Yoke Cover Bolt Downrod Canopy Canopy Cover Cotter Pin Yoke Fig.1e Jam Screw Jam Screw Downrod Canopy Canopy Cover Yoke Cover Motor 5 Step2 Install Mounting Bracket - Secure hanger to metal outlet box. - The ceiling fan is hung on the hanger, with the hanger ball groove aligned with the hanger boss. Fig.2a Fig.2b Fig.2c Outlet Box washer Hanger Outlet Box Screw not provided hanger boss hanger ball groove Step3 Attaching the Fan Blades. - Attach the blade to the motor with blade screws. - Repeat this step for each blade assembly. Outlet Box Canopy Canopy cover Yoke cover Motor housing 1 Blade Washer(Red) 2 Blade Screw Fig.3 6 Step4 Assembling the lamp housing - Feed the wire through the center hole of the lamp housing. - Fix the lamp housing with screws. - Connect the motor end plug to the light source end socket. Fig.4 Step5 The lampshade installation - Install the lampshade to the lamp housing by turning clockwise to lock it into place. Fig.5 1 2 7 Step6 The receiver installation - Put the receiver in the hanger. Fig.6a Fig.6b Step7 Wiring the Fan - Wiring according to the wiring diagram. Fig.7a From ceiling white black white black white blue white blue From fan earth wires (From ceiling) earth wires (From fan) NOTE: Once earth wires are connected, carefully tuck all wires and marrettes into the metal box making sure that the wires are clear of the hemisphere and downrod when positioned in hemisphere and downrod when positioned in mounting bracket. 8 Step8 Attaching the Canopy and Canopy cover - Slide the canopy up to the ceiling and attach it to the hanger with the screws provided. Tighten all screws securely. - Move the Canopy cover onto the canopy. (the decorative cover comes with magnetism) Fig.8a Fig.8b Fig.8c Canopy hanger screw 2 Canopy cover 1 CONGRATULATIONS! YOU HAVE COMPLETED THE INSTALLATION 9 FUNCTION INSTRUCTION OF EMITTER - Open battery cover on the hand-held remote and install battery, pair of AAA of emitter(1.5V) that are not included. - Please pair the remote before using: Turn on the power switch, press the" 2 + " within 3 seconds, the receiver issued a"tick"two sounds, the pair code is successful. If not successful, turn off the power for a minute an repeat the above. -When the emitter cannot control the receiver,please check the battery switch touching normally or not, correction of the positive and negative, full or empty of the power. -When the emitter cannot control the receiver, please check is there any existence of similar remote controlled products nearby, then check whether they works, because remote controlled product with the same frequency will disturb each other. -Please take out the battery from the emitter when leaving unused for long time. - When installing the fan, the fan ceiling cover don't press the antenna(or other wire), it is easy to breakdown the wire and short-circuited. 1 All off 2 Fan forward rotating 3 Natural wind 4 Speed control 1 5 Fan off 2 6 Timer 7 Light switch on/off (Color temperature can be selected) 3 8 Fan reversal rotating 4 9 Trun OFF the beeping 5 After powering on, press and hold " " on the handle immediately. After hearing the beep, release the " " 6 button to turn off the beeping. (If you need to turn the prompt sound back on, turn off the power first, then turn it on again, and repeat the above actions) OFF ON/OFF 7 F R 8 3 2 4 1 5 STOP 6 1H 4H 6 9 Light Memory Function: 1. The default light color when the ceiling fan is turned on. 2. The light will lock in a specific color temperature after turning on the light for 10 seconds. 3. The color temperature will be the same as the last time when turning on the light next time. 10 11 BALANCING WEIGHT PLASTIC CLIP 12Corel PDF Engine Version 21.2.0.706 CorelDRAW 2019